Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

new lathe on the market

Posts

new lathe on the market

#1

new lathe on the market

john lucas

>What do you think of this lathe? Looks interesting, especially for beginners.

http://www.grizzly.com/products/12-x-20-Heavy-Duty-Bench-Top-Wood-Lathe/G0658

does Jet or Rikon have one with variable speed yet, I haven't looked.

Re: new lathe on the market

#2

Re: new lathe on the market

Tommy Holmes

>It looks like it is set up for outboard turning..???

Re: new lathe on the market

#3

Re: new lathe on the market

Barry Irby

>It does look like it it set up for out board turning.

Wonder if you can add bed extensions? Does not look like the other end is milled to receive them. That would be a short coming. Many people turning spindles would like to be able to turn a 30" table leg.

Does it reverse? That would be nice for sanding.

And does the head stock pivot or rotate? Doesn't look like it. Seems like a couple of small things would have really taken it up a notch.

Looks good though.

Re: new lathe on the market

#4

Re: new lathe on the market

RevDoug

>Bottom end speed is a bit high as well for off balance bowl blanks.

Turn 'em round,

Re: new lathe on the market

#5

Re: new lathe on the market *LINK*

Gordon Seto

>Strange and unique design. The tool post is on the right of the banjo. It prevents the tool rest getting close to the work when hollowing bowls. I can't figure out what is the advantage of doing so. Other than that the specification looks good on paper. The outboard (if it works) is gravy.

Jet is coming out with the electronic VS version of the 1220. The slowest speed is going to be 270. That is a big advantage over their non-VS.

Gordon


Jet 1220 Variable Speed

Re: new lathe on the market

#6

Another new lathe on the market *LINK*

Scott in Montana

>I'm new to this forum so this might have appeared here before, but I didn't see anything in a search.

This is the new $1295 bench top bowl lathe from Vega. I have the model it replaced and love it. This model add the removable tail stock and a 1.25" spindle... and maybe more.

Scott


Vega 2413 B

Re: new lathe on the market

#7

JL

Re: new lathe on the market

JL

>Looks a lot like the General 25-200 variable speed "Maxi-Lathe".

Re: new lathe on the market

#8

Digtal Display

Jerry Hall

>on the head stock? Does this imply a VFD quality or DC drive? If so that would suggest decent torque at the low end? Or maybe it is just a simple digital tacometer? It is 110V input so it may be the same technology as the Jet Mini VS with torque limitations.

Re: new lathe on the market

#9

Re: Another new lathe on the market

keith zimmerman, Normal, IL

>I had an opportunity to turn a hollow form on the prototype for this lathe last fall and it had the makings of being a very good lathe. I really like the swing on this and the footprint makes it very usable in a small shop.

keithz

Re: new lathe on the market

#10

Re: Another new lathe on the market

keith zimmerman, Normal, IL

>I had an opportunity to turn a hollow form on the prototype for this lathe last fall and it had the makings of being a very good lathe. I really like the swing on this and the footprint makes it very usable in a small shop.

keithz

Re: new lathe on the market

#11

Dick Hines

Re: new lathe on the market

Dick Hines

>If I was in the market for a bench top lathe I would give the Old Griz a closer look.

I have a PM 3520 and a Jet mini so I can't see buying another lathe

Re: new lathe on the market

#12

Vega 2413 B, mid-sized bowl lathe

Scott in Montana

>Hello Keith,

In regards to the 2413B Vega lathe; what kind of base was the lathe attached to? As I mentioned, I have the model 24 which is very similar except for the tail stock. I haven't had any good ideas for a stand that didn't take up a lot of floor space that I don't have. Currently, I have a base made from 2x4's that I clamp to my heavy work bench. It works, but I'm sure there is a better solution.

Thanks,

Scott

Re: new lathe on the market

#13

Re: new lathe Delta Midi is no more

John Kyler

>We got word that the Delta Midi is no longer.

Guess this will help fill the void.

Re: new lathe on the market

#14

Re: new lathe on the market *LINK*

E.T.

>Here is a link to the 25-200. General has just released an upgraded model with headstock indexing and shaft locking. The general costs more but does go on sale and has a swivelling headstock. the motors look the same, from what I can see in the photos.

I am sooooo pleased with the performance of the one that I bought a year ago. ET


http://www.general.ca/pagemach/machines/25200a.html