Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

chainsaw sharpening, help needed

Posts

chainsaw sharpening, help needed

#1

chainsaw sharpening, help needed

gary s clarke

>What is the best way to sharpen my chainsaw? Has anyone used a Granberg bar-mount shain saw sharpener? It can be seen for sale at Northern equipment and looks like it might help avoid the $9.00 to have comercial sharpening done. thanks in advance.

Re: chainsaw sharpening, help needed

#2

Re: chainsaw sharpening, help needed

Texian

>Gary,

Some think it's not good to sharpen the chain still on the bar, as some of the residue will end up in the slot between the chain and the bar. Another way is to clamp a couple teeth in the vice, sharpen, move chain and repeat. One relatively easy way is to use the appropriate file in a cordless drill (with chain in vice), and hold free end of file w/ a scrap wood block. Note pattern of file teeth and set drill direction accordingly.

Re: chainsaw sharpening, help needed

#3

Re: chainsaw sharpening, help needed

Bill Crommett

>I guess that I never appreciated my Stihl dealers $3.00 per chain sharpening service until he went out of business. His building got bought out for space for a Walgreens store. I haven't filed a chain in ten years except once out in the field when I nicked a stone. I did have to grind down the rakers a couple of times because he said the company would not allow him to do that.

Re: chainsaw sharpening, help needed

#4

Re: chainsaw sharpening, help needed

John K Jordan

>>...What is the best way to sharpen my chainsaw?

You'll get widely varied opinions! My idea of the best way is to hit each tooth a lick or two with a file every time or every other time the gas tank is filled. That's very quick, keeps the chain sharp, and gives the mind and body a little break. This is the way all the tree guys I know work. There are some simple file jigs to help keep the file aligned properly, if needed. For badly damaged chains (hit the rock or barbed wire), a stone in a Dremel works great.

I don't like to take the chain somewhere to be sharpened on a grinder since 1) it takes so long, 2) it's usually put off too long causing you to work with a dull chain, 3) it costs money, and 4), they almost always grind every tooth to the length of the shortest which is unnecessary and shortens chain life.

JKJ

Re: chainsaw sharpening, help needed

#5

Re: chainsaw sharpening, help needed *LINK*

Dick Coers

>I think you're right John, cause I never did like using a stone in a Dremel. The stone will glaze over very quickly and stop cutting. Add to that any dust or bar oil on the tooth and the stone will glaze faster. I bought a grinder from Baileys a couple of years ago. It was tough to justify a $150 grinder when I was paying $4 for each sharpening, but now all my chains are sharp when I go to the log pile and that puts a smile on my face. "Life is too short to use dull chains"! They don't have the model I bought anymore, but this is the replacement.


speedmaster sharpener

Re: chainsaw sharpening, help needed

#6

some sharpening tips

Robin Corell in Atascadero, CA

>I'm not sure which type of chain sharpener you have in mind. There are two types that clamp onto the bar. One uses a small grinder similar to a Dremel with a stone and the other uses a file. The kind with a file is actually more accurate than the one with the stone. But for your purposes accuracy is not that important. I use the type with a file for my milling saw to true up the angles after every three of four free hand sharpening. But for the majority of my sharpening I use a file freehand.

Some of the newer types of chain have a line etched on the top of the tooth. It serves two purposes, first is a reference line for sharpening and second is a safety marker to let you know when the chain is used up. The angles are not overly critical but you do want to use the appropriate size file. And as the teeth get smaller you may need to change sizes of files. This is very important because too large a file will change the angle on the underside of the tooth and if it becomes too obtuse it can become more prone to kick back.

One of the things that will affect the accuracy more than consistent angles is filing or grinding from the wrong side. On a chainsaw you want a burr on the edge and you want it on the outside of each tooth. This means that every other tooth needs to be sharpened from the opposite side. The easiest way to do this is to use a sharpie to mark a tooth and sharpen all the right hand cutters and then turn the saw around and file all the left hand cutters. When using a file I only file in one direction and rotate the file a bit each time. I usually take three or four strokes on each tooth. Rotating the file a little on each stroke helps the file wear evenly and therefore makes counting your strokes more likely to remove the same amount of material from each tooth. On a small bar this is not an issue but it is still best to wear out the file evenly, and keep in mind that chain files are an expendable item. Also do yourself a favor and make or buy a file handle.

You will need to take a bit off the depth rakers every so often. They make a file guide for this and it really is best to pick one up to learn with. it is easy to get carried away or take too much off the rakers and this can really slow down the cutting speed as well as make it more prone to kick backs.

Don't be intimidated to sharpen your own chains, it is not difficult but it does need to be done correctly or it can make a dangerous tool even more dangerous.

Robin

Re: chainsaw sharpening, help needed

#7

speedmaster sharpener

John K Jordan

>I don't even see that model in the new Bailey's catalog that came this week, but they do have two other models that are less expensive that may work fine for home use, one $100 and the other $120.

But a file is only a buck fifty!

JKJ

Re: chainsaw sharpening, help needed

#8

Re: chainsaw sharpening, help needed *LINK*

Cyril Griesbach

>I bought this one from Harbor Freight. I know...HF is poor quality but it was only about $35 and at the $5 my dealer was charging along with cutting an expensive chain down to nothing I thought "what the heck".

It's working great for me, it's quick, reasonably accurate and now I could scrap it without any loss based on chains sharpened.


Harbor Freight

Re: chainsaw sharpening, help needed

#9

Thanks, Robin. Most helpful. : )

Ruth Niles

>

Re: chainsaw sharpening, help needed

#10

Re: chainsaw sharpening, help needed

Brian Hahn in SW Wisconsin

>Robin gave some excellent advice.

I sharpen with a file and a file guide that clips onto the file, the type you see wherever chainsaws are sold. Just like everything else, it takes a little practice. I like to sharpen with the saw bar clamped in a vise and the chain on the saw.

Re: chainsaw sharpening, help needed

#11

Re: chainsaw sharpening, help needed

robo hippy

>It really isn't very difficult to sharpen a chainsaw with a hand file. It does take a little practice. Don't let the chain get too dull, unless you hit some rock or metal. You cut on the push stroke, and push from the low to the high point of the bevel. Don't push too hard. And wear gloves to protect your hands from cuts if you slip with the file. Try to find some one who can do it, and watch and get comments from them. The angle marks on the chain are really helpful.

robo hippy

Re: chainsaw sharpening, help needed

#12

Re: What robo said, and very important...

Jamie Donaldson

>....to have the exact size file need for your gauge chain.