Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Looking for finishing "jig"

Posts

Looking for finishing "jig"

#1

Looking for finishing "jig"

Larry In Lima

>I'm looking for something like a lathe with the 1x8 spindle, that would just be used for finishing things once they are turned. Something like a headstock with a spindle, but no bed, no motor, no power, etc. I'd like to be able to just manually turn/rotate whatever finished item I have, and leave it to dry. Ideally, it would accept a chuck, etc., for holding the wood while it is being finished. Some of the finishes I use take a while to dry, and I'd like to use the lathe during this time. I find myself rushing things so to speak in order to get them off the lathe so that I can go on to something else.

Of course I'm too cheap and poor to want to dedicate an actual lathe to the finishing process.

I had seen someone making these on Ebay a couple years ago, but anyway, does anyone know where to find one of these types of things?

Larry

Re: Looking for finishing "jig"

#2

Re: Looking for finishing "jig"

Steven Kubien

>Larry,

I've never seen a commerical unit like you describe unless it was a lathe headstock, salvaged from a dead lathe. If it was me, I would get a steel shaft machined to whatever spindle size you need (I think you said 1x8) and support it in some pillow block bearings, mounted on a bench, board, sawhorse, anything.

Just my thoughts.

Steve Kubien

Re: Looking for finishing "jig"

#3

Re: Looking for finishing "jig"

elliott

>check craigslist. i've seen ads for inexpensive lathe

Re: Looking for finishing "jig"

#4

Re: Looking for finishing "jig"

Raymond Overman in SC

>If it's 1" x 8tpi why not get a threaded dowel and make something out of old two by fours. You can buy a 1" x 8tpi thread box (if you don't have Roy Underhill around to make you one) from Grizzly like I did and thread one end of a 36" dowel. Use a couple of 8' two by fours to build your frame and drill a 1" hole in the uprights to accept the dowel. You could even turn a hand wheel to make the rotation go easier.

Re: Looking for finishing "jig"

#5

Re: Looking for finishing "jig"

bowlman

>You might also check out the carving head designed by Trent Bosch (available from Craft Supplies USA) ... $144.50 depending on spindle size prices and part numbers are:

368-4400 1" x 8tpi

368-4222 1.25" x 8 tpi

368-4300 M33-3.5

and another version in the new Packard catalog Woodcut Pro-Mount Detailing Stand, page 65 ... $109.95 part # 301700; you will also need paret number 301703 and maybe 301704(table clamp) ... and of ciurse 45840

indle adapter of your choice for an extra 29.95

I have the Trent Bosch model and I like it so far.

Re: Looking for finishing "jig"

#6

Make One

Ron in Drums PA

>1x8 bolts are available

Re: Looking for finishing "jig"

#7

Re: Looking for finishing "jig"

Lynn Edwards

>One of our club members made a device powered with the motor from a rotissery. It turns very slowly and he has quite a number of devices made to hold items he is finishing

Re: Looking for finishing "jig"

#8

Re: Looking for finishing "jig"

john lucas

>Larry Ed Lewis in Chattanooga, Tennessee has built exactly what you want. he uses it to finish his bowls with epoxy. It rotates at 8 rpm. and has 3 or 4 spindles.

I thought about jury rigging it with a barbecue Rotisserie motor. It runs slow and wouldn't be hard to rig up a 1"x8 thread to it. Supporting the bowl would be the only problem.

Re: Looking for finishing "jig"

#9

Make one. Here's how.

Allen Neighbors

>Ron mentioned that 1x8tpi bolts are available. You can buy one that is 10 or 12 inches long for your spindle shaft. Buy two 1" pillow-block bearings, and mount them where you want them, about 6 or 8 inches apart (dependent upon the length of your bolt). Make a hand wheel out of 1/2" plywood with a crank handle for rotating the spindle. Put the spindle/bolt through the plywood handwheel,and glue it on next to the bolt head. Then mount the bolt through the pillow block bearings. Mount a 1x8 nut on the threaded end of the bolt. Screw on your chuck. Tighten the nut up to the back of your chuck and superglue the nut in place. (don't stick the chuck). :) Bob's your uncle. Done.

Re: Looking for finishing "jig"

#10

Re: Looking for finishing "jig"

Larry In Lima

>Thanks guys, I think one of the ready made stands is the easy answer for me. Appreciate the part numbers too. Larry

Re: Looking for finishing "jig"

#11

Re: Looking for finishing "jig"

Randy G

>Check the classifieds, the guy with all the lathe stuff has a Trent Bosch stand.

Re: Looking for finishing "jig"

#12

Re: Looking for finishing "jig" *LINK*

Ron McKinley

>Is this what you're looking for? It's only $18.95......Ron


Craft Decorating Lathe

Re: Looking for finishing "jig"

#13

JL

Re: Looking for finishing "jig"

JL

>Take a tip from the carvers and check out what they use. They have or make small carving "vises" so they can rotate their pieces.

Re: Looking for finishing "jig"

#14

Re: Looking for finishing "jig"

Russ Fairfield

>Maybe you should rethink how you will be using this "wood spinner" and your not wanting it to be powered. I am wondering what benefit there is in using it if it isn't powered. You lathe will be sitting idle while you are using the wood spinner for finishing. Unless there is someone else doing the finishing, why not just use the lathe you have??

There is a definite benefit if your wood spinner is powered. That way you can apply a heavy coat of finish and leave it to spin to prevent runs and insure uniform drying while you are at the lathe turning the next one. A BBQ drive motor and a couple small pulleys will be enough RPMs for most finishing tasks.