Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Morse taper arbor *LINK*

Posts

Morse taper arbor *LINK*

#1

Morse taper arbor *LINK*

john lucas

>This is the Morse taper adaptor I was talking about the other day for putting a grinding wheel on a lathe. It's also handy for other things.


http://www.sears.com/shc/s/p_10153_12605_00929850000P?keyword=009-29850&sLevel=0

Re: Morse taper arbor *LINK*

#2

Re: Morse taper arbor

Ed Larson

>John

Is the morse taper end threaded so it can be held in the head stock???

Re: Morse taper arbor *LINK*

#3

Re: Morse taper arbor

Barry Irby

>I have had one for so long I have no idea where I got it, but it was probably from Sears. Mine has a No. 1 taper, but I use it with a 2 to 1 adapter. (changed lathes) It does not have a threaded hole for the draw bar, but I bring the tailstock up and use the little dimple in the end of the shaft. Better supported that way anyway. Very handy once in a while.

Re: Morse taper arbor *LINK*

#4

Re: Morse taper arbor

john lucas

>I don't know for sure. The one I had before came with a jacops chuck threaded for 1/2" to fit the arbor and it was tapped on the tang end. I'm going to order one of these this week so I'll let you know when I get it. They come in #1 and #2 morse taper.

Re: Morse taper arbor *LINK*

#5

Re: Morse taper arbor

don lewonczyk

>The one I got from sears about 40 years ago isn't tapped for a draw bar through the head stock, I just used mine with a hard buffing wheel to polish my gun barrels after my house burned in 1977.DonL

Re: Morse taper arbor *LINK*

#6

Re: Another Morse taper arbor *LINK*

Peter Hyde

>Here's the LV one. Slightly more expensive but made in Canada and it is threaded for a draw bar.


Arbor

Re: Morse taper arbor *LINK*

#7

Let's Be A Bit MORE Careful Here

Mark Mandell - Gone Round In Jersey

>There's a very good reason that grinders' wheels are enclosed in metal. Grind wheels have a rather nasty tendency to fracture in use and then functionally explode in an eye-blink with no warning. If anyone here has experienced a piece of wood coming apart on the lathe, you ain't seen nothing and probably won't but your next of kin will if you use a grind stone this way.

Aside from getting fine abrasive material into your lathe bearings or scoring your morse taper (or both), these MT arbors are meant for buffing and stropping wheels. They're not intended to spin an abrasive wheel with the same precision that your grinder will, and it will be nearly impossible to balance the wheel for a good grind.

Take the few step over to your grinder, and leave your stones where they belong.

Rant Off

mm

Re: Morse taper arbor *LINK*

#8

Re: Let's Be A Bit MORE Careful Here

John K Jordan

>>...Grind wheels have a rather nasty tendency to fracture in use

Not only in use, but sometimes when new out of the box! This is true of wheels for bench grinders, side angle grinders, etc. This is the reason manufacturers recommend a step some people omit - when first mounting a wheel, stand off to the side and turn on the motor at the highest speed if not fixed. (Just like after first mounting a bowl or blank on a lathe, imagine that!) Let it run for a while and see if it blows up. I think the usual recommendation is to let it run for about one minute.

I have never had one come apart but I always test. This is a reason to always use a full face shield instead of just safety glasses when grinding.

JKJ

Re: Morse taper arbor *LINK*

#9

I couldn't agree more Mark.

Ron in Drums PA

>I have a arbor like the one in the above link and all it should ever be use it for is to mount buffing wheels.

Putting a stone on this arbor could be suicide.

Re: Morse taper arbor *LINK*

#10

Re: A good grinder wheel without.....

Jamie Donaldson

>...any cracks will "ring" when struck lightly before mounting, and a wheel with a crack will have a dull"thunk" when struck. That's a good test to perform before mounting on the motor arbors.

Re: Morse taper arbor *LINK*

#11

Re: Another Morse taper arbor

jgrounds

>Wondering if the Lee Valley arbor or the one from Sears is available is available in both right and left hand threads. The adds do not mention this detail.