Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Sealing end grain of fresh cut logs

Posts

Sealing end grain of fresh cut logs

#1

Sealing end grain of fresh cut logs

Warren Chernoff

>okay guys, what do I use to seal the end grain of freshly cut logs to help prevent checking. I'm not looking for anything fancy nor expensive, just something that works and is reasonbly inexpensive.

Re: Sealing end grain of fresh cut logs

#2

Jesper, Denmark

Re: Sealing end grain of fresh cut logs

Jesper, Denmark

>The definitive answer is Anchorseal - OK if you need to do a lot. If it is just a few logs, any old latex paint works.

Re: Sealing end grain of fresh cut logs

#3

Re: Sealing end grain of fresh cut logs

John K Jordan

>You can find Anchorseal by the gallon at Woodcraft. It's cheaper if you buy a larger quantity direct from UC Coatings. I once bought a 55 gal drum but they also sell in 5 gal buckets. There are other similar sealers that might be less expensive or more readily available in your area.

Anything that stops or slows the moisture loss through the end will work. Anchorseal is just wax in an emulsion. Some people melt paraffin and brush or dip the ends. Paint will supposedly work, although perhaps not as well as sealer. I've read of people using roofing tar but that sounds messy.

Here are some comments on the Wood Web:

http://www.woodweb.com/knowledge_base/Wax_to_Seal_Turning_Blocks.html

http://www.woodweb.com/knowledge_base/Sealing_Log_Ends.html

http://www.woodweb.com/knowledge_base/A_good_cheap_end_sealant.html

JKJ

Re: Sealing end grain of fresh cut logs

#4

Re: Sealing end grain of fresh cut logs

Brian Hahn in SW Wisconsin

>Wax works the best. AnchorSeal is a popular wax emulsion. A furniture paste wax works (i.e. Johnson paste wax), but it might have trouble sticking to wet wood. You can make your own with paraffin and mineral spirits. I've also used melted paraffin, but it is harder to apply.

Second best is shellac. Apply several coats.

Latex paint and primer also work. Several coats work better.

I've tried a variety of other methods, but the results haven't been nearly as good.

I now use AnchorSeal for end grain and shellac for side grain.

Re: Sealing end grain of fresh cut logs

#5

Re: Sealing end grain of fresh cut logs

Ralph Watts

>Brian,

Yep, anchor seal is the best, however, no sealing of end grain will keep a log much longer than about a year, depending on conditions. I'm going through my wood stash (logs sitting in the dry for about 2 to 4 years and most of them are going to be firewood. Far better to process the green wood into blanks asap. Taking the bark off of large chunks and completely sealing the outside with anchor seal will maximize longevity.

Best regards, Ralph

Re: Sealing end grain of fresh cut logs

#6

Re: Sealing end grain of fresh cut logs

john lucas

>I have to store my logs in the driveway out in the sun. As near as I can tell no endgrain sealer I've tried saves them for very long. Anchorseal has been as good as anything and a heck of lot less mess than trying to wax the ends. You do need to seal the ends but I think storing the wood out of direct sun is probably one of the best things to do.

Re: Sealing end grain of fresh cut logs

#7

Re: Sealing end grain of fresh cut logs

Greg in Oshkosh

>Don't forget plastic trash bags. Keeps wet wood for a long time but may incourage spalting

Re: Sealing end grain of fresh cut logs

#8

I've been too chicken to ask

GolfSteve in Calgary

>I stumbled across a poor old polar cut into chunks. I took home a few pieces of crotchwood and rough cut them into blanks on the weekend. There's some nice grain in there.

Since I didn't have any wax or log end sealer I just put the pieces into garbage bags and they're sitting on my back step.

How long can I keep them like that?

I'd like to encourage some spalting. Anything I can do? Perhaps my snotty nosed kid can donate some bacteria and/or fungus to the blanks.

I bought some wax sealer today. I'll probably paint the blanks tonight.

I won't have time to rough out any bowls or platters until probably next week, and even then it will take me a week to do the roughing on all of the pieces.

Thanks,

Steven

Re: Sealing end grain of fresh cut logs

#9

Steven Antonucci

Spalting is easy...put them on the ground.

steve antonucci

>But you need to watch them, or they get mushy.

Steven

Re: Sealing end grain of fresh cut logs

#10

Miracle Grow and Beer

Stuart Johnson

>will cause spalting according to Jamie. Try sprinkling a half cup of each over the wood and reseal the garbage bag. Check it from time to time.

Re: Sealing end grain of fresh cut logs

#11

Day late, and a dollar short...

Allen Neighbors

>but old latex paint will work okay if you put on two or three coats.

Old oil based paint will work if you put on a decently thick coat.

Some of my Australian friends use paraffin that they melt and paint on. It's as good as anchorseal.

I've used old wood glue that had frozen and sat up and got thick on me.

I'm out of suggestions.

Re: Sealing end grain of fresh cut logs

#12

Re: Spalting is easy...put them on the ground.

GolfSteve in Calgary

>Do you put them on the ground after sealing the ends?

Re: Sealing end grain of fresh cut logs

#13

Steven Antonucci

No, before.

steve antonucci

>Make sure you flip it too. Or you end up with spalting on the top and mush on the bottom or spalting on the bottom and nothing on the top.

S

Re: Sealing end grain of fresh cut logs

#14

Re: Sealing end grain of fresh cut logs

jim miles- Charlotte

>Remember: You are not trying to " seal" the end grain. You want it to dry out, you are trying to slow the process to equalize the moisture loss from end and the sides. Whatever you use is eventually going to wind up on the shop floor as waste. My preference is miss tinted latex paint from Lowe's - $5.00 or less a gallon it does take 2 - 3 coats

Re: Sealing end grain of fresh cut logs

#15

Re: Sealing end grain of fresh cut logs

John K Jordan

>>...equalize the moisture loss from end and the sides.

Seems like that is IF you want it to dry which makes more sense with boards than large turning blanks or logs (the subject here). It may take many years to dry a log or log section.

If you want to preserve a turning blank, sealing it completely will keep it "green" and prevent end grain checks and cracks as long as possible, especially if kept cool. Logs recovered from even many years of submersion in water are often in good shape.

JKJ