Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Need advice on finish

Posts

Need advice on finish

#1

Need advice on finish

ILYA ZAVORIN

>I turned a piece of cherry that included the pith. Haven't sanded it yet. I think this is a type of flowering cherry, the hardwood is creamy in color and the sapwood is almost white. Since the pith had small cracks in it, I applied CA glue to it. The glue penetrated the walls of the bowl all the way through and came out on the inside. As expected, it also stained the wood noticeably. This means that no matter how much I sand, I won't be able to remove the stains completely. So my question is: what type of finish should I apply that is dark enough to hide the CA stains but still light enough not to hide all the grain? If that's not possible, I would prefer a darker finish to cover the stains. So far the only type of finish I've used has been salad bowl finish which, clearly, would not work in this case. Thanks.

Re: Need advice on finish

#2

Re: Need advice on finish

Wally Dickerman in Arizona

>If you apply a dark stain you'll hide the pretty color of the cherry. Because the soaked-in glue won't accept a finsh you won't be able to hide the glue stain anyway. Why not use some sort of texturing in the glued area?

There is a saying that I like...Make your mistakes look like that's what you intended to do in the first place.

Wally

Re: Need advice on finish

#3

Re: Need advice on finish

Steve in NC

>If it is not too large, coat the whole bowl with CA. I have done this with boxes and it buffs nicely.

Steve

Re: Need advice on finish

#4

Re: Need advice on finish

GaryG in MD

>Hi Ilya,

I think you'll find that a typical oil finish, like Watco or your Salad Bowl finish, will darken the heart wood in almost the exact same way that the CA did. Put a few drops of oil around the CA'd area to test it -- wait a few days for the oil to dry and then sand the area lightly. I'll bet you won't be able to see very much difference.

...Gary

Re: Need advice on finish

#5

Re: Need advice on finish

Sean Troy

>Unless the turning is extremly thin, you can sand out CA glue stains no problem. Just takes a little longer than wood without the CA.

Re: Need advice on finish

#6

Re: Need advice on finish

Bill Neddow

>Wally, an old master crxaftsman I once knew put it this way: "It does not matter how good you are. What really matters is how well you recover from your mistakes."

Re: Need advice on finish

#7

Ric Taylor

Re: Need advice on finish

Ric Taylor

>Since the CA penetrated all the way through the wood, the stain will be visible all the way through the wood. No amount of sanding will get rid of it.

If you have this situation again, you can seal the wood surface first with some thinned lacquer. After the lacquer has dried, apply the CA. After the CA has dried, sand away the lacquer and the crack will have been filled with CA, but with no stains. The lacquer prevents the CA from penetrating into the wood.

Ric

Re: Need advice on finish

#8

Re: For future reference, the trick to .....

Jamie Donaldson

>... make CA glue lines invisable is to first wipe on a coat of lacquer thinned with a small amount of acetone in the area to be glued. This reduces the bleeding by capillary action of thin CA into the area around the glue application, and keeps the glue where you want it. I often use this same thinned lacquer as both sanding sealer and base coat prep for later finish application.

Re: Need advice on finish

#9

Re:Hey Ric- there's an echo in here!!!!

Jamie Donaldson

>

Re: Need advice on finish

#10

Dick Hines

Re: Need advice on finish

Dick Hines

>I try not to use CA on any of my turnings when I an getting down to the fine sand paper. If a crack developes I will whipe a coat of Watco over the crack and then apply the CA. Most of the time this will keep the CA from staining the wood. You will notice I said "most of the time".

Re: Need advice on finish

#11

Re: Need advice on finish

Wally Dickerman in Arizona

>If it's end grain the CA will soak in even with the oil.

Wally