Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Serious Sycamore

Posts

Serious Sycamore

#1

Serious Sycamore

Mark Mandell - Gone Round In Jersey

>Just got this spalted beast mounted. Currently 24+" in diameter, but mounted with the off-center pithe on the lathe axis and have some other defects to work out. Hoping for a 20" sphere. Will be starting at about 80rpm.


img

Re: Serious Sycamore

#2

Wow...

Jay in TX

>Mark,

Nice branch you got there on that mini-lathe. After you get it down to 20", then even I (or more accurately, my lathe) could handle it... barely (if I had more than 10 minutes to spare; I have to take study breaks or I'd pass out and most likely break the laptop).

Re: Serious Sycamore

#3

Re: Serious Sycamore

Brian Hahn in SW Wisconsin

>That will keep you busy for a couple of minutes. Have you thought about using the pipe trick for shaping the sphere? ;=)

Re: Serious Sycamore

#4

Pipe Trick

Mark Mandell - Gone Round In Jersey

>Very small bell iis ringing but I can't remember it.

Remind me on the Pipe Trick?

|;-}

[CRS runs deep in New Jersey]

Re: Serious Sycamore

#5

Re: Pipe Trick

Brian Hahn in SW Wisconsin

>A couple of recent threads have been about using a sharpened pipe to make small spheres. I figure for something the size if that blank, a 16" - 18" diameter pipe should be just about right. Doesn't everyone have a chunk of hardened steel pipe like that just sitting around waiting to be used?

Obviously, I was just kidding.

That chunk is going to take a little work to get it round and even more to hollow it. Good luck with it.

Re: Serious Sycamore

#6

Re: Good Trick

Mark Mandell - Gone Round In Jersey

>Since it took the overhead winch to get this thing on the lathe, I suppose I counld rig up an hydrolic holder to mount that pipe . . .

nah, gouges will just have to do.

Hollowing will be an issue because while it is mounted with the pithe on the centerline, hollowing it will be at about a 45* angle. The "roughed" sphere will have to be remounted and wood left at the contact/mounting point that can be removed after the hollowing is done. Yeah, this is going to be interesting all right.

mm

Re: Serious Sycamore

#7

Interesting indeed.

Brian Hahn in SW Wisconsin

>Yes, that is going to be a bit of a challenge.

I assume you are turning green and letting it warp. The final shape should be interesting. I hope it works out and you can post the results.

Hint: To get the degree symbol on a PC, hold down the alt key and type 248 on the numeric key pad. The degree symbol appears when you release the alt key. (I did a bit of software in a previous life.)

Re: Serious Sycamore

#8

Re: You're not trying to make a .......

Jamie Donaldson

>..."perfect" sphere out of sycamore I hope? That sucker will warp 2" or so as you turn it if it acts like most sycamore I have turned! Good luck!

Re: Serious Sycamore

#9

Re: Game Plan

Mark Mandell - Gone Round In Jersey

>I'm probably going to work it to a cylinder with the current mounting, to get the drying "even" in regard to the pithe, then change the fix point to set the hollowing axis angle (thanks for the typing tip), and then complete the sphere.

My largest boring bar for the hollowing rig is 1" and the plan is to hollow the sphere to about 2" thick walls to allow for carving. That's an 18" reach over the rest/gate so I may have to pick up a heavier (1-1/4") bar.

Also have to make a BA set of calipers to check the diameters.

I start making a mess tonight!!

mm

Re: Serious Sycamore

#10

Re: I Sure Am

Mark Mandell - Gone Round In Jersey

>And I certainly hope it does just that (in fact 3" would be even better) as that's part the idea. I'll also get a bunch of checking, but hope that I can keep them on the small side.

mm

Re: Serious Sycamore

#11

Marks' sphere, PIC *LINK*

John K Jordan

>David Marks told me once he was working on a big redwood sphere and it was a challenge. I see that Jim Barrett on Sawmill Creek posted a photo of the finished sphere, message in the link below. He said it weighed almost 400 lbs before hollowing.

Here's a link to the message itself.

http://www.sawmillcreek.org/showthread.php?t=18296

Don't forget to wear your safety glasses!!! ;]

JKJ


Photo of David Marks' sphere

Re: Serious Sycamore

#12

Re: Marks' sphere

Mark Mandell - Gone Round In Jersey

>Yup, that looks to be about the right size |;-}}}} Must remember to ask David how that piece turned out.

I think mere "glasses" will be rather ineffective in this instance; a personal forcefield would be nice though. I put this on an 8" faceplate with 12 #12 screws. With a 150lb blank, I'm taking no chances with a drive center slipping. I'll still feel a lot better when I get it balanced in spindle mode.

mm

Re: Serious Sycamore

#13

Alt 248 doesn't work on mine. XP Pro.

Allen Neighbors

>

Re: Serious Sycamore

#14

let's think about this

Tom Sontag - St. Louis

>IF the pith is centered, and IF the perimeter of the sphere landed on the same annual ring all around (at its equator), wouldn't the drying process just give you a football shape? Take away either prerequisite and sure you will get odd warping, but if close on both points, do you really expect 3" of movement?

Re: Serious Sycamore

#15

Re: let's think about this

Mark Mandell - Gone Round In Jersey

>Sycamore has a radial shrinkage rate of 5% (8.5% tangential). While I will start with the piece round for purposes of hollowing to an even wall thickness, I'm hoping to get as much movement to the oval as possible. There is a sycamore taken down near me that is 50+"in diameter (twice this size) but to use some of it for a piece like I have planned, I'd have trouble in predicting and controlling the grain and the shape change. Here I know the ends will "push out" as the diameter shrinks and that's already incorporated into the design of the final piece. I doubt I'll get more than an 1 to 1-1/2" change (given the 5% radial), but however much I get will be a help.

mm

Re: Serious Sycamore

#16

It's a matter of �

John K Jordan

>Did you remember to use the Numeric Key Pad instead of the numeric keys across the top of the keyboard? Also, did you hold down the Alt key while pressing all three numbers in turn, then release the Alt key? (Some people press and release the Alt key before typing the number keys)

I tried this on three different machines (Win2K, XP, Vista) and it worked the same on each. On a laptop without a numeric keypad I had to hold down Fn+Alt then type 248 on the embedded numeric keypad, then release all three keys.

Note that you can also open the Character Map application (under Accessories) and pick one or more characters, click Select, click Copy, then paste into your application. The � character is about in the middle of row 6 on my machines.

If you have enough screen space to open the browser and Character Map at the same time, you can drag the ČђσГ▲ċ�єҐ to your message composition window. This is the way I often work since I use dual monitors.

JKJ

Re: Serious Sycamore

#17

Brad Vietje

No Can Go There...

Brad Vietje

>Hi-Ho JKJ,

Can you cut and paste a photo ? I can't remember what password, user name or whatever I used to use to access Sawmill Creek, so I can't access that link.

Much obliged,

Brad Vietje

Newbury, VT

Re: Serious Sycamore

#18

Re: It's a matter of � Browser?

Jorge Castaneda~Downeast Maine

>What browser are you using John? It does not work in Firefox running in Win XP Pro, instead it closes the window when the alt key is released.

Re: Serious Sycamore

#19

Re: No Can Go There...

John K Jordan

>>...Can you cut and paste a photo ?

Do you mean you can't access the sphere photo? (attached below)

I don't read the Sawmill Creek, but googling for David Marks' sphere turned up that link. Funny thing, when I first went to the site it wouldn't let me in without registering, but after bumbling around a bit it must have changed it's mind and let me access the messages and photos.

JKJ


img

Re: Serious Sycamore

#20

Re: It's a matter of � Browser?

John K Jordan

>>...It does not work in Firefox running in Win XP Pro

Sorry, I don't have that combination at the moment. I tried it with Firefox in Win2K, and with IE in in Win2K, XP Pro, and Vista.

But the copy/paste or drag from Character Map should work, right?

JKJ

Re: Serious Sycamore

#21

Yes, Thanks!

Jorge Castaneda~Downeast Maine

>

Re: Serious Sycamore

#22

Esfera para Mark *LINK*

Jorge Castaneda~Downeast Maine

>mira aqui:

Una esfera muy bien hecha.


Esfera

Re: Serious Sycamore

#23

Laptop, Dell Inspiron 8600

Allen Neighbors

>It doesn't matter... FN+ALT+Imbedded Key Pad...numbers then release... nothing...

It's easier to type "degrees".

Thanks anyway.

Re: Serious Sycamore

#24

I can't even find the Character Map. :(

Allen Neighbors

>

Re: Serious Sycamore

#25

Start, All Programs, Accesories...

Jorge Castaneda~Downeast Maine

>System Tools, Char Map.