Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

WoodFast lathe tailstock hand wheel

Posts

WoodFast lathe tailstock hand wheel

#1

WoodFast lathe tailstock hand wheel

Mark Paulley

>Hello all,

I have a Woodfast 410 model.

2 questions:

1. The wheel to move the tailstock quill is getting more difficult to rotate, again. Does anyone else have this problem? Know why this happens? There is a set screw in the tail stock that I have yet to fiure what size it is. The people at Craft Supply advised to remove the set screw, blowout the area and replace.

2. I was advised that all WoodFast lathes have a connection for a remote on/off switch, but mine did not, that I can find. Does yours have a remote on/of switch connection?

Thanks for your help!

Mark

Re: WoodFast lathe tailstock hand wheel

#2

Re: WoodFast lathe tailstock hand wheel

mfoster

>I have a Woodfast, but is an older 810. I don't know about your model, or if they have changed over the years, but the advice that Craft supplies gave you seems sound. My tailstock is relatively simple in design, and I would imagine yours is the same. You might have gunk in the machined surfaces that the quill slides in, or in the threads that allow you to crank it in and out. I would use some mineral spirits to clean it all well, then lubricate using either light grease or WD 40. My lathe is one that any number of motor/switch assemblies could be installed. They originally were shipped from Austraia without the motor, and one was added here. Mine has one of the very first variable speed controllers and a DC motor. The electronics were designed and made by a turner in the Seattle area, who has passed away. He provided a remote switch with his, which has an electrical outlet coming out of a box attached to the inside of the lathe stand. I would imagine that yours is nothing like mine though, so this is probably of no help. Good luck

Mike

Re: WoodFast lathe tailstock hand wheel

#3

Re: WoodFast lathe tailstock hand wheel

john lucas

>Mark It's been so long since I worked on a woodfast I don't remember the details. I periodically remove my quill and lube everything inside and out. ON my Powermatic you can just keep extending the quill until it comes out. On the Powermatic the quill gets a little stiff when it gets dirty. This procedure makes it run really smooth for a few months or more.

Woodfast lathes probably have metric screws.

Re: WoodFast lathe tailstock hand wheel

#4

Re: WoodFast lathe tailstock hand wheel

Molly Winton

>Hi Mark, I feel your pain! I have a Woodfast M-410 short bed. You describe EXACTLY the same problem I have with my tail stock. The set screw is 3mm. I've removed my set screw, blown it out, disassembled the entire tail stock, cleaned it, lubed it, etc. etc. It will work fine for a short time, then back to it's old screech, bind, and catch routine. It gets to the point where I have to use two hands to rotate the wheel. I've never found a satisfactory solution, which is very frustrating. One person's advice was to take it to a machine shop and see whether the threading inside the unit is machined properly. I've not yet done that.

With regard to the remote connection, I don't know if mine has one of those or not either. I've never found one, or even heard this was a possibility.

Not much help, am I. Sorry, I guess I'm just a 'misery loves company' post. Let me know if you find out anything useful.

Re: WoodFast lathe tailstock hand wheel

#5

Re: WoodFast lathe tailstock hand wheel

Mark Paulley

>Hello all,

Thanks for the help. It was ALL useful. I have the short bed too with the variable speed.

Does the quill come apart after removal of the 3mm set screw?

Molly,

Have any problems with the on/off switches? I have replaced mine once so far and will replace again here in the next few days. Each switch is only $11 so its not too bad. They just stop working consistently! Go figure!

Marvin Ewing here in Louisville showed me the connection on his WoodFast which was just hanging under the lathe frame.

Again thanks to all for your help!

Mark in snowy but melting KY

Re: WoodFast lathe tailstock hand wheel

#6

Re: WoodFast lathe tailstock hand wheel

E.T.

>I had this tightening prblem with another tailstock spindle. I found that when the spindle was moved in and ut the spindle would rotate the set screw until it touched the bottom of the groove in the spindle. And so the set screw tightened until the spindle would not move. I put a drop of some light gripping loc-tite on the thread to stop the set screw from moving. That lathe manufacturer now uses a longer set screw that sticks out of the tail stock casting and puts a hex nut on it that is tightened against the casting, thus locking the set screw.

I, also, have the Woodfast 410 lathe and have never had a problem with the tail stock spindle. ET

Re: WoodFast lathe tailstock hand wheel

#7

Re: WoodFast lathe tailstock hand wheel

John Kyler

>My Woodfast got real bad...

I used PG2000 and sprayed it real good and worked it back and forth until it freed up.

The grease got real dry all of a sudden.

I now have a PM4224, and spared it when new.

John

Re: WoodFast lathe tailstock hand wheel

#8

Re: WoodFast lathe tailstock hand wheel

Molly Winton

>The quill does come apart after removing the set screw, but I also have to remove the steel 1/2 round thingy on the top of the tail stock.

My switch is bad too. Apparently dust can get into the switch, which interferes with the connection. If you bang on the stop button that usually knocks the dust free, and it will start again. I got the replaceable switch that is supposedly sealed, so when I change it out I shouldn't have the problem anymore, but I've not replaced it yet. I don't use my Woodfast very often anymore, because I do most of my hollowing on my Oneway 1224.