Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Wheels on a 3520?

Posts

Wheels on a 3520?

#1

Wheels on a 3520?

Steve in NC

>Hey Folks

I have had my PM 3520 for about 6 months and I am thinking about rearranging my shop to take advantage of being able to turn of the end. The best location for the lathe would partially block access to the 35 gal drum I use as a 1st stage for my dust collector.

I only have to empty the drum once a month or so but the lathe would have to move to get to it.

I have seen quality casters that have a stud mount and 250 lb capacity. They also have a lock that holds both axixs of rotation.

Has anyone ever mounted their lathe on wheels. (height will not be a problem) With the PM's mass and speed control, I rarely get significant vibration so it seems like it should work.

Steve

Re: Wheels on a 3520?

#2

Re: Wheels on a 3520?

John K Jordan

>Steve,

I don't know about wheels, but the local Woodcraft has a moves a lathe regularly with a palette jack. These are pretty cheap at places like Northern Tool. Of course, you would have to create some supporting frame but that should be fairly simple, especially if welded up from steel. The frame could be fit under the legs if you needed to raise the lathe a bit anyway, or could be made to lift from higher on the frame.

Also, I once bought equipment casters that mounted on the side of a leg and didn't touch the floor until engaged with a foot lever. That might work fine for occasional use and would leave the legs firmly on the floor during use.

JKJ

Re: Wheels on a 3520?

#3

Steven Antonucci

I wouldn't make it "permanent"

steve antonucci

>I've seen people mount the wheels so that they can be lowered when things need to move, and raised when the lathe is in it's resting spot. This gives you mobility without introducing vibration.

Search the Turning board and you should be able to find something that works for you.

Steven

Re: Wheels on a 3520?

#4

Steven Antonucci

Now cut that out!!

steve antonucci

>Yesterday, you did it to me.

Today I did it to you. Same post, same time. You hit enter first...

Steven

Re: Wheels on a 3520?

#5

Re: Wheels on a 3520? *LINK*

Peter Teubel

>I use the Woodcraft mobile base kits on all my stationary equipment including my 600lb bandsaw. I don't bother with the plywood base. I just bolt (or weld) the mobile base "corners" to the machine. When popped down on the "legs", my 1224 is extremely stable. Can't even tell its on a mobile base. My big lathe (2436) is the only machine not mobile, because its going to be bolted down soon.


Woodcraft mobile base kit

Re: Wheels on a 3520?

#6

JL

Re: Wheels on a 3520? *LINK*

JL

>I've been toying with the idea of putting these guys on a machine or two.


Great Lakes Swivel Casters

Re: Wheels on a 3520?

#7

Re: Wheels on a 3520?

Curly Smith

>There's really no difference in having your lathe sit on 4 locking casters or on 4 feet, provided the casters can support the weight. As you likely already know, Woodcraft currently has their 300# rated casters on sale (http://www.woodcraft.com/family.aspx?FamilyId=1989).

Re: Wheels on a 3520?

#8

Re: Wheels on a 3520?

john lucas

>I have to respectfully disagree. There has to be some flex in a caster system especially if it swivels. I can't believe it would be as solid as a machine sitting on the floor. Especially with an out of balance piece trying to walk the machine across the floor. My metal lathe is currently set up with permanent casters because it has to be moved once a month for our club meetings. It is amazing how much vibration is created this way.

I built a set of wheels that can be placed under the machine after I lift it with a hydraulic scissor jack. I lift each end and put the wheels underneath, then lower it back down to lock the wheels in place. When I'm finished moving the machine I simply jack it up and remove them. Mine are wooden with some metal bracing but I plan to make a steel caster set in the near future.

One good system I saw was to put the caster on permanently and then have a seperate threaded bolt type jacking system attached to the legs so you take a socket wrench and lower the bolt until it removes the weight from the casters and levels the lathe. I believe it was the club in Birmingham who did this on a Vicmarc 300 lathe. Very effective and easy to build.

Re: Wheels on a 3520?

#9

Look Interesting

Stuart Johnson

>These look interesting. Be sure to post a review if you decide on giving them a try.

Re: Wheels on a 3520?

#10

Re: Wheels on a 3520?

Mike in Suwanee

>Wm Redmond & Sons had a protype wheel system mounted on a Powermatic at the Southern States Symposium that was very slick. Foot operated to lift and lower the casters and rests on standard legs when casters lifted. Kind of pricey at about $280 as I recall but very solid.

Re: Wheels on a 3520?

#11

You're absolutely right

Curly Smith

>I completely forgot about the minor rotational aspect that these casters have when locked. Unfortunately, in this application that "minor" detail would likely be a major problem. It's one thing to walk away from your lathe, it's something else when your lathe walks away from you.

Re: Wheels on a 3520?

#12

Chasing your lathe could be aerobic :)

john lucas

>

Re: Wheels on a 3520?

#13

Re: Wheels on a 3520?

John Kyler

>I move my 4224 (900lbs)around the shop using an ATV and the nylon feet it came with.

I have used lathes with casters and would advise against it.

It only takes a very small bit of movement and the lathe will rock and change the tool approach as to your stance.

Re: Wheels on a 3520?

#14

Re: Wheels on a 3520? *LINK*

John Peck

>One solution, posted on other forums, is to use a hydraulic lift table cart, such as the one available shown here - http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=41145 -- to move the Powermatic 3520 lathe.


HF Hydraulic Lift Table Cart

Re: Wheels on a 3520?

#15

Re: Wheels on a 3520?

tim mathis

>hi steve,i made a stand and bolted my 3520b to it.i use zambus casters #ac 600. they are rated at 2600#.the great lakes casters are similar to them.they could be mounted to the legs after you redrill the holes. the way i made the stand the casters raised the lathe 1 1/2 inches , my mat that i stand on is 3/4 inch so it is only really raised 3/4 inch. a poster on another forum compared his great lakes and his zambus casters. in short the zambus were larger, heaver made and the pads were easier to work but the zambus do cost more. i went with the zambus casters( i did not want to have a failure while turning)the pads are larger than the stock feet the lathe comes with.when the pads are down the lathe acts as if it was on the floor.it rolls easy and the pads are easy to put up or down . it is quick and easy to level it.i made my stand wider and longer than the lathes footprint. i have over 900# rolling on my casters( the stand weights about 100# , 2 full cabnets , and racks for extra tool rests. i have tried to post pictures but i am doing something wrong. to see photo's check my name over at the creek.

Re: Wheels on a 3520?

#16

Don't forget to use caster oil :)

Mike Jones, Redding, CA

>

Re: Wheels on a 3520?

#17

Casters can raise your lathe too high...

Jerry Hall

>As I have found as I have shrunk from 73" to less than 71" over the years....And the 3520 is just about elbow height for me with the standard feet. So a buddy and I designed the bracket in the photo below with high quality casters and sturdy feet from MSC. It allows the Mustard Monster to be at the lowest possible height need be. He used his on a the 16" Jet. Also some other ideas in this link:

http://docs.google.com/View?docID=d4b7vjd_19f4xnj9&revision=_latest

We paid for the materials and welding, probable ended up $40 per foot. If your handy you could do it for less. Lots of hole drilling and fitting in the legs. Works well and I soon got used to stepping around it. Does make for a wider stance which is good on my big green rough outs. I move it out and back easily for demos when our Chapter meets at my shop.


img