Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Looking for a faceplate thread adapter

Posts

Looking for a faceplate thread adapter

#1

Looking for a faceplate thread adapter

Ilya Zavorin

>I have a faceplate that I want to use on different lathes, so I am looking for a male-female thread adapter. Are there vendors that sell them? The faceplate is 1" X 8 TPI, the lathes are M3 (Oneway) and 1 1/4 X 8 TPI. Thanks

Re: Looking for a faceplate thread adapter

#2

oneway sells spindle adapters

mm

>

Re: Looking for a faceplate thread adapter

#3

Re: Looking for a faceplate thread adapter *LINK*

ET

>Thread adapters are available from Craft Supplies and Best Woods (uummmm, I think). The price from both places is $60 each. Oneway have adaptors on their web site, but they are made only for their lathes, ie with the female metric M33 x 3.5 to whatever your accessory (faceplate).

Scroll down page to find adapters: http://www.oneway.ca/lathes/1640_access.htm

You will find it is cheaper to sell the faceplate and buy new ones to fit your machines. ET


http://www.oneway.ca/lathes/1640_access.htm

Re: Looking for a faceplate thread adapter

#4

Check Penn State

Steven Kubien

>

Re: Looking for a faceplate thread adapter

#5

Craft Supplies and Packard Woodworks ... *LINK*

Brian Hahn in SW Wisconsin

>Both carry this-to-that spindle adapters.

Here's a link to Craft Supplies:


Craft Supplies Spindle Adapters

Re: Looking for a faceplate thread adapter

#6

Re: Craft Supplies and Packard Woodworks ... *LINK*

E.T.

>Here is the link to Bestwoodtools. While you are at their site, check out the faceplates. Many are cheaper than an adapter. As are ths faceplates at any of the other tool dealers. ET


http://bestwoodtools.stores.yahoo.net/exturprod.html

Re: Looking for a faceplate thread adapter

#7

Re: Looking for a faceplate thread adapter

Gordon Seto

>If you have only one or two faceplates to convert. It may be better to sell those and buy new. A poorly made adapter would introduce alignment problem. I like to use faceplate rings; they just hold on to your chuck jaws. You don't have to worry about spindle thread size and allow you to flip your blank back and forth without losing its center.

Gordon

Re: Looking for a faceplate thread adapter

#8

Re: Looking for a faceplate thread adapter

robert bilevich

>I have one to sell $25.00 plus shipping,never used,mistake when bought.call 562-865-8256 in Ca.

Re: Looking for a faceplate thread adapter

#9

Re: Looking for a faceplate thread adapter

Ilya Zavorin

>My problem is that I work on several lathes: one at home which has a 1" thread and two at a local woodworking club with 1.25" and M3. I have a large blank that will take several sessions to finish so, and I clearly do not want to take it off one f/p and put it on another. The f/p ring seems to be exactly what I need. Thank you very much for your suggestion!

Re: Looking for a faceplate thread adapter

#10

Re: Looking for a faceplate thread adapter *LINK*

Gordon Seto

>Faceplate ring may be exactly what you want. You can switch to different lathe no matter what spindle size. The ring is attached to the dovetail jaws of the chuck on your lathe.

Gordon


Face plate ring

Re: Looking for a faceplate thread adapter

#11

so in regards to penn state's

Randy G

>So I've gone back and forth with the question originally asked above and the answer's that are being given. I have a Jet Mini and a Powermatic 3520, there's been a few times I'd like to use the small chucks or accessories I have on the Mini on the Powermatic. The question I have with the places selling these is Penn State and Amazon sell them for about 20-25, and Craft supplies and others are like 60? Knowing that you get what you pay for, is it really twice that much? Yes I know I'd rather be safe than sorry but would love to understand why it's worth that much more?

Re: Looking for a faceplate thread adapter

#12

I've got a Penn State

Steven Kubien

>I've got a PSI adapter that goes from 1-1/4" 8tpi to 1"x8tpi and I have had no issues with it. Mostly I use it for my doughnut chuck which has the faceplate from my mini lathe mounted on it. I runs true enough for me (but I've never measured the runout).

HTH

Steve Kubien