Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

OT: Metal cutting question

Posts

OT: Metal cutting question

#1

Steven Antonucci

OT: Metal cutting question

steve antonucci

>I need to cut some steel tubes (4) that are about 1.5" in diameter. I wondered if there was any downsize to getting a small metal cutting blade and mounting it in my tablesaw? One time deal.

Any better ideas welcome- my tubing cutters (plumbing) aren't big enough, and it needs to look half way decent.

Thanks

Steven

Re: OT: Metal cutting question

#2

Re: OT: Metal cutting question

Peter Teubel

>A wood bandsaw will be geared (belted?) too fast for a metal blade. It'll heat up and dull quickly during a cut. You're better off using a Sawzall.

Re: OT: Metal cutting question

#3

Re: OT: Metal cutting question

Keith Newton------WebKitFormBoundary4C+dWf+EJaD4HT

>I use the abrasive blades in the hand held circular saws regularly, even have one in my Dewalt miter saw at the moment. However the sparks will burn up the little dust elbow in back.

If you use the miter saw, it works best to have a shot piece of wood under the metal on both sides of the blade, so the kerf opens as the cut allows the ends to sag.

I will occasionally cut metal on the TS, but only on my little contractor saw. It takes too long to totally clean every little pocket of dust from every crevice on the unisaw, and PM.

Caution: Make sure there are no volatile chemicals open within 10' and or steel wool.

Re: OT: Metal cutting question

#4

Re: OT: Metal cutting question

Brian Hahn in SW Wisconsin

>The only type of metal cutting blade I've seen for a table saw are the abrasive wheels. Your choice, but I would never, never, never ever put one of those in my table saw.

For small tubing like that, I'd use a hack saw. Probably take less time too.

Re: OT: Metal cutting question

#5

Re: OT: Metal cutting question

Bill Hale / The Wood Spinner

>Steve

Either a sawsall with a metal blade or a high speed grinder with an abrasive blade. And there is always the old hacksaw.

Be really careful of the sparks in the wood shop. Take it outside if you are using power tools.

Good turning and be safe

Bill in CG, AZ.

Re: OT: Metal cutting question

#6

Skill Saw

Jorge Castaneda~Downeast Maine

>Steve,

They sell abrasive cutters for metal, put one on your skill saw and you are in business, instead of trying to push it into the metal, use a plunge cut, like you would in a chop saw, find a windy spot and place yourself to windward and wear heavy clothes, a hat and face shield and gloves... don't ask me how I have come to need all those.

It gets very hot and may blue your pipes.

Re: OT: Metal cutting question

#7

Re: OT: Metal cutting question

Ken Grunke from SW WI

>Steve, the tableaw would be my last choice for metal cutting but if you must, I'd use a thin reinforced abrasive cutoff wheel. Clean up the sawdust below so you don't start a fire.

I vote for the sawzall but a jigsaw will do OK.

Re: OT: Metal cutting question

#8

Re: OT: Metal cutting question

John K Jordan

>>Either a sawsall with a metal blade...

Milwaukee makes a metal-cutting blade for reciprocating saws called The Torch which is the first thing I grab for most small metal cutting jobs in mild steel. It surprised me how well this works.

If I need to cut more or thicker, I use a "port-a-band" saw which is a marvelous thing to have around, although a bit expensive if you don't cut metal often. I will only use abrasive wheels as a last resort with very thick stock - the Dewalt cutoff saw I have will throw sparks for 20 feet which is a real fire hazard, worse than a cutting torch I think.

JKJ

Re: OT: Metal cutting question

#9

Re: OT: Metal cutting question

john lucas

>STeve I've tried them all. Take it to a machine shop and have then cut it. I muffler shop will also be able to cut it quickly and neatly. As everyone else has said, if you use it on the table saw you have to clean every piece of wood dust with about 5 feet of the saw. It produces huge amounts of sparks.

An angle grinder with cutoff wheel will cut it but won't be any more accurate and not much faster than a decent hacksaw.

Re: OT: Metal cutting question

#10

Re: OT: Metal cutting question *LINK*

SteveP

>I purchased a small cut off saw from Northern Tool. It works very well. It looks alot like a grinder with a 7 inch metal cutoff wheel mounted to a base. It is under $50, depending on how many cuts you need to make it can be very worth while.


7" Chop Saw

Re: OT: Metal cutting question

#11

Clamp your tubing

Clem Wixted, Jonesboro, AR

>Make sure that the tubing, no matter what method you use, is clamped so it can't roll or twist on you.

Clem

Re: OT: Metal cutting question

#12

Steven Antonucci

Thanks to everyone

steve antonucci

>Just before running to HD, I remembered buying a cheapo grinder at a show. It was $20 or less, and had a bunch of things- one being a cutoff wheel.

I had already thought about the shower of sparks, so I swept the area "good enough" and went at it in a practice area. Cut perfect (enough).

Thanks for all of your help.

Steven

P.S. My son's Ikea loft bed is 14" shorter than they sell it...

:-)

Re: OT: Metal cutting question

#13

Re: OT: Metal cutting question

Walter Ahlgrim

>I use an abrasive blade in my table saw to cut 2 small ceramic tiles it was not 3 months later that bearing began squealing and had to be replaced, a coincidence I think not.

Should take about 5 minutes each with a hack saw, if the wall thickness is less than 1/8 inch and its mild steel firmly clamped with a good sharp blade. But the reciprocating saw would be my first choice.

Walta

Re: OT: Metal cutting question

#14

Re: OT: Metal cutting question

Barry Irby

>I was at a tool repair place they sell a saw blade for cutting metal. Comes in sizes that will fit a Skilsaw or a ten incher for a chop saw or table saw. I was stunned. Its got carbide teeth and is rated for about 3600 RPM. I did not see them in action, but the guys there were taking about cutting angle irons and rebar. I want one, but have no immediate use for it. They did say it was stunningly nasty. Would not run it on my TS though. I cut some copper and aluminum on my bandsaw. MISTAKE! Took forever to get the filings out of the rubber on the wheels. NEVER AGAIN.

Re: OT: Metal cutting question

#15

Pipe cutter ?

Pete in Holland, MI

>

Re: OT: Metal cutting question

#16

Re: OT: A TABLE saw?

Mark Mandell - Gone Round In Jersey

>Jeez, what some people will do to commit suicide!

Steve, if you need a nice clean cut on your pipe, take your stock over to a weld shop and they'll cut it for you on the horizontal band saw.

PLEASE don't try using woodworking tools!

mm

Re: OT: Metal cutting question

#17

Tube Cutting Tip

Ed in Leaside

>To mark a tube for cutting free-hand with a hacksaw: wrap a piece of paper around the tube and cut to the paper's edge.

Re: OT: Metal cutting question

#18

Dick Hines

Re: OT: Metal cutting question

Dick Hines

>See if you can find someone who will loan you their Saws All. That would be the safest way to cut the tubing. If you can't get a loaner buy one. I have one and use for all knid of things around the house.

Re: OT: Metal cutting question

#19

Re: OT: Metal cutting question

eaglesc

>I picked up a "porta band" at HF for $50.00 when they went on sale a few years ago.

The price has gone up and it isn't a Milwaukee but for the amount of metal I cut it is handy to have.

One mobile base out of scrounged bed frame made using their saw and wire welder just about paid for the tools.

I have also used both for making my own tool rests.

Re: OT: Metal cutting question

#20

Re: OT: Metal cutting question *LINK*

eaglesc

>Brain fart


"porta" band saw cheap.

Re: OT: Metal cutting question

#21

Re: OT: Metal cutting question

Chet Bisno

>Harbor Freight has a large selection of abrasive wheels that will fit a hand held grinder (5/8")arbor.

They frequently have a 14" abrasive cutoff chop saw on sale (~$50 sale price) that should work. I use them both to cut and shape High Speed steel scrapers.

The same caution applies about flamable objects that could be set off by sparks.

Chet