Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Norm Abrams

Posts

Re: Norm Abrams

#2

Steven Antonucci

Having watched Norm turn over the years...

steve antonucci

>I must say that he's gotten a lot better! Some of the early stuff reminded me of some of my early stuff...

S

Re: Norm Abrams

#3

Re: Norm Abrams

Jim

>I have to disagree with one thing he said on that preview... I don't think the morse taper is a "safety feature" designed to slip in event of a catch...

Re: Norm Abrams

#4

Re: Norm Abrams

Dick Coers

>I always thought Norm could get better on the lathe if he could somehow use a brad nailer to hold the stock on the lathe "for good measure". Oh the power of the boob tube..............

Re: Norm Abrams

#5

Re: Norm Abrams

john lucas

>I think he needs a gas powered electric chisel. Or he could use a air powered hammer chisel.

Seriously I have to agree he has gotten a lot better over the years. I always enjoy his shows.

Re: Norm Abrams

#6

Re: Norm Abrams

eliot d

>You can say what you want about "Old Normie", but it was only after I watched him on TV that I bought my first table saw and got into this whole woodworking thing. As with many of us, wood turning came later, and I have gotten a huge amount of pleasure from both flat work and lathe turning. So I take my hat off to Norm. To be honest , though, I think I will stick to the "names" in wood turning for my video purchases.

Re: Norm Abrams

#7

Re: Norm Abrams

Barry Irby

>I'm not sure, but I think I recall watching the show where he demonstrated turning something for the first time. He said he had little or no experience turning and did not consider himself a turner. He went on to turn something and I believe he also showed a duplicator.

I have been turning a long time. Pretty much self taught in high school shop over forty years ago. Attended demos by Raffin and others and a week with David Ellsworth at Arrowmont. I still would not want you guys watching me on TV.

Re: Norm Abrams

#8

Yes

Ron in Drums PA

>I was woodworking before Norm's NYW. I always watched his shows up until I started turning. I used some of his ideas and techniques as the basis of some of my flat work.

On one of his shows he did a drop leaf table. I liked it, made some changes and built it. When it was complete, I jokingly said to my wife that I couldn't find the right knobs for the drawers and if I had a lathe I would turn some with the wood I had left over from the legs. That's where she got the idea to purchase me a lathe.

I never did turn those knobs, but I still have the blanks.

Re: Norm Abrams

#9

Dick Hines

Re: Norm Abrams

Dick Hines

>I have always wanted to see the "out takes" from his show. I know he can not make as many cuts as he does and not make a mistake. That is a vidio I would buy.

Re: Norm Abrams

#10

Re: Norm Abrams

Barry Irby

>Me too. He cuts a miter and it fits. I cut one, and re-cut it, and trim it, and take a few thousandths off, and buzz it with the saw taking off an invisible amount, throw it away and make another.

Re: Norm Abrams

#11

Re: Norm Abrams

Paul Zerjay

>Did you ever notice theres no clocks in Norm's shop? And you can never tell if its morning, noon or night. I always wondered how many of the exact same shirts he has in his T.V. wardrobe. What he does in one half hour episode, would take me three days to do, and he's always got the same shirt on.

Re: Norm Abrams

#12

Re: Norm Abrams

Ed in Sptbg.

>I always wondered why he applies finishes with all the hardware mounted in place!

Re: Norm Abrams

#13

Nick Cook on YouTube for free *LINK*

Gordon Seto

>I would rather watch Nick Cook on the lathe.

Norm allowed his gouge to bounce in and out following the contour of the blank. I don't think he was comfortable with the lathe; he had the white knuckle death grip of the tool. Nick was graceful dancing with the tools, what a difference!

Either Norm was wrong on letting the Morse taper to slip during a catch. Or Oneway marketing the "safe drive" that we don't need.

I admit I have made enough catches to be self appointed semi-expert in catches. Either the work is held by the chuck or a Morse Taper spur drive, it makes no difference. If it is spur drive, the spur would still rip the wood first. If it is a Steb drive, the teeth would cut a ring. The dead center or Safe drive would slip during a catch.

Some of videos on YouTube are horrible; they should be labeled as what not to do. But if I am going to pay $25 for a DVD to keep, I would be picky.


Nick Cook on YouTube

Re: Norm Abrams

#14

norm is a class gentleman

robert davis

>

Re: Norm Abrams

#15

Never did get the drawers open either, right?

Steven Kubien

>

Re: Norm Abrams

#16

Now, You Guys Play Nicely

Barbara Gill, Remlik VA

>Norm has done a lot to promote woodworking. :-)

All the same type shirts are a good thing. Makes dressing easy.

Re: Norm Abrams

#17

Re: Norm Abrams

Ralph

>There really aren't any outtakes, according to the producers and team, Norm seldom, ever, makes a mistake.

You can watch them shooting on the NYW web-site. They really do much in a (very) long day

Re: Norm Abrams

#18

Re: Norm Abrams

don at central illinois

>I heard that someone asked Norm if he ever made a mistake and his response was, "None that you'll ever see."

Re: Norm Abrams

#19

Steven Antonucci

Undenialble contribution to woodworking

steve antonucci

>

Re: Norm Abrams

#20

Ditto what steve said

john lucas

>

Re: Norm Abrams

#21

Dick Hines

Re: Norm Abrams

Dick Hines

>I will never say Norm is not a class act. I just think that with all the cuts he makes he screws up once in a while. As my Daddy used to say,"People who don't make mistakes don't do anything." Boy am I donig a lot!