Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Slightly OT: Anvil Follow-up

Posts

Slightly OT: Anvil Follow-up

#1

Steven Antonucci

Slightly OT: Anvil Follow-up

steve antonucci

>So, I found a guy locally who blacksmiths, and he sells excess equipment. Really nice guy, consults to budding smiths to make sure that they know what they are buying and that they don't overbuy...

I went over to his shop a few weeks back, and turns out he is a knife maker (I've also made a few). He showed me a couple of damascus blanks that he's working on, and we got to talking about how he finished the handles.

"I just use some walnut"

I recoil in horror.

"Plain walnut?"

"Yeah"

A trade is born. He's got the perfect starter anvil for someone like me. An old section of railroad tie. In return, he's going to get a box of wood cuttoffs that will open his eyes to the fact that there is better material than walnut.

I took an old cutting horse that I made years ago (never put the screws where a chainsaw will be cutting!) and turned it into my anvil bench. If you look closely, you'll see two slabs of walnut under it that I drove the 4 railroad spikes into. 3/4" thick and they didn't split it.

(a free tip: When you slab out the pith for bowl blanks, slab off either side of the pith into these sections and just stack them up. They are almost 100% quartersawn and make excellent handle materials)

Almost a perfect height for me, too high for my 10 year old...

Steven


img

Re: Slightly OT: Anvil Follow-up

#2

Re: Slightly OT: Anvil Follow-up

John K Jordan

>Old railroad rails make wonderful small anvils - I have two. I made one with a pointed horn, shaped the foot, and flattened the face so it's more like a "traditional" anvil. I have another that's just a section of rail that's also useful. My farrier also carries one made from rail on his truck when he shoes horses. I have a 5' section of rail behind the barn for making more when I get time, and for exactly the reason you discovered - for trading! Everyone wants something for whacking! (For the most efficient whacking, the anvil height should probably be at about the bottom of the natural hammer stroke for your height.)

BTW, if you decide to cut off a piece of railroad rail and/or shape it with a torch, be careful! It's possible (I did it with a relatively small torch) but the steel is so thick you have to "scoop" out puddles of steel a little at a time which tends to blow molten steel all over the place. I've got some embedded in my boots.

One thing I don't understand is your comment concerning the quartersawn slabs for handle materials. Since both knife and turning tool handles are relatively small, how does the orientation of the slab matter for either unless the board is cut very thin for knife handles? A round handle turned from flatsawn stock will be identical to one made from quartersawn.

Hey, you've found the secret of making a knifemaker into a friend for life. They can use thin strips that are useless for turning. I save offcuts sliced from exotics like cocobolo for a knife guy I know.

JKJ

Re: Slightly OT: Anvil Follow-up

#3

Steven Antonucci

Re: QTRSWN wood...

steve antonucci

>I use the quartersawn wood to make handles because for the most part it doesn't move at all. Even if it is turned wet. At 2+ years to dry to EMC, I just throw them in a pile in the shed without regard to stickers etc... If they fail, they're firewood, otherwise, free handles. Turned wet or dry, never had one fail...

While I can get KD wood for handles, it's nice to have a use for the free stuff.

Steven

Re: Slightly OT: Anvil Follow-up

#4

Re: Slightly OT: Anvil Follow-up

john lucas

>Steve I don't have a good anvil yet. A couple of odds and ends that I fabricated and a cast cheapie. I have a friend who is a blacksmith and he was making laminated wood handles. There were very poorly done so I made him some laminated blanks with really fun patterns.

Re: Slightly OT: Anvil Follow-up

#5

Steven Antonucci

Maybe I can make my own coring tool?

steve antonucci

>Or have him make one? Seems easy enough to handle if you've got the steel and the tools...

For sure, I can see some tool rests in the future :-)

Steve