Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

PM 3520a Problems

Posts

PM 3520a Problems

#1

PM 3520a Problems

RPE

>My 3520a quit running the other day. Jan 03 was when I purchased it. I shouldn't say it quit. It does run. It will turn on and accelerate, but when you turn the speed down with the Pot, it slows to a stop.

PM said it was the brake resistor. They sent one and it didn't fix it.

I do get a fault when it does this. It is "ou". PM says this is an over voltage fault. That is what the fault code means. I looked up the fault codes on line. I did check my voltage and it is 242 or so.

One guy at PM tried to tell me it was "the time of season when there is over production of electricity due to lack of use by consumers, so just hit the reset button".

These guys at PM don't have any idea. It is above their pay grades. They just sell parts. I have to pay for their guesses.

Does anyone know if a VFD is VFD? Do they have to be programmed? You can get one for $250 from Delta Electronics or pay $900 from PM.

Anyone out there had this type of problem?

RP

Re: PM 3520a Problems

#2

Jesper, Denmark

Re: PM 3520a Problems

Jesper, Denmark

>I assume you voltage should be 220 Volt. It is quite normal for the voltage to be plus or minus 10%, so the 242V is NOT the problem.

VFD's do need programming. Usually iot is setting some acceleration and braking parameters and a few other bits and pieces. I had to set the input frequency top 50 from 60 when I moved the General from North America to EU. General supplied a new set of parameters for the Square D Altivar they use.

If you can tell which VFD you have - call the manufacturer or get a manual on the net.

Re: PM 3520a Problems

#3

Re: PM 3520a Problems

Ron in Drums PA

>If your email worked I would have sent you a manual this morning

Re: PM 3520a Problems

#4

Re: PM 3520a Problems

john lucas

>They had the same problems with some of the PM3520 and 3520A's at the Craft Center where I teach. The problems was too much voltage. I don't remember what the campus technician did. I will ask when I see him but it might be a week because I'm involved in photographing a camp this week and won't get to the craft center.

Re: PM 3520a Problems

#5

Re: PM 3520a Problems

robo hippy

>I had mine for 8 years, and didn't have that problem. The frequency drive knob/unit was replaced because it was acting funny. When I would turn the knob, it would be slow to react, or it would do it in increments, rather than a smooth transition. When I replaced the unit, problem solved. I had heard that this was a problem after some years of use.

robo hippy

Re: PM 3520a Problems

#6

over-voltage on the DC bus...

Phil in NJ

>RP,

Please note the "over voltage" refers to the internal DC bus, not necessarily the line input. The line input tolerance as per the manual is 180v - 264v, so your 242v should be within specification as others have said. Assuming single-phase input here.

From the manual:

The AC drive detects that the DC bus

voltage has exceeded its maximum

allowable value.

1. Check whether the input voltage falls within

the rated AC drive input voltage.

2. Check for possible voltage transients.

3. Bus over-voltage may also be caused by

motor regeneration. Increase the decel time.

So I think it is possible that you are falling into category #3 here, where dynamic breaking is causing regeneration on the DC bus. Does the error code appear even when you run the lathe with nothing on the spindle?

You could certainly adjust the deceleration time to see if that's actually the problem. The faster the deceleration, the more power needs to be dissipated by the braking resistor.

-Phil

Re: PM 3520a Problems

#7

Re: over-voltage on the DC bus...

RPE

>The "ou" does not appear until the lathe starts to spin down to a stop. When the late is running, it shows the "freqs" or speed at which the lathe is turning.

I am not so sure of the voltage right now. I will have to check it again. It might have been 224.

The malfunction occurs with items on the spindle or not on the spindle.

Thanks

RP

Re: PM 3520a Problems

#8

Re: PM 3520a Problems

RPE

>Sorry, Just remove the "1" from the address.

Re: PM 3520a Problems

#9

Re: over-voltage on the DC bus...

RPE

>I just went and checked the voltage and it was 238.4

Re: PM 3520a Problems

#10

Re: over-voltage on the DC bus...

Phil in NJ

>That input voltage should be fine.

I would suggest

1) make sure your ground is really grounded, as a sanity check.

2) reset the deceleration value to something longer, and see if you can avoid the over voltage condition. The parameters are Pr.11 and Pr.13 I think (not sure exactly what model of drive you have?)

3) put a resistance meter across your braking resistor.

Re: PM 3520a Problems

#11

Re: PM 3520a Problems

robo hippy

>I had noticed with mine that with the factory set 5 second brake, that a number of times, especially if I was turning at high rpm, that if I used the variable speed knob to slow the lathe down, it would trip the reset button. If I slowed down very slowly, no problem, most of the time. I had the brake set to 8 seconds, and problem eliminated.

robo hippy

Re: PM 3520a Problems

#12

Re: PM 3520a Problems

RPE

>I talked with an "expert" from Delta Electronics who was extremely helpful. I will trouble shoot from the phone on Monday, 2 June. He is an engineer on the VFD-B at Delta Electronics. He is a woodworker also. He sounded excited to help. I will post an update.

RP

Re: PM 3520a Problems

#13

Re: PM 3520a Problems

RPE

>I thought I'd provide a little up date to my 3520a problems. Powermatic was eager to sell me parts that wouldn't fit my lathe. The sold me a new brake resistor that was for a 4224. The leads were too short and they admitted they no longer had the proper resistor for my lathe. It was the only resistor they carried now.

I contacted Delta Electronics, the maker of the VFD. An engineer for the VFD and also a woodworker was very willing to assist me. He spent hours on the phone with me trouble shooting the VFD. He told me that Powermatic was suppling inadaquate resistors with the lathes. Only by two ohms, but still inadequate. Powermatic provides 80 ohm resistor and the Delta design spec calls for 82 minimum.

The larger the resistor you have will accomodate the starting and stopping of the lathe, which creates heat and eventually damages the resistor (especially if it is too small). It dosen't matter if you use the on-off switch or the variable speed knob, you are decellerating the lathe which uses the resistor.

When you decell a DC motor it becomes a generator. The power then travels back to the VFD and can ruin it. The resistor absorbs this power and protects your VFD. I know my explaination might be a little simplistic for you EE's out there, but that is it basically.

He told me the larger resistor you have the better off you will be. It will protetct your VFD as well as last longer. I now have a 100 ohm, 500 watt resistor. It will not fit in the headstock. I have suspended it from the headstock on straps so it will travel when the headstock is moved. I had to get heat tolearant wire to run it to the VFD. I used solderless connectors at the resistor and the VFD.

I also needed a new board, not a new VFD, thank the Lord. Something happened, we don't know what, but my orginal board was bad, and was constantlly shutting off the lathe. It could have been caused by the resistor.

My 3520a is up and running again.

I'm not mad a Powermatic. I love my lathe and my PM 66 table saw. They are the best made in the USA.

Tech support at PM tried to help, but it is above their paygrade. and they wouldn't admit it. They just buy the parts from Delta and put them on their tools. They don't know how they work. They tried to be helpful. A few of them were just making stuff up, stuff that wasn't true.

You can find VFD's for $275 on the internet. PM wants, I beleive $990 or so for it. PM wanted $96 for the resistor. I got it for $50 (for the big one, the size PM sells was $27). Powermatic does reprogram a few of the factory defaults in the VFD. I will try to get a copy of the parameters that PM changes and keep them just in case someone else needs them. The main ones are the max freqs, and accel and decel times.

It pays to be persistant, and sometimes, you have to be smarter than the doctor.

Remove the "1" for email.

Re: PM 3520a Problems

#14

Re: PM 3520a Problems

Dick Coers

>"I'm not mad a Powermatic. I love my lathe and my PM 66 table saw. They are the best made in the USA."

I guess you have an older 66 saw, but your lathe is not made in the USA.