Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

tenon turning..I forgot how !!

Posts

tenon turning..I forgot how !!

#1

tenon turning..I forgot how !!

Paige Cullen

>Hi,I once took a woodturning class to try to learn bowl turning.I've been turning pens,stoppers,light pull and other small items for a few years.I have the bowl mounted with a faceplate and the tail stock pulled up.I've been shaping the side with several bowl gouges.I'm attempting to turn the tenon but can't exactly remember what to do to get the side of the tenon to be nice and straight.Right now the end is pretty flat but the side looks like a mountain.Everyone can remember when they got started turning bowls will know how stupid I feel right now.

Can some one give a beginner some advice and maybe point me in the direction of a video instruction.I seem to do better when I can see something.I've looked at many websites and can't find any thing.The tenons are already turned in the videos.

Actually,I should wait until Tues. when I have a Woodturners' meeting of our club.

Anyway...anyone got any advice?

Thanks in advance,

Paige

Re: tenon turning..I forgot how !!

#2

Re: tenon turning..I forgot how !!

Carol - now in NC Nebraska

>Uhhh... just a rookie myself, but if you have the piece on a faceplate why do need to turn a tenon?

A tenon fits into a chuck to hold the piece. At least, that's my understanding.

A faceplate is already holding the workpiece.

Did I miss something?

As for helpful videos. I got the Jimmie Clews set of three. It was recommended as having great camera angles so a rookie could see exactly what was needed to understand why Jimmie is teaching. I would agree with that. That other neat thing is that he progresses into some vary advanced things. Don't let that throw you. The rally basic stuff with good explanation is also there. To me that means the video will be useful for some time.

And since you belong to a turning club, you have the best learning resource. Surely someone there can be your personal mentor. Just ask. They will probably stand in line to help you!!

Re: tenon turning..I forgot how !!

#3

Re: tenon turning..I forgot how !!

Mark Paulley

>Paige,

The tenion should fit into your 4 jaw chuck and not bottom out. I measure and mark down what are the max and min diameters the chuck will close and open to for references. Be sure the tenion is at a 90 degree right angle so you get a good tight clamp and so the top of the jaws hit the bottom of the bowl. This gives 2 very important pressure points. I know its not very informative but I do not know how to verbalize what you need very well! Hope this helps some!

Sorry!

Mark

Re: tenon turning..I forgot how !!

#4

Re: tenon turning..I forgot how !!

Jorge Castaneda~Downeast Maine

>Paige,

I imaging you mounted the faceplate in what you want to be the inside of the bowl, Shape the outside and to make the tenon, just go at it with your bowl gouge, the bevel paralell to the ways, first determine the diameter you need, this is dictated by the jaws in your chuck, it must be somewhere between the min and max openings of the jaws, if your chuck is a Oneway, make a straight tenon, if it is a Vicmarc or Nova, make the tenon slightly like a dovetail, with the bigger diameter outside.The face of the jaws must seat in a flat around the tenon, and the tenon cannot bottom out or your piece will dismount in a hurry.

Clear as mud uh?

It is a lot easier to do than to explain.

Good luck

Jorge

Re: tenon turning..I forgot how !!

#5

Denis Putland

Re: tenon turning..I forgot how !!

Denis Putland

>I use my gouges for shaping my tenons but if you are having trouble geting nice staight edges,try using your parting tool to square it all up.

If you have a oneway chuck then you do not have to be very fussy as they hold on to your tenon like tiger::)))

Denis

Re: tenon turning..I forgot how !!

#6

Re: tenon turning..I forgot how !!

Paige Cullen

>Carol,It's so that I can reverse chuck the piece in a chuck when I go to turn the inside of the bowl,but thanks for being there for a fellow newbie !

Paige

Re: tenon turning..I forgot how !!

#7

Re: tenon turning..I forgot how !!

Paige Cullen

>Denis,I have a Barracuda 3 chuck

Re: tenon turning..I forgot how !!

#8

Re: tenon turning..I forgot how !!

Paige Cullen

>Thank you Mark!

Re: tenon turning..I forgot how !!

#9

Re: tenon turning..I forgot how !!

Paige Cullen

>Thanks Jorge,

I'm not real sure what tool to use and what angle to approach from to make the side of the tenon 90 degrees.

Re: tenon turning..I forgot how !!

#10

Here go, Paige

Allen Neighbors

>Leave the face plate mounted piece on your lathe. Slide the tailstock back out of the way. Mark the width of the tenon on the base of the piece. Move your toolrest up to the bottom of the piece, perpendicular to the ways (across the ways). Holding your parting tool in alignment with the ways, push it straight into the piece to the depth of the tenon. Move the parting tool to the left, one width, and do it again. Now it should be easy to use a detail gouge or Oland tool or Bedan, or just about anything to clean it up, leaving a nice square sided tenon.

Hope this helps.

Re: tenon turning..I forgot how !!

#11

Here's a good DVD *LINK*

Ron in Drums PA

>Click on Video


Turned Bowls Made Easy

Re: tenon turning..I forgot how !!

#12

Re: tenon turning..I forgot how !!

Jorge Castaneda~Downeast Maine

>Paige,

to make the cylinder the bevel is parallel to the ways, to make the flat, the bevel is perpendicular.

When I make the tenons I like to be right on top of it looking down.

Jorge

Re: tenon turning..I forgot how !!

#13

Re: tenon turning..I forgot how !!

Carole Valentine

>Paige, probably the easiest way is to take off the bulk of the wood in the tenon area with your gouge and then use your parting tool to clean it up and flatten the shoulder. I just use my gouge and sometimes a skew, but you may or may not be comfortable with that. I highly recommend Bill Grumbine's bowl video (sorry Bill, I can't remember the title and am too lazy to go look!) for anyone just starting to turn bowls. You might also do a search on YouTube...as I recall there were several videos on turning bowls.

Re: tenon turning..I forgot how !!

#14

Jesper, Denmark

Re: tenon turning..I forgot how !!

Jesper, Denmark

>You can easily turn the tenon nice and cylindrical with either a square scraper or a parting tool. Put the tool rest square to the centerline and a little lower than the center. A few light cuts will leave you a clean tenon and a square land at the bottom of the bowl.

You only need a 1/8th or 3/16ths long tenon to get a good grip and it should not bottom out in the chuck.