Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Turning tools ??

Posts

Turning tools ??

#1

Turning tools ??

Wayne

>Is there a place where one could see pictures of the different turning tools and there uses. I have a set but they didn't cost but 100 bucks, they are a set with 8 different tools. I assume that 4 are gouges one is what I would call a parting tool two skews one that is diamond shape and one that look like a scraper although it doesn't look like the square ended ones I see on the net it has about a 60 degree bevel. Any help would be appreciated. It would be nice not to just to grab one that looks right and start cutting.

Re: Turning tools ??

#2

Steven Antonucci

It is probably better to learn what each tool can

steve antonucci

>do in your hands, instead of what they are "used for". Some people use tools very differently, and just because it's a spindle gouge doesn't mean you can use it on a bowl. Knowing what you can do with a tool is something that happens over time...

As an example, I own a roughing gouge, but I do almost all of my roughing with a bowl gouge. I've seen people use the wings of a roughing gouge like a skew...

Steven

Re: Turning tools ??

#3

The question I wished I'd answered...

Jay in Tx

>Wayne,

When I posed a similar question in the past, I got a question in reply (rude woodworkers! ;~) The question was, "What do you want to do? Got a project in mind? Boy I sure wish I'd have answered that question before accumulating a plethora of one trick ponies, latest gizmos, and things to do things I didn't know enough about to know that I wouldn't enjoy doing them.

Want to turn a bowl? A box? Turn a bead on them? Put some 'intentional' chatter on them (still trying to figure that one out)?

Bed posts? Candle sticks? Trivets? Cutting boards? Spheres? etc.?

Well let all these fine gentlemen, ladies, and me know and we'll do our best to put you on the right track for different tools, methods, and techniques. Steve had it right... what the tool can do just depends on the user (and a little bit of the laws of physics). But if you just like to look at and fondle tools, I got a few whatchamadingles I'll part with at less than retail prices...

Re: Turning tools ??

#4

Re: The question I wished I'd answered...

Wayne

>my reason for asking is I built a Grandfather clock a couple years ago and everything went ok until I had to turn the spindles. They are made of red oak and it was a real challenge I needed 4 and ended up turning 10 and still had the beads with chips in them. I figured it was bad technique but maybe it was the tool I used. Some tools seem to be better for doing certain things.

Re: Turning tools ??

#5

JL

Re: Turning tools ??

JL

>One of the best places to start is a book by the late Keith Rowley - "Woodturning: A Foundation Course". It has pictures and how to use the tools. There are many other good books. There are a number of good DVDs that you could buy.

You can also take a class somewhere.

You could post pictures of your different tools and ask what people use them for (and how) - you'll get a few different answers (and generate a lot of discussion) :).

Re: Turning tools ??

#6

Re: Turning tools ??

Darryl

>agree with the other comments. Probably the only one we might agree on is the diamond shape one that is used to part off a piece when it is done. Raffan's books are good as well as many others. Where are you located there is probably a "club" or chapter of woodturners near you who would be pleased to help, show and answer questions.

Re: Turning tools ??

#7

Re: Turning tools ??

don lewonczyk

>If you just want a brief explaination and a picture of the tools order the catalog from craft supplies USA 1-800-551-8876. In the front section of the book there is a tool selection guide, its a good place to start and costs nothing and in the tool section ther are more pictures. Like one guy said there are so many gizmos and gadgets out there it gets confusing and expensive. Have fun looking. DonL

Re: Turning tools ??

#8

Steven Antonucci

I've turned beads with

steve antonucci

>a skew

a bowl gougle

a scraper

a spindle gouge

a detail gouge

a point tool

a bedan

and a parting tool

Are some of these tools better than other for beads? Yes, but in the right hands they all work very well.

Were they always my perfect tool? No, and I've actually broken:

a bowl gouge

a roughing gouge

a scraper

because I didn't understand or couldn't manipulate the tool correctly.

Steven

Practice with what you have.

Re: Turning tools ??

#9

Re: Turning tools ?? *LINK*

John K Jordan

>Wayne,

You might do what I did when starting with the lathe. I got some good books, two to start with, either would do the trick: Fundamentals of Woodturning by Mike Darlow, and Turning Wood by Richard Raffan. These books show each tool and how to use it, then describe various practice exercises, e.g., how to turn beads, bowls, etc. Videos are good too, but the books have so much more information.

There's a lot of info on the web. The link below has good pictures and info.

This resource link has enough reading for all day: http://www.woodturns.com/resources/woodturning.htm

You might also try to find a club in your area. If you say where you live, someone may know of good resources in your area.

As for your experience with chipped beads on red oak, beads can be turned with several tools but the MOST important thing is the tools must be very sharp. Woodturning and sharpening are inseparable.

JKJ


beginners guide to woodturning

Re: Turning tools ??

#10

Re: Turning tools ?? *LINK*

Gordon Seto

>Turning is a compound 3-D motion that you need to roll, advance and lift the tool at the same time. For me it is difficult to comprehend just by reading. The first choice would be working with a mentor.

http://www.woodturner.org/community/chapters/members.pl?submit=Chapter+List

Most clubs have library of books and DVDs for members to borrow and almost free hands-on program.

These YouTube videos by Nick Cook are really good. But not all on YouTube are good. Some are just demonstrating what not to do without declaring so.

Safety first. You don't want to find out know danger warnings from your own accidents in your experiments. Here is some resource information:

http://www.woodturnerscatalog.com/store/util/resource_center?Args=

Gordon


Nick Cook on YouTube

Re: Turning tools ??

#11

Re: Turning tools ??

eliot d

>One thing to keep in mind is that red oak is very "chippy"; white oak turns smoother.