Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Problem with HFreight lathe

Posts

Problem with HFreight lathe

#1

Problem with HFreight lathe

ILYA ZAVORIN

>I have a cheap Harbor Freight lathe that I bought used. I turn on the patio so the lathe has been outside for more than 1 year, although covered with a large grill cover. It's been working OK, but has developed a problem recently. When I try to increase the speed by turning the lever, it actually slows down rather than speeds up. So the fastest speed I can get is the one at the lowest setting. Is this a matter of something simple like cleaning, or is this a sign of something more serious? Thanks much.

Re: Problem with HFreight lathe

#2

Re: Problem with HFreight lathe

Al Neighbors

>Ilya, it sounds like the HF lathe may have a Reeves Drive. I believe you need to give it a good cleaning and lubrication. One of the transition pulleys is stuck, so when you move the lever, you are either stretching the belt, or getting so much slack that it's not contacting the pulleys at all.

When one pulley widens, the other must close up; and vice versa. I think it just needs cleaning.

Re: Problem with HFreight lathe

#3

Re: Problem with HFreight lathe

elliott

>How do you go about cleaning and lube?

Re: Problem with HFreight lathe

#4

Re: Problem with HFreight lathe

Jeff Rich

>I agree with the cleaning and lube.

The very cheap grease that is put on these lathes tends to harden over time.

I have the same problem with VCRs at my job.

If you have the owners manual, there is a good parts break down.

BE CAREFUL with the split ring clips and the springs.

Clean all the old grease from the moving parts and put a good quality lube.

Also be careful with the pulley sections, they are cast aluminum.

After its cleaned and lubed, it will work pretty good.

I have also had to replace the gear lever assembly in one of my HF lathes. Mostly just belts though.

I hope this helps!

Re: Problem with HFreight lathe

#5

Re: Problem with HFreight lathe

Al Neighbors

>It's been a long time since I had my Old Griz with the Reeves Drive. But I never took it apart. All I did was blow the dust and dirt out of it, and wipe it down with a rag, using a sharpened dowel pin to get the rag into the tight spots. After getting everything wiped off as well as I could, I sprayed the moving parts with WD-40, and let that set for about10 minutes or so to penetrate and soak hard to clean places. Then I wiped everything down again. When I thought I had it clean, I used an Oiler with one of those long, thin, pull-out tubes to put a drop of oil on every place that was a moving part... down between the fingers on the pulleys, so the oil would go onto the shaft, and not where the belt would get oil on it.

It worked like new. Every time it got a little stiff, I did it again.

That's all I know to do.

Re: Problem with HFreight lathe

#6

Re: Problem with HFreight lathe

Ilya Zavorin

>Thanks! What would be an appropriate type of lube for the job?

Re: Problem with HFreight lathe

#7

Re: Problem with HFreight lathe

Don at Central Illinois

>I have a Delta with a Reeves drive and have had to repair it once or twice. Most Reeves drives are the same so you could go to the Delta website and download the schematic for a Delta VS (Reeves drive) and get a good idea of how to take it apart and, hopefully, put it back together. Not real hard, just takes patience. Good luck.

Re: Problem with HFreight lathe

#8

Re: Problem with HFreight lathe

Wilford Bickel

>I would just spray mine down with spray silicone. It would act as a solvent for the old grease and lube up everything. Then about once a month I would pop the top and spray it and keep turning.