Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

tool extension from your jig

Posts

tool extension from your jig

#1

tool extension from your jig

john lucas

>I know the Ellsworth jig suggests 2" and Wolverine jig suggest anything from 1 1/2 to 2". What do you all use. I picked 1 3/4 arbitrarily when I got my jig and have occasionally wondered if I should use shorter or longer.

Shorter means the jig will hit the grinder of stone sometimes and longer means you can't use that tool quite as long because you run out of length. Of course in reality when it gets that short it needs to be reground into something else.

Re: tool extension from your jig

#2

Re: I've always used 2"and if ........

Jamie Donaldson

>....you can find a use for stubby bowl gouges I have several to contribute!

Re: tool extension from your jig

#3

Re: I've always used 2"and if ........

georgetroy

>You have stubby gouges to go with your Stubby lathe? You could put a special grind on each and take them to the woodturning club for examples of what to do not to do.

Re: tool extension from your jig

#4

Re: tool extension from your jig

Mike Brazeau

>I currently use 1 3/4". Have a block on my grinder base with 1 3/4 on one side and 2" on the other. We had a weekend guild workshop with Lyle Jamieson, which had a lot of content for one day, but Lyle had a good session on grinding the side grind bowl gouge. He uses 2" setback. Interestingly he removes the handles on gouges that are ground back to almost nothing and uses them for sheer scraping, which is done at vertical 45 degree angle, with the handle end pointing down. At that angle on some pieces the handle gets in the way. It is a very light shearing cut and done only with a freshly sharpened gouge. His gouge grind has a slightly less convex surface on the side grind cutting edge than the Ellsworth grind. After seeing his grind I am going to experiment with 2".

Re: tool extension from your jig

#5

Dick Hines

Re: tool extension from your jig

Dick Hines

>Doug Thompson uses 1 3/4" in his directions for his tools. I use it on my Thompson tools but do hit the jig on the wheel mostily on the right side.

Re: tool extension from your jig

#6

Re: tool extension from your jig

keith zimmerman, Normal, IL

>I have always used 2" for my fingernail ground gouges, regardless of the size of the gouge.

Re: tool extension from your jig

#7

Modify...

Peter Teubel

>John Lucas wrote:

longer means you can't use that tool quite as long because you run out of length.

==================================

When the tool gets too short, just grind the top flat to match the level of the flute. This will allow the tool to 1) enter the jig, and 2) allow for indexing on the (newly) flat part.

Re: tool extension from your jig

#8

Re: Modify...

john lucas

>Peter that's what I just did for my best friend. His favorite gouge was getting too short so I ground it back using my angle grinder with abrasive wheel.

Re: tool extension from your jig

#9

Re: I've always used 2"and if ........

john lucas

>Jamie I've forgotten how Bob Rosand grinds his too short bowl gouges but he has a custom grind for turning beads on his vessels. It left a really clean cut. It seems like he ground each side to half a bead shape so the nose cut the area between the beads.

Re: tool extension from your jig

#10

Re: tool extension from your jig

Bob Ballard

>I talked to David Ellsworth about the 2" he recommends because I have a Wolverine on a 10" grinder.His response was that the important thing was the 60 degree angle on the nose of the gouge not any specific distance.

Re: tool extension from your jig

#11

Steven Antonucci

Ellsworth's distance setting jig is...

steve antonucci

>a block of wood with a hole drilled into it. He epoxies a nickel at the bottom of the hole to keep it from getting chewed up. It was mounted to every grinding bench in the classroom. Simply stick the jig on the tool, put the tool in the hole, and tighten the jig at the bench.

Whether it was 2" or so is anyone's guess...

Steven

Re: tool extension from your jig

#12

Jamieson seminar

Steven Kubien

>Mike, the WGO also just hosted Lyle (or are you in the WGO and I just don't know it?). I got a lot out of the day (and the hands on session on Sunday) and sharpening was certainly part of it. Since then, I have adopted the 2" extension he spoke of but I really can't evaluate it because at the same time, Lyle changed the way I hold my tools and present them to the work, using his 4 cuts. One thing I did like was the little gizmo for going from a bowl gouge (60� or so) to a spindle/detail gouge (45� or so). Now I have no reason to move the base on my Wolverine-ish setup.

Cheers,

Steve Kubien

Ajax, Ontario

Re: tool extension from your jig

#13

Re: Jamieson seminar

john lucas

>Steve can you describe his Gizmo because I was thinking about adding a block to my Wolverine jig so I could sharpen the spindle gouges without moving the Oneway arm. I think I can leave it at the bowl gouge setting and then place a block in the V at the right height so I can sharpen the spindle gouge. I'll have to check it and see.

Re: tool extension from your jig

#14

Re: Jamieson seminar

Ed in Leaside

>Hey Steve, Mike is on the other side of the Big Smoke from you. ;) He belongs to the GHTG.

Re: tool extension from your jig

#15

Kelton sharpenning jig

Jorge Castaneda~Downeast Maine

>John

I use 1 3/4", to me the 2" makes a too aggressive tool, although if all I want is to shear scrape with the sides it is fine; for most of my work, I use the 1 3/4" set up, for the gouges I use to do the inside of bowls I use 1 5/8" extension with a slightly more blunt nose.

I did switch to the Kelton sharpening jig a while back and have no problems at all, also I went to detachable tool handles, the sharpening is so much easier. I like the fact that The Kelton jig can be adjusted vertically too, it is a substantial jig, and I recommend to get the short arm, as I do sharpen without handles, I do not need the long arm.

Take a hard look at it, I think I did a wise investment.

my $0.02

Jorge

Another consideration about detachable handles is that I can switch handle lenghts with the same tool, about a dozen handles serve about 30 tools, that saves a lot of storage space.

Re: tool extension from your jig

#16

the blocks

Steven Kubien

>The sliding arm of the wolverine is V shaped at the end with a plate welded on and the arm of the varigrind sits at the bottom of the V, against that plate (I know you know this but I am thinking as I type and it is scary for me). The blocks of wood sit in the V, against the plate which moves the contact point of the varigrind forward, thereby changing the angle at which the tool contacts the grinder. There are two thicknesses of blocks, one is 3/4" which changes the angle at the business end by about 10�� and another which is around 1" which changes the angle by 15�. He also had imbedded some magnets in the back of each block to keep them from moving around. This all assumes that you've got the bowl gouge sticking out 2" from your varigrind. What is so great about this is that once you have got your wolverine set up for your Ellsworth-style-grind bowl gouge, you do not have to move it for spindle/detail gouges.

Now all of the math wizards out there can poke all of the holes in this they want. Makes no difference to me, just what I learned and the actual number of degrees are not THAT important.

Does that help at all? It all sounds kinda wordy to me but if I need to clarify anything, I'll just pick some different words.

cheers eh!

Steve Kubien

Re: tool extension from your jig

#17

Re: Jamieson seminar

Steven Kubien

>Thanks Ed. That's what I thought but I wasn't sure.

Cheers,

Steve Kubien

Re: tool extension from your jig

#18

Re: tool extension from your jig

Texian

>John,

No time to read all those posts, so this has probably been covered, but--- with home-made jig with fixed angle of the "rotating" arm, may be necessary to extend tool several inches beyond the "block" to achieve "Ellsworth" or whatever "fingernail" grind. One can mark the block location on the tool with felt-tip marker. Have not been struck by lightning for ignoring the "2-inch extension rule", so maybe it is safe to try.