Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Dust Collector /Turning problem?

Posts

Dust Collector /Turning problem?

#1

Dust Collector /Turning problem?

Barry Irby

>I have not hooked my DC up to the lathe or even made a hood for it. I bring the hose up close when I am sanding and hook it in the banjo, but other than that I just let the shavings fly and use the DC to vac them up with a four inch hose.

Yesterday I sucked up the shavings from a sycamore hollow form and noticed the DC making a sort of odd vibration/noise. My DC is outside in a small closet and the pipe for it comes straight through the wall. I pulled the fitting off the inside and found the impeller pretty well covered in nice stringy shavings. (Its a Delta 1 1/2hp unit with an upper filter bag and a lower plastic bag.) I reached in through the pipe (6" S & D PVC) and brushed the shavings off. Spun it up and then cleaned off the little bit that was left.

I have been using the DC in this set up for about three years. Never noticed this before. I am wondering if it would have cleared itself if I had left it alone? I also noticed the vanes were rough around the edges. Clearly just crude stampings with no effort to finish or smooth the edges. I am wondering if it would be worth while to file the edges smooth? Would they be less likely to grab stuff out of the air/would it slide off better? OTOH, I don't want to through it out of balance.

Re: Dust Collector /Turning problem?

#2

Re: Dust Collector /Turning problem?

Bill Hale / The Wood Spinner

>Bary

It seems the long curly wet stuff causes most of the problems. I did the same as you in the past but am now picking up the shavings into a 15 gal trash can and dumping them into a trailer. I do the final floor clean up with the vac. I think this method is even faster. I generate an average of 45 gal of shavings a day when I am doing rough out work. I set the trailer just outside my shop garage door.

Good turning and be safe

Bill in CG, AZ.

Re: Dust Collector /Turning problem?

#3

Re: Dust Collector /Turning problem?

Darryl

>Barry, wood shavings will erode plastic and soft metal vanes. Big ones will crack them. I use a two stage collection system. The piping from my lathe goes to a 30 gallon trash container then to the dust collector. I also use a "big gulp" thingy at the front of the lathe and some (not all by any means) of the chips go there then to the trash container so that only dust is picked up by the DC directly. Rube goldgergish I know but it really works. Only problem is lifting the trash con to get it outside to empty.

Re: Dust Collector /Turning problem?

#4

Hmmm!!!

Barry Irby

>Now that I think about it, I had a separator I made out of a Rubbermaid 32gal. trash can. It used to be hard to change the bag on my DC, so I made the separator. My shop is small so I rearranged the DC to make it easier to change the bag and ellimanated the separator.

Maybe what I should do is roll the separator back in when I want to vac up a bunch of wet curls.

Wonder if it would be better to walk on them for a while and let them dry out?

Re: Dust Collector /Turning problem?

#5

Re: Dust Collector /Turning problem?

robo hippy

>If you are generating chips rather than shavings, any dust collector will work for general clean up. If you are making shavings, especially with wet wood, they will jam up the impellers quickly. This is why there are 2 stage collectors, so all that stuff you don't want sucked up the hose won't go into the impellers (rags, sandpaper, cutoffs, etc). You should see (but hope you don't) what a 2 inch cube of wood can do to your impellers. It will bend metal ones and break the plastic ones. The hose will do okay for getting sanding dust on small things like pens, boxes, and small vases. When you get bigger, especially of you are power sanding bowls (which throws dust out at all angles), a big gulp thing, a vent, or a real hood will do a much better job of getting the dust before it gets into the rest of your shop. Generally, I use a big scoop shovel to pick up the shavings, and then sweep and shovel, then use the hose. Shavings are just a bit much for the DC to handle if you are turning volume.

robo hippy

Re: Dust Collector /Turning problem?

#6

Re: Dust Collector /Turning problem?

eaglesc

>make the closet bigger and put the separator next to it outside.

Re: Dust Collector /Turning problem?

#7

Keith Tompkins

Re: Dust Collector /Turning problem?

Keith Tompkins

>HI Barry, Be absolutley SURE the impeller has stopped before sticking your hand in to check for debris. I have the same unit; it will be dead silent, yet the impeller is still spinning fast enough to really cause some damage. Adding a large can in the system for heavy stuff to drop into ahead of the impeller helps.

Re: Dust Collector /Turning problem?

#8

Dick Hines

Re: Hmmm!!!

Dick Hines

>Barry, I just let then build up until the are even with the bed of my lathe. By then they are dry and I can clean them up easier. If you know anyone who has chickens I bet they would love to get your shavings. I have been hauling mine to the guy down the mountain from me for years.

Re: Dust Collector /Turning problem?

#9

go back to garbage can

robert davis

>