Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Wolverine Essential Upgrade!

Posts

Wolverine Essential Upgrade!

#1

Wolverine Essential Upgrade!

Jerry Hall

>Good find at the Utah Woodturning Symposium last week. I replaced the bunged up spring on my Wolverine, which also was twisted to one side from the repeated twisting force of tightening, with a slick bearing based add on. A new $11 product called "Sharp Fast" from TSI at Craft Supply. Not yet in their catalog, but in inventory. Works great, even fairly well where the flute ramps up on short tools, altho I am still grinding a flat for indexing the jig on short tools. I also locked the leg angle at 23 degrees as recommended by Kirk DeHeer of Craft Supply in the Winter 2006 AAW Journal. Have done this for a year. Gives an equal included angle with the flute all the way around the grind.


img

Re: Wolverine Essential Upgrade!

#2

Re: Wolverine Essential Upgrade!

Dave L

>Question--this may be evident, but I can't figure it out. How did you set the leg to 23 degrees? Do the notches represent angles in degrees? Or, did you somehow use a protractor to set the 23 degrees? Thanks in advance for your answer.

Dave

Re: Wolverine Essential Upgrade!

#3

Re: Wolverine Essential Upgrade!

Jerry Hall

>The top of the second notch according to the article is 23 degrees. I checked it with a General adjustable protractor, with the protractor leg cut to 3" so I can also more easily use it to check bevel angles on my tools. The top of the second notch put the center line of the leg dead on 23 degrees for me. The article is well worth digging up. There is a lot of other neat info, like a jig for setting the Wolverine arm to various repeatable bevel angles in the face of wear shrinking the diameter of the wheel. My setup is now very repeatable and I get by with one, maybe two sweeps and almost no metal removed. The fingernail jig has the upper machine screw threaded into the jig. I used an Allen wrench to lock the leg down tight and the secured it with the hex nut. I also put a lock nut on the second screw, where the wing nut was. I never move the leg after it has been set at 23 degrees. Kirk actually welded his at 23 degrees so students and demonstrators won't change it.

Re: Wolverine Essential Upgrade!

#4

He welded it?????

James McClure

>That's too funny. But it kind of defeats the purpose of an adjustable jig doesn't it? ;-)

Re: Wolverine Essential Upgrade!

#5

Re: He welded it?????

Jerry Hall

>As I understand his point in the article is that the ONLY thing adjusting the leg does is control the angle between the flute and the wing. He believes that most all professional turners he has watched hand grinding make this angle fairly constant all the way around, equaling the bevel angle at the point, so that you have a similar cutting experience (i.e. not "grabby") all the way around. Bottom line is he determined empirically that the 23 degree leg angle does the trick. And that is what he teaches at Craft Supply, and he doesn't want any students mucking with the angle. And I guarantee that they won't now that it is welded! He doesn't see any reason for a different leg angle. So far I agree. The Oneway instructions are incomprehensible to me, and provide no real rationale for leg angle. His article does. I am surprised his article has not generated comment and discussion. I would like to see that.

Re: Wolverine Essential Upgrade!

#6

Re: He welded it?????

Peter Hyde

>I have a problem with this concept. I understand the idea of keeping the angle at the tip the same all the way around the sides but...

different gouges have different flute profiles and sizes. So to maintain one correct angle on a variety of gouges that would mean adjusting the leg angle on the jig, which brings us back to the original design and the usage intended. So welding it and using the same set up on all gouges is totally ineffective unless you only have 1 gouge. My $0.02 FWIW

Re: Wolverine Essential Upgrade!

#7

Re: He welded it?????

Jerry Hall

>Good point, Peter! Maybe Kirk has an answer, I don't. I am fast approaching my level of incompetence I fear.

But I pulled out three of my 1/2" bowl gouges, each ground at 45 deg with the leg at 23 degrees:

Crown - Deep V flute short bevel

Sorby - Sort of a steep U medium length bevel

Thompson - Shallow flute U long bevel

Each of them end up at the top of the flute, and end of the wing, at about the same angle to my eye. It seems that the V flute just dives deeper, and results in a shorter bevel. When I look at the wings straight on, from the nose the angle between the flute and the wing looks close to the same for each of the tools, but there IS a little difference.

In looking at the article again I think what Kirk is trying to avoid is the common very acute angle on the wings which is the result of moving the leg to a higher angle. Perhaps 23 degrees is a good compromise for the different flute shapes.

In any case, looking at my three tools they seem to have very much the same wing angles in spite of the difference in flute profile. But there is no question that a continuous circular U shape (Thompson) gives a more consistent bevel angle than does the V shape (Crown.)

Re: Wolverine Essential Upgrade!

#8

Re: He welded it?????

Peter Hyde

>Mmmm. I grind bowl gouges at 60� and find that your 23� angle on the leg means the tool is dangerously near the center line on an 8" wheel.

I also have 3/8"- 5/8" gouges with really varying flute shapes from almost semi-circular to acute V and combined with the different sizes there is no way that angle can be constant. I did do a grind with the leg set at 23� and the wings end up almost at 90� to the edge of the V flute on a 1/2" gouge. I haven't used it yet so I can't comment on it's effectiveness. Interesting, very interesting. :-)

Re: Wolverine Essential Upgrade!

#9

60 Degrees and Dangerous

Jerry Hall

>Peter,

Attached is a picture of a 65 degree ground, steep "U", 5/8 gouge at the grinder with a 23 degree leg. I am near the centerline but not dangerously close in my opinion. I have, per the article, set the wheel centerline 6" up from the seat of the arm. If it was less I would move to "dangerous" for sure. But 6" is ok with me up to maybe 75 degrees. More than that I could simply put a temp wooden riser of perhaps a 1/2 in the seat. I wouldn't monkey with the leg angle, altho steepening the angle a bit would probably do it fine.

By eye I guess the included angle (bevel to flute) of the wing varies from 45 deg at the end of the fingernail to the measured 65 at the nose. Clearly not equal as you say, but not acute either. I can't imagine 90 deg.


img

Re: Wolverine Essential Upgrade!

#10

65 degree grind 

Jerry Hall

>


img