Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

mini lathe variable speed motor conversion

Posts

mini lathe variable speed motor conversion

#1

mini lathe variable speed motor conversion

Carol - now in NC Nebraska

>OK, I think I am ready and have everything at hand to proceed.

To recap (and ask my questions): several years ago Randy at Vega offered some variable speed treadmill motors that could be used to convert the single speed motor to a variable speed motor, particularly on the Jet mini-lathe (as I recall).

Well, I bought a couple.

Who actually has done this? And after all this time what is your verdict? Was it worth it? What would you have done differently?

Please offer your 20-20 hindsight before surgery on my mini begins.

Thanks!

Re: mini lathe variable speed motor conversion

#2

Re: mini lathe variable speed motor conversion *LINK*

Jeff Taylor, Bloomington IN

>I have no purchased this product, mainly because I had not seen it until this morning ..

I was browsing the Penn State Industries site for something else, and found this in the catalog .. for $99 it seems to be complete ..

I might have to grab one while it is on sale, for use in my old Delta ..


PSI variable speed motor info

Re: mini lathe variable speed motor conversion

#3

Re: mini lathe variable speed motor conversion

Bill Hale / The Wood Spinner

>Carol

The only problem you will have is the motor RPM. I believe you will find it has a top speed of 10,00 RPM. If this be the case you will need to add a jack shaft to slow it down. I have an old Atlas that I did this to and it works great.

Be sure the motor has the fan or it will get hot with prolonged usage.

You may find the $ 99.00 to Pen State to be easier.

Good turning and be safe

Bill in CG, AZ.

Re: mini lathe variable speed motor conversion

#4

Re: mini lathe variable speed motor conversion

john lucas

>Carol I'm only batting 30 percent. I used the first motor to drive a slow speed drive so we could rotate a basketball player slowly to produce a video and then later tried using it to make short videos of art work for the web.

Then I bought 2 for myself and have somehow killed the power supplies. I can't seem to find more power supplies and can't really afford to pay someone to find the problem and fix these so as of right now I'm sorta stick with 2 motors and no good power supplies.

I'm rethinking my options for that lathe now.

Re: mini lathe variable speed motor conversion

#5

Re: mini lathe variable speed motor conversion

eaglesc

>An IAP member FredNC made a conversion on a jet mini.I don't recall if he posts here or not.

About the PSI conversion motor.

They had a great idea except the slowest speed that motor goes to is 750 rpms.

Why go through all that trouble to make an after market conversion and then produce a product with the slowest speed faster than the slowest speed is on a stock JET mini?

I have a manual JET mini and the slowest speed is 530 rpm's.

Re: mini lathe variable speed motor conversion

#6

Re: mini lathe variable speed motor conversion

Bill Howatt

>Well, here I go out on a limb with a bit of speculation since I don't own a Jet mini. If the VS motor is mounted in place of the regular motor and the spindle is driven via the step pulleys then you will be able to obtain a lower speed with the VS motor since the normal induction motor probably is a 1725 RPM motor. Also, the pulleys will give increased torque at low speed.

My 20", 2HP General has a 4-step pulley system with it for this very reason. It also keeps the motor RPM up for better fan cooling as well.

Bill

Re: mini lathe variable speed motor conversion

#7

Re: mini lathe variable speed motor conversion

Carole Valentine

>Heck woman, do you want to turn or do you just want to keep building jigs and modifying tools and machines??? LOL Just get on the thing and start making shavings! We have waited long enough to see your first HF! ;) You don't NEED VS - it takes what - 20 seconds to flip the belt? You don't NEED a vac chuck or a captured hollowing system to turn. I have neither, and don't see a NEED for them. In fact you are probably better off to learn the art of hand hollowing first(unless there is a physical reason for not doing so) as well as all the traditional means of holding a work piece before you jump into buying/building/modifying stuff. Go out there and make some shavings and post some pictures of what was left! :>)

Re: mini lathe variable speed motor conversion

#8

Re: lathe renovation purposes

Carol - now in NC Nebraska

>You have a point, friend.

Unfortunately is way too darn cold to try to turn. I have had to haul everything into the house that might freeze to no good effect. I can't keep the garage above freezing.

Planning this project helps keep my mind sane, because I can do this in the house where it is almost warm. This place has a heat pump and it cannot keep up with single digit temperatures. Right now I am parked in front of the computer and in front of a space heater in a tiny bedroom I call an office. This is a recipe for going stir crazy!

Planning projects helps. It's what I did when I was in school and had no tools on hand. Here I have a few tools and I am slowly collecting supplies. I did turn a couple of things before Christmas, some for Christmas presents. And as soon as it warms up, I will be back out there as my schedule allows.

Hollow forms? The goal at the moment is boxes. It is what I have wood for. When I get back to Arizona, I will hook up with Wally again for the next hollow form lesson. :)

Now before I haul the lathe onto the kitchen counter and begin surgery, I wanted some experienced opinions. I could be talked out of this, if the benefits are marginal or non-existent.

But thanks for cheering me on, to get out there and make chips, and see what's left. :)

Re: mini lathe variable speed motor conversion

#9

Re: lathe renovation purposes

Carole Valentine

>So clamp that sucker down on the kitchen counter and start turning! LOL You should see my den floor right now - I have been playing with a Ryobi power carver I got today. The dog doesn't care and the cat is playing with the chips. I "may" suck it all up with the vac before I go to bed, but then I may not...I may let Sally chase chips all night. That's one of the privileges of living with just furry companions. :)

Re: mini lathe variable speed motor conversion

#10

PSI kit is very good

Bill Turpin in WNC mountains

>I got the PSI kit for my wife's Fisch mini. I had to drill two motor mount holes in existing adjustment plate. It took longer to get the old pulley off (heat-removable Locktite) than the rest of the project. I was able to use both of the old pulleys. Motor shaft is � 14.1 mm. We get about 20 rpm at slowest. I turned an 8" x 2" bowl in red maple with a 1/2" bowl gouge. Intentional test, trying to stall it, yielded about a 5% slow down, but it kept on trucking! This lathe has been used about twenty hrs/week since conversion in mid October. Absolutely no problems with conversion. Total conversion 1.5 hours.

If you decide to do this...BE SURE THAT you make the centering jigs before you tear apart your lathe for the project. Also use the existing power switch to start and stop the lathe. Power the input to the new control box with the output to the old motor. That way you do not need to re-train muscle memory as to where the switch is. Use rare earth magnets to attach the new box until you decide where you want it. Use the new box to control only the speed for a few days, leave it always turned on.

Bill in WNC mountains

Re: mini lathe variable speed motor conversion

#11

Re: mini lathe variable speed motor conversion

Wayne

>I got a motor out of a treadmill and used it for a grinder I used the circuit board and a reastat to control the speed works great I have to be real careful to lower the speed after it starts or I will have to repair something and go the doctor. They really have a lot of torque but the slow speed really makes grinding chisels and plane blades a lot easier. My motor is a DC motor.

Re: mini lathe variable speed motor conversion

#12

Re: lathe renovation purposes

john lucas

>Carol I understand perfectly. It's too cold in my shop to work tonight so I'm doing other things. I often make sketches or reread old magazines looking for that perfect idea or new technique that I missed the first time through.

I also think one of the things I have always enjoyed about woodworking is solving the problems and learning new techniques. I would love to say something philisophical like I turn to release the inner me and let the wood be my voice but I'm just to redneck for all that. I like woodworking because I get to play with tools, invent things, and learn new ideas.

If I ever get lucky and actually produce a piece of art that someone will buy then maybe I can worry about the philosophy thing.

Stay Warm. John

Re: mini lathe variable speed motor conversion

#13

Re: lathe renovation purposes

Carol - now in NC Nebraska

>Great idea, but I am renting, and actually the church is paying the rent. I don't want to think about what would happen if I got caught turning in the living room/kitchen (read - large open area). Bad enough I have a bunch of tools, motor, wires, connectors, etc. on the kitchen counter now!

And this is a duplex. The landlord's grandmother lives next door. And this is a small town. Life in a fish bowl.

Good idea - bad idea. :(

Re: mini lathe variable speed motor conversion

#14

Re: PSI kit is very good

Carol - now in NC Nebraska

>Might be good, Bill, but I already have everything for the home brew version, and I don't want to spend another $100. :)

Re: mini lathe variable speed motor conversion

#15

Re: mini lathe variable speed motor conversion

Carol - now in NC Nebraska

>I got two of those motors, Wayne, and that is exactly what I have done with one of them. Super slick sharpener. Mine is a powered scary sharp system with ten "wheels" of different grits - from 60 to tripoli on leather.

A friend brought me a 1" inexpensive bevel chisel from the borg with deep machining marks. In 8 minutes we had a mirror back and a sharper than a razor edge. He was amazed! I touch up my chisels in seconds, once the back has a mirror finish.

I'm thinking about getting the HF set of turning tools just to practice sharpening those free hand on this system. Once I have learned that I will subject the good turning tools to it.

Re: mini lathe variable speed motor conversion

#16

Re: lathe renovation purposes

Carol - now in NC Nebraska

>No philosophy here either, John.

I just like to occupy myself with things I enjoy, which do include re-inventing, improving, and tinkering with tools. I'd love to make chips, but...all things in their time. And temps in the single digits ain't the time! LOL!

Our minds travel in some of the same paths.

Re: mini lathe variable speed motor conversion

#17

Re: mini lathe variable speed motor conversion

Wayne Carson "TX"

>I wonder if it would be possible to use the motor for a direct drive for a lathe no pulleys. I knew that old treadmill would be good for something, I didn't like it for what it was intended for!!

Re: mini lathe variable speed motor conversion

#18

Re: mini lathe variable speed motor conversion

Carol - now in NC Nebraska

>No, I don't think so. The spindle is too small and the bearings are not intended for the same thrusts.

Same question came up on Family Woodworking a couple of weeks ago.

But it would also make a dandy sharpener!

Re: mini lathe variable speed motor conversion

#19

Re: mini lathe variable speed motor conversion

Wayne Carson "TX"

>I have my grinding wheel directly on the motor shaft. I had a piece machined to the dia. of the motor shaft and threaded for a nut and washers no pulleys. I was taulking about using it on a lathe direct drive.

Re: mini lathe variable speed motor conversion

#20

If you will look at specs I think the minimum

henthorn

>speed is 650 rpm. For me that is worthless. That is way too fast for some of the things you need to do on your lathe. The Jet VS only has a minimum speed of 500 rpm. Again that is far too fast for me.

Re: mini lathe variable speed motor conversion

#21

I think the ones Carol is talking about

henthorn

>have controllers which can reduce the speed to 0. Or am I mistaken?

Re: mini lathe variable speed motor conversion

#22

The Vega package was a DC motor with controller

henthorn

>that can reduce the speed down to 0.

Re: mini lathe variable speed motor conversion

#23

Re: mini lathe variable speed motor conversion

HaveWoodWillTurn

>John: Resolder every trace on the circuit board. I scraped the varnish off the trace a little before doing this. Cold solder joints are a real problem with these boards (I think that's why they went to the surplus pile). I suspect you'll have working units again. PM me if you wish.

Ed