Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

holes for Niles SS stoppers

Posts

holes for Niles SS stoppers

#1

holes for Niles SS stoppers

Ed Karch

>I was out yesterday looking for the perfect reamer to size wood for Ruth's stoppers. couldn't find one. Talked with Scott Hurley who has the same problem. We thought about router bits and other expensive solutions. Came up with turning a bit the same size as the stopper and covering with sand paper to ream out an undersized hole. All this thinking wore me out so I went home and took a nap. Woke up and went out to my collection of old bits and selected a 3/4" spade bit from the rusty pile. Ground off the sides to a proper Niles taper and chucked it in the drill press. Worked perfectly. A rack of stoppers will go off to the winery today.

Re: holes for Niles SS stoppers

#2

grinding spade bits (and why ream?)

John K Jordan

>>...a 3/4" spade bit from the rusty pile

Reminds me of an article I read from the '70s. The author reground spade bits to make wooden wheels for toys. Also, Rude Osolnik described once that he ground spade bits to drill the hole and shape the opening of his weed pots in one quick operation.

But I don't understand why you need to ream the hole for the bottle stoppers. I simply drilled a hole (3/8"?) and used epoxy. I did put a couple of scars on the shaft with a file to give the glue a bit more to hold but I'm not even sure this is necessary. Does this method have disadvantages I haven't considered? Or are you using the threaded versions and need to fine tune the hole for easy threading?

JKJ

Re: holes for Niles SS stoppers

#3

Steven Antonucci

Aren't they a standard Tap size?

steve antonucci

>I turned a stopper (not sure if it was a Niles or not) a few weeks back, and was pleasantly surprise to find the threading was a standard size to a tap that I already owned. 10 seconds after drilling a "close enough" sized hole, I threaded it with a standard tap and was done...

Steven

Re: holes for Niles SS stoppers

#4

Re: Aren't they a standard Tap size?

Bruce Lane

>I think it was in reference to the creation of a hole in a stand as opposed to the stopper top.

Bruce

Re: holes for Niles SS stoppers

#5

Re: holes for Niles SS stoppers

Ken George

>I used a Unibit (a stepped drill) don't remember what size but it worked great.If you don't mind looking at a stepped hole.

Re: holes for Niles SS stoppers

#6

Re: holes for Niles SS stoppers

john lucas

>Excellent idea. I have 2 step drills I'll try them and see. When I built my stopper display I simply drilled 2 holes. I don't remember the sizes but I adjusted the size and depth until the stoppers sit the way I wanted them to.

Re: holes for Niles SS stoppers

#7

Re: grinding spade bits (and why ream?)

Ed Karch

>The hole is for a display stand after the stoppers are finished.

Re: holes for Niles SS stoppers

#8

Re: grinding spade bits (and why ream?)

Ed Karch

>I considered unabits but they are a bit expensive compared to an old spade bit.

Re: holes for Niles SS stoppers

#9

yes, that makes more sense

John K Jordan

>

Re: holes for Niles SS stoppers

#10

Re: grinding spade bits (and why ream?)

john lucas

>you can buy half way decent unibits from Harbour Frieght or Northern Tools really cheap. Watch for thier sales. I think I paid $3 each for mine.

Re: holes for Niles SS stoppers

#11

Re: holes for Niles SS stoppers

Scott Hurley in N. VA

>Ed,

We also discussed taking a piece of wood, turning it to approximately the size of the stopper, gluing sandpaper to it and using that as a reamer. I tried it, and while it worked, it loaded up the sandpaper almost immediately, then started burning the hole (test piece of pine). I got it to work in the cherry stand, but it took a lot of patience and several pieces of 60-grit to do 10 holes. I like the idea of a ground down spade bit much better.

Scott

Re: holes for Niles SS stoppers

#12

Why taper the holes?

Ruth Niles

>If you just drill a 3/4" hole, the top o-ring will sit on that perfect, no need to try to taper to fit the taper of the ss base.

Re: holes for Niles SS stoppers

#13

Re: Why taper the holes?

Ed Karch

>Ruth

The rack I built is in an arc shape so some of the stoppers are nearly sideways. This is a rack for a commercial winery so there will be a lot of handling unlike a collection rack. I figured the taper might work better.