Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Jet 1642 HELP

Posts

Jet 1642 HELP

#1

Jet 1642 HELP

John Packett

>I've lurked here for a long time but this is my 1st post. Not a turner yet but decided to take the plunge. Picked up my new 1642 last weekend and put it together today. Everything went well until I pluged it in and started it. It trips the GFI. The same GFI circuit works well with a CSMS, table saw, or planer, and other tools. I ran an ext. cord and tried it on a non GFI and it works fine. One other thing, with it plugged in and turned off the display reads zero. Is it normal for the display to be on 24/7 with the lathe turned off but plugged in.

Thanks for any help you can give.

Re: Jet 1642 HELP

#2

Re: Jet 1642 HELP

Bill Howatt

>I don't run my General on a GFI so I don't have any direct experience with it but I have heard that inverter VFDs will trip GFIs. It only takes about 0.005A imbalance in the 2 leads to cause a trip so it could be something in the circuitry that is draining a little current to ground - don't really know. I have also heard or this being a problem with computer switching power supplies which are very loosly related to how a VFD generates its power.

Some other Jet owner will have to tell you about the display issue but on my General when I press the Off button it just drops out a relay that removes the 24V generated by the VFD from the control circuity. The VFD remains powered up in idle mode. My feeling is that electronic stuff is happier powered up and idling rather than being shocked with on/off power-cycles. Anybody is free to disagree with this but it is the way I see it based on a bit of experience. I do unplug the lathe when thunderstorms are in the area though!

Bill

Re: Jet 1642 HELP

#3

Re: Jet 1642 HELP

Jeff Rich

>I wired a direct outlet for my 1642, 220v.

It is normal for the inverter to have a display.

I would have to agree with Bill on the GFI tripping.

Re: Jet 1642 HELP

#4

Ric Taylor

Re: Jet 1642 HELP

Ric Taylor

>John,

I'm not an electrician, but I have a Jet 1642 also, and I had the same trouble for awhile. Then I heard on this forum quite some time ago that variable-speed motors and GFI circuits don't get along very well. Plug your lathe into a regular outlet (non-GFI) and your trouble should go away. It worked for me.

Ric

Re: Jet 1642 HELP

#5

Re: Jet 1642 HELP

Mike Cunningham

>John,

What they said plus.......you mentioned using an extension cord, if you continue that practice make sure it's heavy duty, enough to carry the load properly otherwise you'll do in the motor.

Mike

Re: Jet 1642 HELP

#6

Same here...

Peter Teubel

>Same issue with my Oneways. They won't work on a GFI circuit.

Re: Jet 1642 HELP

#7

JL

Re: Jet 1642 HELP

JL

>I usually unplug my lathe when not in use - so I don't worry about the display light :). The reason why I unplug it is that I had a friend whose lathe got "fried" by a lightening strike - and I'm too cheap to buy a suitable surge protector.

Re: Jet 1642 HELP

#8

Thanks to all of you

John Packett

>It looks like I'll be running a new line with a disconect.

Re: Jet 1642 HELP

#9

Re: Jet 1642 HELP

John Uteck

>Same problem I had with my 1642 -- I had wired a new dedicated GFCI line for mine, and ended up swapping out the breaker. Has worked fine ever since.