Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

my lawn mower died, but this is not OT,

Posts

my lawn mower died, but this is not OT,

#1

my lawn mower died, but this is not OT,

Mark in B'ham, AL

>I took it apart, cleaned it and put it back together, so now it's clean and dead and possibly jumbled up. Anyway, I got a new one on sale at the BORG. Which leaves me with an old mower, so I got to thinking that maybe I could use the old blade to make tools.

Now, I have no metal working experience, but what I was thinking was to try making a scraper. Do you all think that the metal in the blade will be good for this purpose?

Thanks, Mark

Re: my lawn mower died, but this is not OT,

#2

Steven Antonucci

I dunno...

steve antonucci

>I can tell you that I just changed the blade in my mower after hitting rock in tall grass. Mother of all catches- blew the air filter off the carb... but I digress.

I tried to bend it back into shape and it's certainly tough steel, but it seems kind of soft. I used to sharpen it with a file. Doubt you'd get a refined edge, and I don't know if it would last very long.

Steve

Re: my lawn mower died, but this is not OT,

#3

Good point.

Mark in B'ham, AL

>It may require some heat treating. I wonder if what kind of steel it might be. I tried to bend one back into shape once too and it seemed pretty springy. That might be a bad thing during a catch on the lathe.

Re: my lawn mower died, but this is not OT,

#4

Re: my lawn mower died, but this is not OT,

john lucas

>Lawn mower blades are good steel. Several of the students at the Craft Center have made knives from them. I cut a chunk off of one to use for a scraper cutter and it works well. I don't have any idea what kind of steel it really is but it takes heat treating well.

Re: my lawn mower died, but this is not OT,

#5

Thanks for the info, John

Mark in B'ham, AL

>

Re: my lawn mower died, but this is not OT,

#6

Re: my lawn mower died, but this is not OT,

Texian

>John, Used to be something like ordinary 1070 steel, but that was decades ago. What (details) sort of heat treat procedure was used?

Re: my lawn mower died, but this is not OT,

#7

Re: my lawn mower died, but this is not OT,

john lucas

>I just used basic blacksmithing heat treating, heat to cherry red, quench in oil, temper by putting it in the oven at 425 degrees, the let it cool. Very unscientific and I can't really tell you if it's any better or worse than using good steel. It works for what I needed it to do at the time.

Re: my lawn mower died, but this is not OT,

#8

Steven Antonucci

Are you only treating the cutting edge?

steve antonucci

>I use a MAPP torch and I've had difficulty in heat treating "big" pieces of steel because I can't get a uniform temperature or enough heat to bring that much steel up to temperature. Tried a coal fire, but nowhere near the temperature I need.

I need a small woodburning firepit. (used the household fireplace once- but glowing metal inside the house is a BAD idea!)

I've had luck up to about 5/16" thick O1, but results fall off after that...

Steve

Re: my lawn mower died, but this is not OT,

#9

Re: Are you only treating the cutting edge?

Jerry McCaffrey

>Steve

You're welcome to stop down and use my coal fired forge. A little smith coal and some air blown in and you get nice even heat.

Jerry

Re: my lawn mower died, but this is not OT,

#10

Re: Are you only treating the cutting edge?

john lucas

>Steve Take a hair dryer to your coal fire. You can get it hot enough that way. You can anneal them quite easily by just setting them in the coal fire and letting the coal burn out. It stays red hot long enough to soften the steel. Then when heat treating it I have used a charcoal bricket fire with a hair drying blowing into it. Granted this isn't anywhere near as good as a real coke fired forge but it did work.