Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Removing Glaser Gouge From Handle?

Posts

Removing Glaser Gouge From Handle?

#1

Removing Glaser Gouge From Handle?

David Propst

>I have a couple of Glaser tools that I have never used much. I have V15 5/8 bowl gouge that because of the narrow V grind clogs on me too frequently and the steep V-flute does not allow me to use a Ellsworth type grind which I prefer. I'm going to replace it with a Thompson V gouge, which is more like my other 5/8th, a very short Crown PM gouge. The other is tool I have is a Glaser bowl skew which I create a disaster with every time I pick it up :-)

My question is how do I remove the Glaser gouge from the handle? I remember reading at one time to use heat (torch or a gas grill?). I know they are replaceable, but before I do my usual try it and ask later I thought I'd ask.

David

Spending some time in the shop!

Re: Removing Glaser Gouge From Handle?

#2

Re: Removing Glaser Gouge From Handle?

Jennifer@Indy.USA

>I don't have an answer for your question David....but I do have a comment on your post.

yippee Ki aye!!!! That you're getting some shop time :)

I'm smiling just knowing you're out there turning. I know it's been a while.

Jen

Re: Removing Glaser Gouge From Handle?

#3

Re: Removing Glaser Gouge From Handle?

Wally Dickerman in Arizona

>Hi David,

I also am glad to see that you are getting some shop time.

I'm quite sure that Glaser installed the handle using expoxy, which takes some heat for removal. I have 2 Glasers but I've never removed the handle.

Clogging the glaser V flute? Well I seem to remember that you are a very aggressive turner, which accounts for that.

I recently acquired a Thompson 5/8 inch gouge and I really like it. It comes off the wheel sharper than my other gouges, and it stays sharp longer. Sounds like you are planning to install the Thompson in your Glaser handle. A suggestion...I prefer the feel of wood in a handle. When I made a handle for my Thompson I bored a hole in the butt end and put in some lead shot followed by a plug. It added just enough weight to feel just right. I experimented with the amount of shot for the right balance by changing the amount of shot until I was satisfied. Then I glued in the plug.

You'll enjoy the new gouge,

Wally

Re: Removing Glaser Gouge From Handle?

#4

Lead Shot.....

Wally Dickerman in Arizona

>David, if you decide to use my suggestion on a wood handle and lead shot, and you can't find any lead shot, I can help.

I used to do a lot of skeet shooting and reloaded my shotshells. I still have a supply of #9 lead shot, and could send you a little. Doesn't take very much.

Wally

Re: Removing Glaser Gouge From Handle?

#5

Re: Removing Glaser Gouge From Handle?

Doug Thompson near Cleveland

>To replace the blade in a Glaser handle first hold the handle in a wood vise with the tool end pointing up (remember the handle is filled with shot). Heat the first two inches with a propane torch until the epoxy softens, this will take about 4-5 minutes. Use vise grips to hold onto the blade (remember it's hot as a firecracker) when it starts to twist in the handle keep heating until it slides out with no effort. DO NOT use extra force to remove it... DAMHIK but I almost lost my eye! If the tool has a silver bushing this must stay in and only the blade is removed. Now let it cool down. Clean the old epoxy and use a good quality epoxy to install the new blade.

Jerry made the bushing to fit the steel so the replacement steel has to be .015 oversize. I have steel to fit but you must contact me before you place an order to make sure I have them in stock.

Re: Removing Glaser Gouge From Handle?

#6

Re: Removing Glaser Gouge From Handle?

Halsey

>I found a heat gun and about 5 min and it came right out.Be careful it is hot. Halsey

Re: Removing Glaser Gouge From Handle?

#7

Re: Removing Glaser Gouge From Handle?

Molly Winton

>Wallllllly, don't get started on the agressive turner topic (waggling finger at you)!

David, I'll add my yippeee yahoooo to your shop time too! I proudly own and display a Probst piece in my livingroom.

Re: Removing Glaser Gouge From Handle?

#8

Re: Removing Glaser Gouge From Handle?

Wally Dickerman in Arizona

>Hmmmm...I don't own a Propst piece. Come to think of it, I don't a Molly piece either. I recently received a Jennifer piece though.

Wally

Re: Removing Glaser Gouge From Handle?

#9

Re: Removing Glaser Gouge From Handle?

Jennifer@Indy.USA

>.....and that makes my heart feel good :)

Re: Removing Glaser Gouge From Handle?

#10

Re: Lead Shot.....

Jennifer@Indy.USA

>Would BB's work just the same? It would probably take more though?

Re: Removing Glaser Gouge From Handle?

#11

Re: Lead Shot.....

Wally Dickerman in Arizona

>Sure, BB's will work, and yes it would take more of them. They're made of steel instead of lead these days. You can leave them loose or you can squirt some CA on them before installing the plug.

Wally

Re: Removing Glaser Gouge From Handle?

#12

Me Too......

Wally Dickerman in Arizona

>

Re: Removing Glaser Gouge From Handle?

#13

Re: Removing Glaser Gouge From Handle?

Molly Winton

>We're just going to have to resolve that. Lucky you for having a Jennifer piece. I've got one too. They're delightful. Hmmm, I don't have a Wally piece either.

Re: Removing Glaser Gouge From Handle?

#14

Re: Removing Glaser Gouge From Handle?

Jennifer@Indy.USA

>Oh, Molly Wally's pieces are wonderful! So thin and light and they feel like they are going to float right out of your hands. Just scrumptious. At least the one I have here in my living room is.

Hee-hee :)

Re: Removing Glaser Gouge From Handle?

#15

Incomplete Collection

David Propst

>Wally, I'll have to rectify that glaring omission in your collection!

Guess I better start spending some more time in the shop. My skills have become a bit rough. I have not finished a piece in about a year until last week. When I showed it to my wife she hefted it, frowned, and said "are you going to take more out of the bottom, it's really heavy". (I actually greatly appreciate her criticism.) However it was done, gave it to a coworker who showed it off for days.

Before Molly gets riled up over aggressive turners, I'll say I do love to make the curls fly when roughing. But when it comes to shaping a piece I take micro shearing cuts, stop, look, take off a few more microns, stop, look... I have that aggressive turner thread saved as a pdf.

I could never sharpen the Glaser without a little dip right before the tip (Wolverine or Tormek) and the steep V really does clog with wet wood (Jennifer Shirley agrees with me so it must be true, she's darn near famous!).

Removed the gouge just like Doug described without injury and probably have sold it too. I am going to tap the handle and put in set screws. Bought a rubber plug to tap in to keep the shot in.

Best Regards,

David

Re: Removing Glaser Gouge From Handle?

#16

Re: Removing Glaser Gouge From Handle?

Jerry Glaser

>The way I did it when installing a new blade for a used one was to grip the blade in a vice with the handle down. The blade is the plug that keeps the lead shot from coming out of the handle on one end. Then using a propane torch I would heat the top three inches of the handle holding onto the handle on the bottom end and trying to twist it at the same time. After about a minute of heating the handle can be twisted off and set aside to cool in a vertical position. I used Loctite #680 for securing the blades to the handles and not epoxy. Before you start this removal be certain that the blade you are using as a replacement is the same exact size as the one being replaced. The stock used for the blade is nominaly sized 3/8", 1/2", etc. but the actual size is usually some .010" larger. The lead shot was usually #9 bird shot and was put in with about a quarter of an inch shy of being full. Using #9 shot provides the maximum weight that I felt was needed for reducing vibration. Larger shot such as B-B's would not weigh as much for a given volume. I feel that it's necessary to have some looseness in the lead that's in the handle for vibration absorption. Be sure to clean the blade with a solvent like MEK before using epoxy or other adhesives to join thr blade and handle.

Re: Removing Glaser Gouge From Handle?

#17

About the Glaser Bowl skew

georgetroy

>David I posted an article on using the Glaser Bowl skew here:

http://www.woodcentral.com/articles/glaser_skew.shtml

I'm still using this skew on the side with a burr, it is very effective in cleaning up ridges and chunk outs on segmented turning. I need very little sanding after use.

Re: Removing Glaser Gouge From Handle?

#18

Thanks Jerry

Dave Peebles Lyons, Ohio!

>Hello Jerry,

Very kind of you to post on this thread. There is nothing like getting it from the original source.

I hope all is well with you. I would also like to thank you again for all the information you sent to me many years ago when I was beginning on the turning road. It helped me in more ways than you can probably imagine.

Best wishes,

Dave

Re: Removing Glaser Gouge From Handle?

#19

Steven Antonucci

Use Sand or cement (powdered)

steve antonucci

>Cheap, virtually free, and does a good job dampening vibration.

I've got one bar that's 4' long and when I get around to it, I might fill it with sand. It's already 5#, and a little more can't hurt.

Steven