Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

John Jordan Hollowing Tool

Posts

John Jordan Hollowing Tool

#1

John Jordan Hollowing Tool

Barry Turner

>I bought the above at the TAW Symposium. I was in the shop this morning preparing to try out these tools and discovered that the tool bit in the gooseneck hollower was not very sharp. So, I decided to just sharpen the tool bit using the sharpening fixture that I also bought. I took the bit out and fastened it in the sharpening fixture.

I had assumed these jigs were designed to work with the Wolverine system, but I don't seem to be able to be able to get the right angle on the bit no matter where I positioned the Wolverine arm. Is there something else I need to do? The tool bit comes into contact very low on the grinding wheel, well below center. I even tried the bit in the fixture upside down, but that didn't work either.

I finally gave up and freehand sharpened the bit. I have to wonder if the fixture needs an extension on it's arm or something? What do you think? What am I doing wrong? Are there some instructions that I failed to get with my purchase? Thanks.

Re: John Jordan Hollowing Tool

#2

Re: John Jordan Hollowing Tool

Al Crandall -NW of Indy-

>I wasn't familiar with the shrpening jig you mentioned so I googled it. I came up with this picture:

http://www.stubbylathe.com/SharpeningJigInstructions.htm

If your relationship of cutter to wheel centerline is considerably different than as shown, maybe your Wolverine system is too far below the wheel. I cut off some of the bottom of the wheel guard on my grinder so that the system would mount higher (closer to the wheel) and not be too low. A quick fix for you would be to fabricate something to nest inside the vee pocket of the Wolverine system to raise the bottom end of the Jordan sharpening jig and get the cutter above the wheel centerline.

Even after having modified the guard, the pocket of the Wolverine was

lower than I wanted by 9/16" so I mounted a wood "v" in the pocket and held it in place with a stout rubber band. End of problem.

Re: John Jordan Hollowing Tool

#3

Re: John Jordan Hollowing Tool

Dave Peebles Lyons, Ohio!

>Hi Barry,

It looks to me that the jig is not used in the pocket of the Wolverine, but a dimple is made on the arm to get it in the right position. John mentions on his web site that you may have to bend the arm... (of his jig) to make it line up right.

Best wishes,

Dave

Re: John Jordan Hollowing Tool

#4

Re: John Jordan Hollowing Tool *LINK*

Gary Evans Tallassee, TN

>Hey Barry,

I'm not sure how John Jordan intends for his jig to be used, but Don Geiger sells an add-on for the Wolverine that allows the V pocket to be adjusted vertically as well as horizontally. It's a good addition for any Wolverine.

No real affiliation, though we are good friends.

Gary


Don Geiger's Vertical Solution

Re: John Jordan Hollowing Tool

#5

Re: John Jordan Hollowing Tool

john lucas

>Barry I'd give him a call on Monday. I'm sure he'd answer your question. He's in Antioch.

Re: John Jordan Hollowing Tool

#6

Re: John Jordan Hollowing Tool

Barry Turner

>Actually, he's in England, at least right now. I bought the tools and jiog at the symposium. Apparently, my jig had become separated from the instructions. I found the photos and instruction on his website last night. I think those instructions will allow me to get the jig up and running. Thanks for the help.

Re: John Jordan Hollowing Tool

#7

Thanks Everybody!

Barry Turner

>

Re: John Jordan Hollowing Tool

#8

Re: John Jordan Hollowing Tool

tek-Brunswick, Ohio

>I'm pretty sure his instructions should be good. I bought one of his jigs and it works well. Yes, you are supposed to put a dimple in the arm with a center punch. Johns idea is for you to keep the arm length set up for your bowl gouge and put the dimple where the angle would be right for the hollowing cutter jig. Then you do not need to reposition the jig to sharpen either one.

Re: John Jordan Hollowing Tool

#9

Kelton Sharpening Rig

Jorge Castaneda~Downeast Maine

>Al,

I love my Kelton rig,it has a post and can be raised or lowered, and for bowl gauges, it has a spherical socket and the jig proper has a ball in there, so it makes for a very smooth and infinitely adjustable.

Take a good look at it, I like it better than the wolverine.

Jorge