Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Chainsaw Gas

Posts

Chainsaw Gas

#1

Chainsaw Gas

Barbara Gill, Remlik VA

>We recently had to buy a new weed eater. We were cautioned not to use regular gas in the oil/gas mix. They recommended either the mid grade or high grade gas. This also applies to chainsaws. Apparently the regular gas has become so bad that it is causing problems with chainsaws, weed eaters and any other piece of equipment that uses the oil/gas mix.

Along the same lines but off topic, our mechanic said he is seeing fuel filters having to be changed more often because of the quality of the regular gas.

Re: Chainsaw Gas

#2

Re: Chainsaw Gas

Bill Neddow

>Another problem in our area is that the provincial government has decreed that all of the low grade gases have up to 10 per cent ethanol added. The better chain saws do not like that. Had a $600 rebuild on my Stihl 660 last fall because it is built so well it did not have the "slop" in the cylinder to absorb the extra heat.

Re: Chainsaw Gas

#3

Re: Chainsaw Gas

Fog Tanner

>You can thank the EPA for that. Has nothing to do with the tolerances of the saw. I run tighter tolerance 2 cycles on 70+% nitro with no problems. I also have some others that run only alcohol and oil. Its all in the mixture setting in the carb/injector. My Stihl came from the factory borderline lean, and in warm weather air (90s) it was lean. In the winter (60s) when the air was denser, it was close to right. That was on gasoline with no alcohol. But it was so bad I was on the verge of dumping the nitro mix in and run it till it dropped or kicked a rod.

I talked to the factory rep and found that the EPA mandiates the mixtures setting for the saws to run hot. Some EPA mental giant believes that will reduce emmisons, which is really doesn't. The factory rep told me that if it were richened up, it would run better, last longer and make more power. But, per the EPA there are stops on the carb adjustments to limit the mixture setting to lean. Once these are removed, it can be richened up to where it should be. I also asked about the 10% alcohol fuels and was told that was no problem if they were adjusted correctly.

My saw now runs well in the summer, and I am having to use the 10% stuff. The EPA settings and stops are history and the saw has more power and actually starts like their ads say it will. You can either adjust it or find a shop that knows what they are doing and will adjust the engine the way it should be and not the factory EPA settings. There was a response in a thread a year ago or so that had a very good step by step procedure for setting your mixture.

Fog

Re: Chainsaw Gas

#4

Re: Chainsaw Gas

Mike Brazeau

>Stihl actually have recommended 89 octane for some time. Have had a Stihl saw for ten years and never noticed it until I bought one of their trimmers and read the manual. Now use in both.

Re: Chainsaw Gas

#5

Re: Chainsaw Gas

Bill Crommett

>Years ago a petroleum chemist said on one of the forums ( I think it may have been Badger Pond ) that regular gasoline was produced by "Dirty Technology" and that it would gum up an engine quicker than premium. Since that time I have used nothing but premium gasoline in all my outdoor equipment, both 2 and 4 cycle. Some of the engines sit for months with out running and still start up and run like they had been used three days ago. Conclusion: Small engine fuel is no place to economize.

Re: Chainsaw Gas

#6

Re: Chainsaw Gas

Texian

>New chainsaw and leaf blower manuals suggest 89 octane gas, so have switched to that for all small engine fuel. Also suggest use of Sta-bil or other fuel stabilizer for all small engine fuel, all year round. I add it to fuel container as soon as I get home, so do not have to remember if I did it. All year, as unknown when next chainsaw usage will be, or when grass will stop growing.

Re: Chainsaw Gas

#7

Jesper, Denmark

Quality myth......

Jesper, Denmark

>Gasoline is gasoline---- there are no "quality" differences between regular and high octane other than the octane rating. The gas comes of the same distillation towers in the refinery. The additives are blended in later, so the basic "quality" and cleanliness is the same.

You get nothing from running a higher octane than the engine needs - except maybe a lighter wallet.

If the engine does not ping with the lower octane rating, it does not need higher octane gas.

Higher octane does not run better at lean burn settings than lower octane.

The 10% ethanol only makes the food grains more expensive - it will not hurt your engine.

Re: Chainsaw Gas

#8

Jesper, Denmark

Re: Check this out.......

Jesper, Denmark

>http://www.state.mn.us/mn/externalDocs/Commerce/Gasoline_Octane_Facts_102902052227_OctaneFacts.pdf

Re: Chainsaw Gas

#9

Old Report

Barbara Gill, Remlik VA

>That report was dated 2004. I would think that possibly whatever is affecting the fuel filters in motor vehicles now was not an issue 4 years ago.

Re: Chainsaw Gas

#10

Jesper, Denmark

Re: Old Report

Jesper, Denmark

>Hi Barbara,

The petroleum refining industry has not changed that much in the last 4 years. Particularly not in the USA, where no new refinery has been built for many years. I even think the last grass roots refinery wad the then Mobil refinery in Kankakee, IL, when I lived there - in the 70 and 80's.

All that has happened since has been quality improvements in terms of reducing sulfur and getting rid of first tetraethyl lead and since MTBE and adding ethanol. I am not aware of "the fuel filter problem" it does not exist here in Europe. Probably the higher solvency of the added ethanol is cleaning out crud in the tank, depositing this in the filter.

It does not have any effect on the basic question: Higher octane gas ONLY helps if the engine pings. If it does not, then "High Test" is no better quality than regular.

Pinging is not usually a problem with small engines. If you check the engine specifications, it probably has a compression ratio around 9 - absolutely no problem with regular gas.

Incidentally, our gas is no better quality, although we end up paying $8/gallon. One the other hand, Diesel quality is very good at <7/gallon, so as it has more energy per gallon than gas and the engines are more efficient, that is what people now buy.

Re: Chainsaw Gas

#11

Re: Chainsaw Gas

Curly Smith

>I wonder if the ethanol is compatible with the hoses and plastic parts. My experience is that fuel lines don't last very long on the yard tools (2 years max) and that they tend to crumble. I also wonder if the anti-corrosion agents added to the ethanol don't gum-up the works.

But, back to Fog Tanner's point, if the equipment is set to run lean on low octane fuel (and they are, you really should remove the stops) then higher octane fuel will make it easier to start - and you know the stores don't want you coming back with a grass trimmer that won't start. I do wonder how much can be actually blamed on the EPA... if they're running lean then they're running hot which greatly shortens the life which makes you buy replacement. The EPA mandated the emissions standards, the manufacturers chose how to meet the standards.

Re: Chainsaw Gas

#12

Re: Quality myth......

Barry Irby

>I watched a show on TV about gasoline. (So we KNOW it must be the absolute truth, Right?). It was interesting. They went back through the history of it and how it started with about 10 octane. WWII made a big impact on the chemistry and they had to get more gas from a barrel and more octane for the fighters and bombers. ON and On, but interesting. At the end, they pointed out that The refineries are jointly owned or owned by others, not necessarily the fuel companies. All of them share the use of the refineries and the pipelines. They treat it a fungible commodity. Exxon or whoever puts a ship load of crude in on the gulf coast and they are credited with the amount of product it will produce at the other end of the pipe line. All the gasoline they produce is identical and remains I identical until it comes out of the pipe at the terminal or storage facility. At that point, the company that owns it adds their additives and tries to convince us that their gas is better than those other guy's. I truth, they have no idea where the gas came from or who brought it here. They did not address the various grades, but my understanding was that that was a difference in the additives, not the gas itself.

I don't have a goldfish in this bowl, but wouldn't it be nice to be able to get straight answers without all the misdirection and mystery? For example, you keep hearing "we have not built a new refinery in this country since the 70's", making it sound like we have no new refining capacity. Not true. They have doubled and tripled the size of some of the ones we have. We have huge new capacity, just not new locations.

If running my chainsaw or any other small equipment or even my car on mid grade would make it run better or last longer, I would be right there, but I am not enough of a mechanic or petro Engineer to sort the hype out of the truth. I do know that I ran my Honda CRV on what ever regular gas came out of the pump, any pump with no brand loyalty at all and got 280,000 miles out of the engine on three sets of spark plugs, with no issues with the engine. We sold it and I bet it is still going.

Re: Chainsaw Gas

#13

Jesper, Denmark

Last entry on this thread from here......

Jesper, Denmark

>High Octane means LESS willing to ignite. So LOW octane, if any, would be easier to start.

If you prefer to pay a higher price, because it makes you feel that you get better quality, go for it. For gas for the lawnmower etc. it has no real economic impact anyway.

Now I am going back to the shop to turn something with the high cost renewable windmill electrickery we pay extra for here - it makes the lathe run much smoother!

Does not help my skew skills worth a damn, though. Maybe a threadle lathe would help?

Enjoy the rest of your weekend.

Re: Chainsaw Gas

#14

ethanol

Ron in Drums PA

>I've noticed that when I fill my tank up with gas that contains ethanol, I get worse mileage per gallon.

Has anybody else notice this?

Re: Chainsaw Gas

#15

Re: Chainsaw Gas

Barry Turner

>The prime reason some engines require higher octane gasoline is related to their compression ratio's. My Stihl 361 chainsaw has a high compression ratio and requires high octane gas. The blending of ethanol may be a factor in fuel quality, but I don't believe it is the reason some engines require higher octane gasolines. Someone correct me if I'm wrong.

Re: Chainsaw Gas

#16

Re: Chainsaw Gas

Marvin Ewing

>I have always used regular 87 octane gasoline in all of my yard equipment (3 riding mowers, 1 tractor, 3 push mowers, 2 weedeaters) and chainsaws (2 Husqvarnas)and have never had problems with ping or starting. I do add the stabilizer to the gas.

Re: Chainsaw Gas

#17

Keith Tompkins

Re: Chainsaw Gas

Keith Tompkins

>HI Barbara, Here's what happens in any gasoline engine: An air/fuel mixture is compressed then ignited, ideally at just the right time. Problems happen when the mixture ignites prematurely, as the engine's piston is still travelling towards the top of its "stroke". This is called preignition, and in effect, forces the piston downward as it is still is attempting to move upwards. Damage to the piston and rings will result. High engine compression ratios and lean fuel mixtures will aggrivate the condition. HIgh-test gas has a higher octane rating, which means the gas/fuel mixture is less volatile, and will be less apt to ignite until the desired time. The result is more power, and longer engine life.

MOdern auto engines are designed to compensate for this condition...lower compression ratios, computerized ignition and fuel systems which can detect preignition (knock sensors) and change the ignition timing, and exhaust-gas recirculation, which slows the combustion process thereby preventing unwanted preignition, and precise fuel injection metering, which all allow the enging to run on 87 (low) octane ratings.

Your chain saw does not have these systems, and the engines are mandated by federal laws to run in too-lean conditions. Lean mixtures run hot, and are prone to preignition. Added alcohol tends to make the problem worse, as does the 40:1 gas/oil regulations. I run high test in my saws, and only use 3/4 gallon of fuel for each bottle of engine oil. Chain saws do not have an enclosed cooling system, and rely on cooling fins and a built-in fan to cool the engine...the engine must be kept free of debris at all times, otherwise, it can overheat.

Re: Chainsaw Gas

#18

Fog... is there any way that...

Allen Neighbors

>I can identify these stops just by looking at the saw? Are they some sort of plastic gizmo that cover the needle-valve tops? Or am I way off base?

Re: Chainsaw Gas

#19

Re: Chainsaw Gas

Barbara Gill, Remlik VA

>Thanks Keith.

Re: Chainsaw Gas

#20

Re: Chainsaw Gas

Bill Neddow

>Running lean apparently contributed to the problem, my Stihl dealer said. He set it back to factory specs. Guess I will have to knock of the limiter and adjust the saw myself.

Re: Chainsaw Gas

#21

Re: ethanol and reduced milage

Dave Anderson (PacNW)

>You are right that gasoline with 10% Ethanol will get less MPG than straight gas. The reason is that Ethanol only has 80% of te BTU's of gasoline. This means 20 mpg on straight gas = 16 mpg on sraight ethanol. So a 10% blend will get .8% less MPG or 20 mpg on gas = 18.4 mpg on a 10% blend

Just my 2 cents worth

Dave Anderson (PacNW)

P.S. The most fearsome words ever spoken are; Hi! I'm from the Gov'ment and I'm here to HEP you!!

Re: Chainsaw Gas

#22

Bill, what does the limiter look like?

Allen Neighbors

>

Re: Chainsaw Gas

#23

Dick Hines

Re: Chainsaw Gas

Dick Hines

>I have a F150 with the big V8 and it runs just fine on regular gas. I also have a biv V twin motorcycle with 9.1 to 1 compression. I would never think of running anything but high test. S&S says use alky laced gas only if you can get nothing else. And then only put enough in your tank to get to the next alky free station.

Re: Chainsaw Gas

#24

Re: Bill, what does the limiter look like?

Bill Neddow

>I have no idea Allen. But I intend to do some exploring as I do not want the engine to seize up again. The dealer will only set it to "factory specifications", which, as everyone has pointed out, is far too lean. Maybe someone else has done the modification.

Re: Chainsaw Gas

#25

Keith Tompkins

Re: Chainsaw Gas

Keith Tompkins

>I spoke with my Stihl dealer today when I stopped by to buy chain saw oil. According to him, all Stihl saws require "medium" grade or better fuel. Although the carbs are still adjustable, the range of adjustment is still below the optimum operating ratio....too lean.

BTW, my saw is a Stihl 028 super, which I bought 19 years ago. I only run Stihl oil, and have cut approx. 100 cords of wood with this saw, plus all my turning blanks with no repairs.

Remember, when your saw begins to run out of gas, it is running out of oil as well. At the first sign of running out of gas, shut off the saw and refill!