Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Now I need to ruin a battery charger

Posts

Now I need to ruin a battery charger

#1

Steven Antonucci

Now I need to ruin a battery charger

steve antonucci

>Water Gap Woodturners hosted Graeme Priddle last night as a guest lecturer. He's teaching at Peter's Valley and graciously volunteered to "do something- whatever you want" for the group.

If you've never seen his work up close, it is simply incredible. The closer you get to it, the more you want to touch it. Layer after layer reveal themselves upon inspection. Not to be missed if you get a chance.

Graeme asked the group if we wanted to see a burning demo, and the consensus was "sure, why not?" He started by describing his need for amperage. No little handpieces for him. He uses a homemade handpiece that probably cost a dollar to make hooked up to a car battery charger! 10A of power +/-. The tip of his burner heated up so fast that when it touched wood, the wood squeaked like a mouse ("mousewood"- you had to be there!). He is a man after my own heart, with a complete DIY mentality.

He did some branding, mentioned our own Molly Winton (and showed your basketweave tip to the group), and generally answered questions about how and why he maked things. A good time was had by all.

On a personal note, I volunteered (and was voted by the membership, running unopposed) to be the club secretary. I now need to figure out what a club secretary is supposed to do, so I can start doing it...

Steven

Re: Now I need to ruin a battery charger

#2

Re: Now I need to ruin a battery charger

Don Orr

>Sounds like you had a good time Steve ! I got to see him at the Yankee Symposium last year and you're right about his burning system. I remember the squeaking and actual flames ! He also cleans the burning tip with a brass brush after each touch to the wood. He has a smooth pattern of work just sitting back comfortably with the work held on his knees. I was lucky to get one of his demo pieces. He said I was supposed to finish it but I can't bring myself to do anything to it. His work is fantastic ! I'm looking forward to see what his influence brings out in your work.

Re: Now I need to ruin a battery charger

#3

Re: Now I need to ruin a battery charger

john lucas

>Steve I believe he uses a lamp dimmer in there somewhere but I forget whether it is in line before or after the battery charger. Did you get that info? I want to try it since I have a lamp dimmer, battery charger ,and homemade burning handpiece.

Re: Now I need to ruin a battery charger

#4

Re: Now I need to ruin a battery charger

Don at Central Illinois

>Cany you get more info on how he hooked this up? I would like to try some burning, etc. and I have a battery charger. I never thought of using it.

Re: Now I need to ruin a battery charger

#5

Steven Antonucci

Warning: attempt at your own risk.

steve antonucci

>I neither condone, nor recommend that any of you try this. I will merely relay what I saw last night, which may not have all of the information you need to do this without incurring serious risk of personal injury via burns or shocks.

Disclaimer over.

His rig is very simple. He opens the charge and cuts the hot lead, which he then passed through a dimmer switch rated to handle the wattage. Big button, click on, turn the current up and down. Alternatively, he said that you could build an electrical extension with a dimmer inline and plug the charger in to achieve the same effect- varying the voltage. If this mystifies you, you should stop right here and not even consider doing this.

As far as the "burning end" of the charger goes, he cuts off the "jumper cable" ends and wires them to a set of terminals (Radio Shack) which have been screwed to a wooden stick. The stick is insulated with PVC conduit. The nichrome tips just get screwed into the terminal strips.

I know what he does, and how he does it. I may attempt it. If you are concerned at all about this procedure, do not attemmpt it. The current is enough to kill you, and the tip is at least 1400 degrees. Bad things can happen if you are not careful, and as Don explained, there is a flash fire every time you touch the wood. Use common sense, and if you don't have any, just move on to the next post...

Steven

P.S. Not aimed at anyone in particular, but I don't want to be accused of burning down someone's house or electrocuting their cats!

Re: Now I need to ruin a battery charger

#6

how did you know I was going after the cat :)

john lucas

>

Re: Now I need to ruin a battery charger

#7

Steven Antonucci

It wouldn't have read the same with lizard...

steve antonucci

>I just need to figure out a way to do it without hacking up my charger, just on the burning end...

I'm thinking a whip of some kind that I can temporarily insulate the two leads with in rubber/plastic material and some wire ties. Of course, I may never get to it...

A lot of smoke, so do it outdoors...

Steven

Re: Now I need to ruin a battery charger

#8

Re: Warning: attempt at your own risk.

Bob Macgregor

>This sounds more like you are putting together a DIY arc-welder!!

Hey, there's an idea for producing a hot tip!

Re: Now I need to ruin a battery charger

#9

Re: Now I need to ruin a battery charger

charlie belden

>Some details about Graeme Priddle's DIY Wood Vaporizor!

Use "banana plugs" not RCA or phono plugs. the former can handle 10 amps, the latter two aren't intended to carry that much.

Nichrome wire for Auto Electrical or any outfit that makes ceramic electrical kilns (pronounced kill - the "n" is silent - like the "p" in swimming). - 18 gauge NOT 20 gauge

Dimmer - Leviton 6681-IW - about $5 at Home Depot - goes on the 110VAC side of the battery charger. A variac will also work - but they're much larger than a lite dimmer - and heavier for higher amperages.

Battery charger - Napa Auto - 10 amp 6 & 12V

Sanding procedure 110, 150, 180, 320, 600 then steel wool (don't know why he skipped 240) Recomends what sounded like Astra brand sand paper - doesn't clog as fast when sanding green or soft woods. Also LOVES a special "etched" "sand paper" which is actually

not paper but on a thin plastic substrate - I think he said it was SANDVIC - and that it's

hard to come buy and expensive - but lasts a LONG TIME, doesn't load up easily and can be cleaned with a toothbrush.

DICK BLICK "Micro-Point black Archive Quality felt tip pen for touch up of branded/burned/scorched areas.

Also emphasized that if you plan on branding a piece with an oiled finish - make sure the finish is really, really, really, really dry.

That's all the notes I took about the details.

charlie belden

Re: Now I need to ruin a battery charger

#10

Great follow up !

Don Orr

>Thanks for the extra info Charlie. Very helpful.My notes were more on technique than technical data so I appreciate the details.

Re: Now I need to ruin a battery charger

#11

Steven Antonucci

Laying in bed last night...

steve antonucci

>I think I came up with a way to do this without cutting up a charger at all.

My thought was to follow his advice about wiring the dimmer in a box with a plug (to avoid putting it on the unit and cutting a hole or opening the charger). I would simply plug the charger in when necessary and have a variable current.

So, I thought why not on the business end too?

I'm thinking that I'd mount a board with two insulate car battery terminals to connect the jumpers to when necessary, and then run the pen from the terminals. 1 minute setup (one plug, two jumper connects). The board would be either clamped to a table or in a vise to make sure it didn't short.

It's on my list, and that's how I'll do it if I every do it...

Steven

Re: Now I need to ruin a battery charger

#12

Re: Great follow up !

charlie belden

>Forgot to add a CAVEAT about the battery charger - no "electronics" inside the box.

I think he meant "solid state electronics" - the little delicate stuff that monitors the charging and shuts things down when the battery's charged, not digital display and the like - they probably can get zapped easily.

Oh - BTW - though he makes carving with burs look easy, especially the roughing to basic shape burs - it ain't as simple as it appears because often you need to be cutting "up hill" into unsupported end grain - as I've discovered. And because to the shape of the piece and the carving, you can't just turn the piece over and be able to cut that area "down hill".

I now understand why he's a Burs Phreak (you did get a chance to look into his Burs Collections didn't you?)

That's the thing about the people who do amazing things and make it look so easy and effortless.

Someone asked him what one of his well known types of pieces sells for (tacky question).

"This one's about $4,000 in US dollars." - he replied without hesitation.

The person who asked the question followed up with "And how long did it take you to make?"

Without a moments hesitation - and with a wry smile - Graeme responded in his Kiwi accent - "About twelve years."

There was no follow up question!

Priddle, for all his layed back appearance, and easy going ways - comes prepared - for just about anything, which is why I really enjoyed his demo and the opportunity to hang out with him during the break and after the demo.