Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Drilling a depth hole

Posts

Drilling a depth hole

#1

Steven Antonucci

Drilling a depth hole

steve antonucci

>I've used several kinds of drill bits and they all wander. For smaller hollowforms, I have been using a spindle gouge and I personally think it's the easiest and best way to drill a starter hole.

So my question- what's the longest spindle gouge on the market? I don't need a a lot of flute length, just the overall length. I also don't think it needs to be that "beefy", but I'm thinking along the lines of 12" to 15" of steel.

Anyone know of such a beast, or do I have a date with a grinding wheel?

Steven

Re: Drilling a depth hole

#2

Re: Drilling a depth hole

Paul Zerjay

>I bought a 3/8" drill bit about 15" long and put a handle on it. It doesn't wander too bad and its really fast.Just make sure you keep removing the shavings or it will get stuck and twist right out of your hand. DAMHIKT

Re: Drilling a depth hole

#3

Re: Drilling a depth hole

Dick Coers

>Steve,

I've never tried one, but I think that just the ticket for this work is a gun drill. There's one on Ebay that's over 1/2" and over 14" long. Price seems better than a gouge too, less than $15 now. Maybe there is an industrial surplus place around you for a better deal.

Re: Drilling a depth hole

#4

Re: I have run air through a gun drill

Al Crandall -NW of Indy-

>I drilled 15" deep in about 1/2 minute by just pushing the entire tailstock along the bed while running air through a shop made adapter for a gun drill. I really needed the face mask I was wearing.

Re: Drilling a depth hole

#5

A "D" Bit

Jorge Castaneda~Downeast Maine

>it is nothing more than a drill rod with an end grind to half its diameter exactly for a couple inches, and the front grind to an eccentric point to prevent wandering.

You make a starter point and then drive the D bit through the tail stock, once you have the hole deep enough, you get rid of the tail stock.

Thrust and withdraw, thrust and withdraw... You need to get rid of the shavings or will heat up very much.

I have made 24" holes this way, and come out very close to right on and it does not take that long. 3" of O1 drill rod is a few bucks from ENCO.

I did not harden or temper it and drilled in black wood and granadillo.

Jorge

picture when I find it in my old computer

Re: Drilling a depth hole

#6

Re: A "D" Bit

Jorge Castaneda~Downeast Maine

>Here it is.

This is what we used in a flute making class.


img

Re: Drilling a depth hole

#7

Steven Antonucci

I can make that!

steve antonucci

>oh, joy! Iget to make another tool. Is the flat area all the way up to the tip, or does the tip have a small, offcenter gouge profile?

And finally, do you use it in a small starter hole or as is?

Thanks for posting.

Steven

Enco order is on the way... and will have to be reallocated to make one of these!

Re: Drilling a depth hole

#8

Re: I can make that!

Jorge Castaneda~Downeast Maine

>You are welcome Steve,

Yes, it is flat all the way to the tip and the front is ground like a scraper, a little more acute.

The starter hole I make with a brad point drill, about 1/2" deep,

I hold the D bit with a vise grip.

very simple and effective.

Have fun!

Jorge

Re: Drilling a depth hole

#9

Mike Stafford

Re: Drilling a depth hole

Mike Stafford

>Steve, I have no idea what the longest spindle gouge on the market is but I have a wonderful Henry Taylor detail gouge in a 1/2" flute that I use for both hollowing and drilling the center hole of boxes. It has an 8" flute and is strong enough to extend quite a ways over the tool rest for hollowing boxes without chatter. It has become my "go to" tool.

Re: Drilling a depth hole

#10

"D" bit *LINK*

John K Jordan

>One of my books has details of how to make a "d" bit, but dang, I think I lost some bits in my memory and can't put my finger on it. I have a vague memory that the flat is not ground exactly halfway through the bar but I can't remember if it is less or more than 1/2.

I found this which might be useful.


Long hole boring

Re: Drilling a depth hole

#11

Lamp Auger?

Ron McKinley

>What about a lamp auger? I've got one but have never used it. I bought it to make a few lamps but so far never got a "roundtuit."

Re: Drilling a depth hole

#12

Re: Drilling a depth hole

eliot d

>If all you want to do is remove some wood from the center of a hollow form, why do you care if the drill bit wanders a bit? You're going to remove all that wood anyway. I'm sorry if I've missed something.

Re: Drilling a depth hole

#13

Steven Antonucci

C'mon Eliot- You're a Duck!

steve antonucci

>Engineering answer:

Accuracy - I'm turning to thin walls, and if I miss the bottom, I either end up with a nub or a hole. Getting the bottom of a pot to be 1/8" thick is probably the most challenging thing to do in hollowing.

If I'm off by 1/8" on the bottom, the pot feels dumpy like a Weeble. If I have that nub in the middle, I'll always know it's there, not matter how small the entry hole.

Re: Drilling a depth hole

#14

Re: C'mon Eliot- You're a Duck!

eliot d

>I'm a duck? Why am I a duck? What did I do? I still don't understand your problem: getting thin walls can be done with a laser set-up, or by careful measurement with other mechanical means. But drilling the entry hole is not the issue. The entry hole just gets some wood out of the way so you can proceed with the hollowing, no? One of the really neat things about a laser method is that you can position the laser dot right at the edge of the tool cutting edge when you're down at the bottom and see exactly how deep you are cutting. Then just part off an eight of an inch further towards the head stock. I think this is more of an engineering approach than most other methods. I must still be missing something!

Re: Drilling a depth hole

#15

Steven Antonucci

Stevens Tech mascot is a Duck!

steve antonucci

>I drill my entry hole to "final depth" so that when I no longer see the predrilled hole, I stop cutting in the middle. It also helps prevent getting a cone in the middle of the form that can't be removed.

A laser is another means of measuring, but most of the rigs I've seen are for captured units, not handheld. Even then, most of the lasers throw a dot that is +/- 1/16", and under normal circumstances the wood flexing at RPMs don't make this any more accurate than feeling with a wire caliper with the lathe stopped. Easier, maybe, but no more accurate. I might rig up a laser pen to a dowel to measure the bottom with the lathe off, but that's as close as I see me coming usng a laser.

Steven

Re: Drilling a depth hole

#16

Re: Stevens Tech mascot is a Duck!

eliot d

>Let's just stick to getting the bottom an eight inch thick for a moment. This was your original concern. Very well. So WITH THE LATHE OFF ( no vibration now) set the laser dot to the edge of the cutting tip and insert it so it just touches where you have stopped cutting at the bottom. Now make a mark 3/16" further back toward the headstock and part off. Then when you reverse chuck and clean up, you should have your 1/8" thick bottom. This is a better engineering solution( your preference) than just using a stick because it eliminates the errors associated with eyeballing the edge of the stick when you bring it out of the vessel and try to line it up outside the vessel toward the bottom. There's a fellow in my club who made a measuring tool , using a laser, just to do this very thing. I never saw why he went through the trouble because I can do exactly the same thing with my cutting tool and laser as described above. Either way represents an excellent way to get the bottom thickness just right.

Do you know that I attended Stevens Institute of Technology? Is that the "duck" reference?

Re: Drilling a depth hole

#17

Steven Antonucci

A laser only makes sense on a captured cutter...

steve antonucci

>which is not something I use. I handhold my tools. Adding a laser rig and dealing with having to hold it parallel to the ways while cutting on a handheld setup is impossible. If the setup isn't perfectly parallel to the ways, it introduces error.

But back to the original requirement, which was an accurate way to drill a depth hole to within an 1/8" of a finished bottom. The laser doesn't really buy me anything unless I attach it to the drill, right, since I am not trying to measure the bottom, but drill an accurate hole within a specified tolerance. If I don't, I'll have a cone at the bottom that can't be removed without "run back" danger from cutting back towards the center. I've lost many a vessel to this through a small hole...

Steve

P.S. You mentioned that you were a Stevens Grad in a past thread in response to me mentioning that I was a Stevens Grad. My 20 year anniversary is coming, and I might just go to Alumni Weekend this year...

Re: Drilling a depth hole

#18

Re: A laser only makes sense on a captured cutter.

eliot d

>I see your point. Lasers are best used with a captured rig of some type.

So what did you decide is best for drilling an accurate hole?

ps

Actually, I'm not a Stevens alumni. My Alma Mater is Cornell University. But I did graduate work at Stevens. I earned a PhD in mathematics in 1969 there, and I have fond memories of Stevens and Castle Point Station.

Regards,

Eliot

Re: Drilling a depth hole

#19

Steven Antonucci

I am still using the drill close and measure often

steve antonucci

>method. If I get close I can muscle out any lumps in the middle. I've actually flipped the cutter in an angled Ellsworth hollower and turned the bar upside down to cut towards center with a measure of success. Just have to be careful to not create an inverted cone ;-)

Steven

P.S. Half a duck is better than no duck at all :-)

Re: Drilling a depth hole

#20

Re: Drilling a depth hole

Mark Mandell - Gone Round In Jersey

>Steve,

I use a 1/2" brad point in a TS drill chuck to do the first 3" and then switch to a 18x1/2" installer's bit that will go to 16". The initial hole serves as the centering guide and I move the TS in 3" stages to advance until my bit gets to the point I mark on the drill shaft with tape. Have gone to 12" this way in dry maple burl with no appreciable wandering at about 500rpm. Do have to back out the dust before each advance, and I don't put undue pressure on the bit.

mm

Re: Drilling a depth hole

#21

Steven Antonucci

What's an installer's bit?

steve antonucci

>Never heard the term?

Thanks

Steve

Re: Drilling a depth hole

#22

Installer's Bit

Mark Mandell - Gone Round In Jersey

>18 to 24" long bit used to go through floors and framing to run wiring or plumbing. Fluted section is about 6" long. Must make sure that the drill check is ver well seated in the TS's taper. Any dirt or high spots in there or on the male insert will cause the chuck to turn and really screw up your taper surfaces.

There's also a line of auger-point drill bits used by electricians that can run to 60". They have a screw-threaded point that feeds into a twist-drill body about 4" long which in turn tapers down to a 3/8 or 1/4" shaft. They are self feeding but will wander a bit more than you would want.

mm

Re: Drilling a depth hole

#23

Dick Hines

Re: Installer's Bit

Dick Hines

>I use a paddle bit with the tip ground off. To sharpen I just grind it like a scraper.

Re: Drilling a depth hole

#24

Don Derry

Mark Mandell - Gone Round In Jersey

>Uses spade bits to "open" his turnings. He says they'll drill straight if care is taken to check the grinds, especially the outboard spurs to make sure they are even.

It works for him, but not for me. |;-}}

Re: Drilling a depth hole

#25

Spade bits work *LINK*

Jerry Hall

>well for me too in a hand held tool. I use a $6 Harbor Freight keyless chuck, bit extensions if I need it. I like a turned handle with a mushroom end for pushing, and a 1/2 x 24 machine screw, head sawed off, glued into the end to hold the chuck. The spade bit clears green wood dust better than other choices I have tried. Doesn't get too hot. Withdraw and clear regularly. Have to measure carefully with the bit's long leading point to not go to far in. Use 5/8" bit typically so that there is a clearance hole for the knuckle on the extension. Easy to sharpen by lightly grinding the outside face of the bit on each side. Does wander a little bit sometimes, but minimal with a good Irwin bit and sharp leading point. But who cares if it is exactly centered for a depth hole, as long as it covers the center well. Next best choice is a long 1/2" detail gouge, but it sure gets hot. Will have to try the suggestion to use larger bits to hog out more, but agree centering would have to be managed.

The holder also works well to hold shop made Alan wrench tools for captive rings and hollowing.


Keyless Chuck