Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

***Ted needs help by 5pm today (ET)***

Posts

***Ted needs help by 5pm today (ET)***

#1

Ellis Walentine

***Ted needs help by 5pm today (ET)***

Ellis Walentine

>Ted is away from his computer and asked me to please move this message here from the hand tools board, where he inadvertently posted it earlier today. Here's the message. Thanks.

Ellis

Quick help needed...

Ted Owen, Pittsburgh -- Friday, 7 March 2008, at 9:53 a.m.

Our turning club has decided to run a series of newsletter articles on four important power tools for the turning shop--lathe, grinder, bandsaw, chainsaw. Since I'm a bandsaw nut, I've been asked to write the full-page article, or series of articles if I prefer, on the bandsaw as it relates to turning. And I have to turn it in to the newsletter editor by tonight or tomorrow morning.

I've prepared a quick outline as follows:

size--wheels, resaw, table, weight

new vs. used and pricing

features such as tilt table

blades--skip-tooth, 3tpi, bimetal (carbide only if no nails)

guides--not as important in my view as most people believe

support for uneven and unbalanced stock

wedges to keep kerf open on green stock

cutting order--face and bottom flats, true up ends, then curve cuts

Any quick suggestions on what I'm missing, or what should be fleshed out, would be helpful and appreciated. Sorry for the short notice on my request, but it was equally short for me, too.

Thanks,

Ted

Re: ***Ted needs help by 5pm today (ET)***

#2

Re: ***Ted needs help by 5pm today (ET)***

John K Jordan

>Bandsaw as relates to turning. Comments, in no particular order:

The height of the cut is important to me. I use a 14" saw with a riser block for a 12" capacity. Compare in cost and function to a much larger saw without a riser block.

I don't know anyone using carbide blades.

I think properly adjusted guide blocks are very important.

Problems with cutting green, sappy wood vs kiln dry wood. (gummed up blades, gummed up tires, increased friction)

For turning, quality (smoothness) of the cut seldom makes any difference. The fewer teeth the better. Following advice here, I modified a 3-TPI blade by breaking off every other tooth - what an amazing improvement a 1.5-TPI blade has on very thick green wood.

Proper blade tension is king. Low tension results in many problems with thick wood including a bowed cut, increased friction, a bad day. Many stock tension springs are weak and must be replaced.

I've never needed wedges.

Processing a round log section into a turning blank is a common task. The order of cut is important and depends on the goal. I primarily use the bandsaw to prepare turning squares intended for spindle turning. For turning squares I usually cut down the middle of the log by hand, rest one flat on the table and true up one edge, rest that edge against the fence, then proceed to section into squares. I handle bowl blanks differently.

Warn twice about trying to cut across a round section (unsupported). Good way to break a blade or lose a finger.

Don't forget dust collection.

Things involved in tuning the saw.

Horsepower - minimum, optimum?

Adjusting thrust bearings. Keeping hidden thrust bearings clean. Replacing thrust bearings that you didn't keep clean.

Some people resharpen bandsaw blades (I do). There are threads here discussing this.

Importance (IMO) of positioning the bandsaw near the lathe!

JKJ

Re: ***Ted needs help by 5pm today (ET)***

#3

Re: ***Ted needs help by 5pm today (ET)***

adrien

>a little on maintenance? lining up the driving wheels, cleaning the tires, etc.

Re: ***Ted needs help by 5pm today (ET)***

#4

Re: ***Ted needs help by 5pm today (ET)***

bowlman

>You might cosider adding a bigger table to your bandsaw for those bigger, heavier pieces and for the unbalanced pieces like burls. Rockler has one on sale this weekend. The fence even has a run out or drift compensator.

Re: ***Ted needs help by 5pm today (ET)***

#5

Thanks, folks...

Ted Owen, Pittsburgh

>for the helpful comments. I've incorporated them into the piece already.

And thanks, Ellis, for moving the message for me. I know how busy you are and appreciate your help.

Best, Ted

P.S. John, my note was unclear--the actual article states that I believe discussion regarding the brand or style of guides is overblown. I completely agree that their adjustment is very important--keeps the machine happy. Sorry for the confusion.