Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Hunter Cutters

Posts

Hunter Cutters

#1

Hunter Cutters

Mark Mandell - Gone Round In Jersey

>Finally got my Hunter cutters mounted for my boring bars. This pic of the straight holder which is made from 9/16 O-1 drill rod. The 3/4" step-down is cut to .375 which fits the sockets drilled in my 1" and 3/4" boring bars. The bars are drilled off center to give maximum meat for the set screws. The cutter mounts were milled and then the cutters are bedded on a double layer of aluminum tape.


img

Re: Hunter Cutters

#2

Curved

Mark Mandell - Gone Round In Jersey

>This is the curved holder mounted in the 3/4" bar. The piece was machined first, then set in a vise and hot bent. When the curve is set level, the cutter is held at a 35* angle for the sheer cut. These cut very smoothly in dry box elder, so I'm sure they're going to make hollowing a whole lot easier.

mm


img

Re: Hunter Cutters

#3

Mike Stafford

Re: Curved

Mike Stafford

>Mike, those look wonderful. One suggestion I might make if you were to make another set. Cant the mounting surface downward 5 degrees and you will find an even greater improvement in the way the tool cuts.

Mike Hunter has been allowing me to test some swan neck tools and in going through the various prototypes the one that has been the most efficient and smoothest cutting are the ones with the cutter mounted with that downward slope of the cutter. You will also find that rotating them about 45 degrees to the axis of the shaft clockwise will also improve the cut.

I have also been able to test some 5mm cutters that fit the Sorby multi-tool and Hollowmaster and they are mounted at a 45 degree angle. They seem to be able to address the wood with more of a shearing cut in this orientation.

Re: Hunter Cutters

#4

Pitch, cant, tilt?

Mark Mandell - Gone Round In Jersey

>Mike,

When you refer to a cant, do you mean other than the radial angle? I can, of course, rotate them in the boring bar to whatever I want, but I think you're talking about the other axis. So, do you mean

nose down . . /

or

nose up . . \

relative to the centerline of the bar? I would think that a nose-up angle would bring the bevel into play and block the edge.

Thanks

mm

Re: Hunter Cutters

#5

Mike Stafford

Re: Pitch, cant, tilt?

Mike Stafford

>Of course you can rotate them. I am so geometrically challenged I did not even think of that.

No, I was referring to the mounting surface upon which the cutter is attached. If you machine it with a 5 degree downward tilt (nose down) you will get a much better shearing cut.

At least that is the case on the tools I am using that are in trials.

Re: Hunter Cutters

#6

Re: Nose down

Mark Mandell - Gone Round In Jersey

>Gotcha. We cut the back wall of the notches to the same angle as the bevel of the cutter. NBD to set this up as two cuts. I have two more 9/16" blanks, so it's easy to give them a try.

Thanks

mm

Re: Hunter Cutters

#7

Mike Hunter

Re: Pitch, cant, tilt?

Mike Hunter

>The words pitch, cant, tilt, etc do get confusing. The best defination understond by machinist is 45 degree side tilt and 5 degree front tilt.

Re: Hunter Cutters

#8

Mike Stafford

Thanks Mike!

Mike Stafford

>I should have raised the white flag when I was over my head. It was strictly a case of knowing what I thought I meant but not knowing how to say what I thought I knew....LOL!

Re: Hunter Cutters

#9

Dennis in Southern Oregon

Re: Nose down

Dennis in Southern Oregon

>Can someone possibly post a drawing that defines the geometry under discussion here? I, for one, have had a bit of trouble getting my new Hunter tip to do what I would like it to do. Dennis

Re: Hunter Cutters

#10

Mike Hunter

Re: Nose down

Mike Hunter

>Please send me your email address and I will email you a couple of pictures.