Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Husky Pro air compressor ???

Posts

Husky Pro air compressor ???

#1

Husky Pro air compressor ???

Ed Moore in SW Virginia

>My air compressor may have died today and I am considering the 60 gallon Husky Pro which is 3 HP for $400 at Home Depot. There is an Ingersoll Rand with similar specs for $600.

I would be interested if you have experience with either of these compressors and your opinions of them.

Thanks for your help.

Ed

Re: Husky Pro air compressor ???

#2

Re: Husky Pro air compressor ???

Vince

>Ed,

I have have a HP 60 gallon Compressor with no issues. Got it 2years ago and use it for ROS sanding and air for blowing of work projects. 220 though FYI.

Vince

Re: Husky Pro air compressor ???

#3

Re: Husky Pro air compressor ???

tm

>I've been using a smaller model Husky for a year and so far no

complaints. I needed an owners manual because the unit I bought

was a demonstrator & didn't have one and the customer service

was excellent.

Re: Husky Pro air compressor ???

#4

the IR is far superior

Jp morgan

>the IR is made better and will last longer.

Re: Husky Pro air compressor ???

#5

Re: the IR is far superior

Ed Moore in SW Virginia

>Thank you, JP. I accept your observation. Actually, the IR is 230 volts, which is probably best anyway. I assume that Northern Tool would have it in stock and there is an NT store not far away.

I wonder just how loud it is. I would like to put it in a little room off the shop - if I had a little room. [grin]

Ed

Re: Husky Pro air compressor ???

#6

Little Question - IR!

Mark Mandell - Gone Round In Jersey

>The IR is a much better compressor. I bought my SS3L3 from NT, and it was drop shipped from IR. I also bought the maintenence kit which is IR's synthetic oil and several filters. Using the synthetic oil [U] DOUBLES[/U] the warranty. This served me very well because my pump went "loud" at about 14 month. IR sent a tech to my house, changed out the pump and also reset the regulator to a higher range (110 to 145), All at no charge!

I would note here, Ed, that you should be careful when comparing units by price. NT's catalogue list the IR SS3J3 (12 cfm) at $849. They have an IR compressor listed for $600, but it's a 24 gal unit rated at only 5.2 cfm.

Now, if you want a truly fine compressor, NT also sells Quincy, and for $1,250 you can have a 2-stage 16cfm 175 unit delivered to your garage. Were I shopping now, there's no question that one would be hooked up in my system.

mm

Re: Husky Pro air compressor ???

#7

Thanks, Mark. Good info!

Ed Moore in SW Virginia

>I just called the NT store nearby and they have the SS3L3 for $600. I am probably going to get the SS3L3. Your comments about the warranty have been taken on board and I will probably go that route, too.

In order to bring it home I must lay the compressor down because I have a cap on my pickup. I was told that it must have 24 hours vertical before it is turned on due to the oil.

Ed

Re: Husky Pro air compressor ???

#8

Re: Husky Pro air compressor ???

Barry Turner

>I have had the Husky Pro with 60 gallon tank for about two years now. I believe my particular unit rates the HP at something like 6.5 HP, which is probably quite inflated. Three (3) HP is probably more realistic. I have had excellent service from it, although I don't use it heavily. I use it mostly with a blow gun for clearing wood shavings, but I think it has the capacity to handle most any spray gun, air sander or other tool that I would choose to use. It's not quiet, but it usually cycles on only once or twice during a 4 or 5-hour turning session.

Re: Husky Pro air compressor ???

#9

Re: Two More Tips *LINK*

Mark Mandell - Gone Round In Jersey

>1. Go to McMaster-Carr.com and order an automatic tank drain, part No. 4919K13 for $49. You'll also need some 3/8" brass pipe and fittings (2 street els, a 3/8" ball valve, nipple or two) to remove and replace the tank petcock drain and bring it out clear of the tank when upright. My tank stays quite dry and the same drain valve has been bullet-proof for 4 years. The ball valve goes in before the auto drain so you have a full closure if you have to pull the auto valve to clean etc.

2. I couldn't get the belt/pulley shroud to stop making a rattling noise so I removed it. If you place the unit some place where things or people can't get something in that fan/pulley, take the shroud off. Quieter and I think it cools the pump better anyway.

3. After you set it up, run it for 6 or 8 cycles and then drain and replace the oil with the synthetic. This gets any stray dust or filings out of the pump. Then change the oil again after 4 months. After that once every 6 months to a year depending on use. Keep a record of the dates of the changes.


McMaster

Re: Husky Pro air compressor ???

#10

Thanks for your help. There's an ...

Ed Moore in SW Virginia

>Ingersoll Rand 3 HP, 60 gallon SS3L3 sitting in my shop. And the real good news is that my younger son came home at exactly the right time to help me maneuver it into the shop.

OTOH, SWMBO came out to the shop, saw the size of the new compressor relative to the old double tank nailer and made the obvious unnecessary remarks. I have been painting her kitchen cabinets, so the noise will abate in due time. The Graham ceramic paint looks super and she wants me to continue painting. Years ago she made remarks about a vanity I made and it sat unfinished for 4 or 5 years. I'm sure that she doesn't want a 4 or 5 year delay before I finish the kitchen. [grin]

Ed

Re: Husky Pro air compressor ???

#11

Re: the IR is far superior

Jp morgan

>yes -- it is loud so putting it off somewhere is a desirable solution.

also, go for the largest you can afford -- it will be less expensive to run in you'll not be cycling as often