Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

How to drill a square hole?

Posts

How to drill a square hole?

#1

How to drill a square hole?

keith zimmerman, Normal IL

>I need to drill a square (actually, rectangular) hole through a piece of 1/2" walnut for the insertion of a cut nail. The point where the nail passes through the walnut will be visible on both sides.

I was thinking of drilling a pilot hole, then using a small file to make it the shape I need.

Anyone have any thoughts about other methods I could use to accomplish this?

keithz

Re: How to drill a square hole?

#2

Re: How to drill a square hole?

john lucas

>That is the exact method that I have used. A square nail will actually fit a round hole but could split the wood if it's going into a piece that is not thick. In that case I shape the hole first.

Re: How to drill a square hole?

#3

Re: How to drill a square hole?

Ron in Drums PA

>Square off the corners with a chisel

Re: How to drill a square hole?

#4

Re: How to drill a square hole?

Ron in Drums PA

>First drill a round hole

Re: How to drill a square hole?

#5

Re: How to drill a square hole?

Jerry McCaffrey

>Did that twice today with quarter inch steel plate, which I doubt is softer than walnut:) Round hole and square up with a square file.

Re: How to drill a square hole?

#6

Steven Antonucci

Burn it in

steve antonucci

>Assuming that you don't go with the round hole(first), square peg fitting thing, you can heat the nail up with a torch and burn the hole square.

Steven

Re: How to drill a square hole?

#7

Re: Burn it in

Colin Spencer

>Depending on how large the hole needs to be what about a mortice chisel for a drill press that will give you a perfectly square hole?

Re: How to drill a square hole?

#8

My cut nails are only 1/8" wide by 1/4"

john lucas

>That's why I recommended the files. I've used jewelers files to shape the holes because my smallest chisel is exactly 1/8" wide and it's just a hair too much for my cut nails.

A dremel with a longer bit works well. The holes don't have to be square just close enough that when you drive or push the nail in it won't split the wood. I'm assuming these are decorative. If not then simply drill a hole and drive them in. They will square up the hole themselves.

Re: How to drill a square hole?

#9

Dick Hines

Re: How to drill a square hole?

Dick Hines

>My dad had a big drill press that had thing that would cut square holes. It had a drill that went in theinjig that looked like 4 chisels hookes together. He had 4 sizes the best I can remember. I used to drill holes in every scrap wood I could get my hands on. Square holes! How cool was that!

Re: How to drill a square hole?

#10

Thanks for the responses

keith zimmerman, Normal IL

>The cut nails I'm using are #10 spikes to be used ornamentally to support a square bowl. The nails will be in each corners, approximately 1/2" from each edge. I am very concerned about the possibility of cracking since these are important design elements of the bowl.

Thanks for the suggestions. It sounds like I have a bit of filing to do.

keithz

Re: How to drill a square hole?

#11

Peter Charles Fagg (UK)

Re: How to drill a square hole?

Peter Charles Fagg (UK)

>Take the wood to a joiner/carpenter he/she usually has a morticer which cuts and drills square holes instantly.

I used one some time ago for cutting the rebates for door locks in the edge of doors, brilliant machine!

Peter.

Re: How to drill a square hole?

#12

Thanks. This is a wonderful solution, but...

keith zimmerman, Normal, IL

>it would probably take a very large cut nail.

Thanks for your suggestion. Actually, a square hole larger than for a cut nail would be easy to do.

Thanks to everyone for your suggestions.

keithz

Re: How to drill a square hole?

#13

Re: How to drill a square hole?

Don Evans

>Dick:

They are called mortising bits. There is actually a machine made just for them but any drill press works also.

Don