Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Small spheres with a tube gouge

Posts

Small spheres with a tube gouge

#1

Small spheres with a tube gouge

John K Jordan

>As per the discussion on spheres, I tried making a small tube gouge from a piece of steel pipe. The pipe was about 0.36" ID (9mm). I ground a bevel on the outside leaving a sharp edge on the inner diameter.

I tried making some small spheres from a variety of woods as shown below. Turned out they were very quick and easy to make. The spheres in the photo are more or less 1/2" (about 12mm) in diameter. I used a small detail gouge to make rough beads close to the right size then turned them into nice spheres with the tube.

Things I learned:

--- The tube acts more like a scraper than a gouge. I first tried my Termite tool which has the bevel on the inside of the ring and it was a disaster. It kept trying to cut into the sphere.

--- The edge on the tube needs to be as smoothly honed as possible, otherwise it will put deep scratches on the sphere. (Duh) After first attempting to sharpen in on a grinding wheel, I chucked the tube up on the lathe and while it was spinning I ground the bevel with a rotating sanding disk. I then honed with a diamond hone. I sharpened both ends so I could switch when one end got a little dull. I cleaned up the inside of the tube with a round file.

--- The sphere must be somewhat larger than the tube ID or it will catch and bind and break the sphere from the supporting wood.

--- With the cutting edge of the tube in contact with the wood, swing the back end back and forth to shape the sphere. It was a little easier to hold the tube against the tool rest, but not absolutely necessary.

--- It worked a little better if I rotated the tube (around it's long axis) while working it back and forth over the surface of the sphere. I'd like to try spinning the tube slowly in an electric drill.

--- Little wood spheres will roll right off a bandsaw table and get lost in the shavings around the lathe!! The five shown below are what I have left after making eight!

--- It was FAR FAR easier to turn a decent sphere with the tube than to try to get it spherical with a skew or detail gouge.

The little spheres in the photo are black cherry, cocobolo, ebony, holly, and pink flame, all more or less 1/2" in diameter.

Good clean fun!

JKJ


img

Re: Small spheres with a tube gouge

#2

Those are cool, John. Thanks!

Eddie Pacheco; San Jose, Ca.

>I have some seamless 3/8" and 1/2" dia. stainless steel tubing I can try that with. Thanks for posting this and giving a description of the process.

Re: Small spheres with a tube gouge

#3

Those are nice looking little spheres.

Brian Hahn in SW Wisconsin

>Thanks for the report. I'll have to try it again - on small stuff this time.

Re: Small spheres with a tube gouge

#4

Steven Antonucci

That's so cool.

steve antonucci

>Great! Another tool I need to go make...

Steven

Re: Small spheres with a tube gouge

#5

Re: Small spheres with a tube gouge

john lucas

>Cool John. When I tried it I used a 1 1/2" diameter pipe. It was very hard to control but I'll try a smaller one and see what happens.

Re: Small spheres with a tube gouge

#6

Re: OK Jen, here's the solution for you!

Jamie Donaldson

>

Re: Small spheres with a tube gouge

#7

Small spheres with a tube gouge-home made marbles

georgetroy

>

Re: Small spheres with a tube gouge

#8

Re: Small spheres with a tube gouge

GaryG in MD

>Thanks John, That looks like fun. Gotta try it. Very cool. Good work. ...Gary

Re: Small spheres with a tube gouge

#9

Re: Small spheres with a tube gouge

George Van

>Nice looking spheres John. Was this a piece of conduit?

Re: Small spheres with a tube gouge

#10

Re: Small spheres with a tube gouge

John K Jordan

>>...Was this a piece of conduit?

No, a piece of tubing I had around. Looked like stainless to me (no rust) but a magnet does stick to it.

JKJ

Re: Small spheres with a tube gouge

#11

There it is!

Steven Kubien

>Now I have a use for all those little bits of left-over pen blanks.

Cheers,

Steve

Re: Small spheres with a tube gouge

#12

Re: Small spheres with a tube gouge

Don at Central Illinois

>What angle is on the tube? Or I wonder if it matters what angle it is. Really cool, thanks John.

Re: Small spheres with a tube gouge

#13

JL

Re: Why? (other than to show you..

JL

>could do it :)).

Re: Small spheres with a tube gouge

#14

Awesome!

Jennifer@Indy.USA

>John are you kidding me! These are wonderful! What kind of tube is that?

I am going to have to check this out. Thank you so much.

Jen :)

Re: Small spheres with a tube gouge

#15

Re: Small spheres with a tube gouge

Jennifer@Indy.USA

>Thanks John, I'll keep my eyes open for something suitable.

Re: Small spheres with a tube gouge

#16

Re: Small spheres with a tube gouge

George Van

>Thanks John, I thought conduit would be too thin and soft ;-)

Re: Small spheres with a tube gouge

#17

Re: Why? (other than to show you..

john lucas

>JL ever tried to turn a perfect sphere that size. It's really rough and Jen needs a bunch.

Re: Small spheres with a tube gouge

#18

JL

Re: I know it is tough!....

JL

>I'm not doubting that. I'm just wondering what you use small spheres for. Is is for decoration?

Re: Small spheres with a tube gouge

#19

see Jen's post on the prior thread

Mark in B'ham, AL

>

Re: Small spheres with a tube gouge

#20

Re: Small spheres with a tube gouge

John K Jordan

>>...I'll keep my eyes open for something suitable.

I'm going to test this tubing to see if it can be hardened so it will hold an edge much longer. If so, and you can't find something, I could send you a piece of this - I have about 3' left. However, I think you wanted to make smaller spheres, right? (1/4" - 3/8"?)

Someone with a metalworking lathe could probably machine one of these from the right kind of steel and properly harden it for a much better tool.

JKJ

Re: Small spheres with a tube gouge

#21

Keith Tompkins

Re: Small spheres with a tube gouge

Keith Tompkins

>Thats funny John, I'm in the process of using 1/4" balls in my latest pieces....great minds must think alike!