Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

System 3 Epoxy

Posts

System 3 Epoxy

#1

System 3 Epoxy

Tommy Holmes

>I am planning on buying System 3 epoxy for glue and filling cracks and voids in turnings. I am not sure which additive to get to increase the viscosity. Woodcraft has wood flour, silica thickener and phenolic microballoons, if i need one at all. With the low viscosity of epoxy I assume I do though. Any suggestions on if or which one to buy are appreciated.

Re: System 3 Epoxy

#2

Re: System 3 Epoxy

Chuck Engstrom

>Hi Tommy -- Your choice of thickener depends on what you want the epoxy/thickener combination to do. My general practices go like this:

silica thickener: use when you want to thicken the epoxy so that it doesn't run. Most epoxy "glues" probably use this (also called Cabosil) as an additive to make somewhat liquid epoxy become a thixotropic paste.

micro balloons: use these light-weight tiny tiny plastic bubbles to create a putty for filling cracks, dings, etc to fair up a surface. They do not provide much strength at all and should be avoided when strength is an important issue. Sands easily, usually the main reason to use it.

wood flour: can be used to give some color to your mix. I've saved little jars of several wood sanding dust to use this way -- cherry, walnut, teak, etc. Coffee grounds will give you a pretty good imitation of most dark-colored tree barks. Not terribly strong.

West System, another supplier of many epoxy products, has a chart for selecting fillers at http://westsystem.com/webpages/productinfo/guide/index.htm#fillers. Their stuff is compatible with System Three epoxies.

I have used System Three for many years and measure it out with an old pair of large-sized hypodermics, one 60cc the other 30cc. This method allows you to mix only as much as you need -- I can mix up as little as 2cc resin and 1cc hardener with reliable success. Epoxy has never been cheap, and with oil now over $140, I hate to think of wasting any. Shelf life, by the way, is virtually unlimited: the S3 stuff I am using these days was given to me about twenty years ago and still works fine.

Re: System 3 Epoxy

#3

Re: System 3 Epoxy

Gil Jones

>I use West System epoxy, and like it just fine (and System 3 is probably as good). The West System "404 High-Density Adhesive Filler" seems to do a good job for me (when I need a filler).

FYI !!!! If you use any of the fillers, DO NOT BREATHE them. Most fillers are light enough to become airborne during the adding and mixing, and they are very damaging to your lungs.

Gil

Re: System 3 Epoxy

#4

Re: System 3 Epoxy *LINK*

Mike Cunningham

>Tommy,

I agree with Chuck and Gil. I would however suggest you check out Raka products which I've been using for about 7 years restoring boats. Same quality as the other products but cheaper, at least the last time I purchased it(long shelf life).


Raka

Re: System 3 Epoxy

#5

Thanks Mike, I need to try RAKA next time

gil jones

>

Re: System 3 Epoxy

#6

Another way to thicken epoxy

Brian Hahn in SW Wisconsin

>This comes from the System 3 "Epoxy Book" (available on their web site) and gives a clear thickened epoxy. (Most fillers make the epoxy cloudy.)

Mix the resin with 1/3 of the hardener and let it react. After an hour or so the mixture will be thick, but it will never harden because it doesn't contain enough hardener. Now mix in the remaining 2/3 of the hardener. This will thin the mixture (lower its viscosity) and make it workable, but it isn't nearly as thin as the normal epoxy mix and you still have the normal open work time.

Re: System 3 Epoxy

#7

Thanks for the info

Tommy Holmes

>Thanks for information guys. and Mike thanks you for the link to RADA I'm going to give them a try. Their epoxy is much cheaper and I like the idea that it is a proven product.