Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Hamilton Woodshow, Pens

Posts

Hamilton Woodshow, Pens

#1

Hamilton Woodshow, Pens

Jim Shaver Oakville, Ontario

>Hi,

This weekend is the annual Hamilton Woodshow. It's a great break to enjoy some wood things in the "post Christmas" winter season here. It's also fun for me, in the last few years as a member of the Golden Horseshow Woodturners Guild I have demonstrated pen turning at the show. At the booth I have met many other pen turners, sharing my process and sources of materials with whom ever asks. I enjoy sharing what I know.

These are a few of my best pens from yesterday, I turned 7 pens in 3-4 hours.

This is an amboyna burl on a rhodium Gentlemens pen, the blank is unstabilized (sourced from William Woodwrite).

Photobucket

Photobucket

I used Mylands sealer as the base to apply the CA finish to, then micro meshed and polished to a shine.

This is another Gentlemens pen, with a similar amboyna, but with some sap wood, same finish. These two blanks were cuts from a sequenced source, they are pairs.

Photobucket

Photobucket

This is a pen made with a stabilized amboyna, the heart wood was very dark, not really a characteristic of the stabilizing process, just a different tree.

Photobucket

Photobucket

It was a fun day, nice to turn in the warmth of the GHWG booth, it was enjoyable, even with 20 pluse peopel watching closely while you make those final delicate finish cuts with the skew.....and no, I didn't chip once!

:-)

Take care,

Jim

Re: Hamilton Woodshow, Pens

#2

Re: Hamilton Woodshow, Pens

Peter Hyde

>Here is Jim caught in the act!


img

Re: Hamilton Woodshow, Pens

#3

Andy DiPietro

Re: Hamilton Woodshow, Pens

Andy DiPietro

>WoW!! Beautiful job on the pens. You just have to love Amboyna Burl.

They all look great. I especially like the pen in Pic 3 & 4 because you have the sapwood and heartwood together.

Andy DiPietro

Re: Hamilton Woodshow, Pens

#4

Re: Hamilton Woodshow, Pens

Cyril Griesbach

>A real trio of beauties, Jim. What is your method of applying CA as a finish?

Re: Hamilton Woodshow, Pens

#5

Re: Hamilton Woodshow, Pens

Jim Shaver Oakville, Ontario

>Thanks Cyril,

My process for my finish begins after I finish turning I sand the blank with 320-400, then apply Mylands cellulose sealer with the lathe off, let it set up, then sand again with 400. I sand with the lathe at 500 RPM. Once I have done this first step I then start my CA finish.

I use THIN CA, apllied to a shop towel, with the off I quickly apply a very thin coat of CA and let it set up, I have never tried the BLO method, but this works fine for me.

After it is dry I apply a second thin coat of THIN CA, let it set up, then I wet sand with Micro Mesh, 3600-4000-6000-8000-12,000.

I then apply a third and final quick coat of THIN CA, let it set up, then I use Micro Mesh 8000-12,000, then turn the lathe up and polish at 2600 RPM with Novus 2. That's it.

With three thin coats though I have not built up a level clear coat. The finish I have here follows the topography of the wood and that may be a function of quickly applied thin coats of THIN CA.

This is what I do, it works for me....a few pen makers watched me apply this method to three of the pens I made yesterday, they all had done CA before with BLO and the lathe on, they all agreed they liked what I did. That is my method, milage may vary for others using this application.

Take care,

Jim

Re: Hamilton Woodshow, Pens

#6

Re: Hamilton Woodshow, Pens

Allen Neighbors

>Thanks, Peter, it's good to have a pretty face to go with those pretty pens. :))

Re: Hamilton Woodshow, Pens

#7

Re: Hamilton Woodshow, Pens

Allen Neighbors

>As is always the case, Jim Shaver, just gorgeous pens. It would be a shocker to see one of yours that wasn't. :)

Re: Hamilton Woodshow, Pens

#8

Re: Hamilton Woodshow, Pens

Mike Rubes, Apex, NC

>Hi Jim,

Sounds like a great day! I love the pens. I've turned a small amount of amboyna burl and really liked it. It takes a great polish. Very nice job on the pens and congrats for not "chipping" under pressure! I always get nervous when people are in the shop, I cannot imagine turning in front of a crowd :)

Mike

A little stagefright in Apex, NC!

Re: Hamilton Woodshow, Pens

#9

Re: Hamilton Woodshow, Pens

Dave Peebles Lyons, Ohio!

>Hi Jim,

All beauties as usual :)

Great pics too. It is good to see you back at the lathe. It seems you are feeling well after the surgery and have not lost the touch at all.

Dave

Re: Hamilton Woodshow, Pens

#10

Re: Hamilton Woodshow, Pens

Cyril Griesbach

>Thanks, Jim. It's copied, pasted and printed. Now if only I don't lose it.

Re: Hamilton Woodshow, Pens

#11

Thank You

Jim Shaver Oakville, Ontario

>Thanks to all of you for your thoughts....

Take care,

Jim

Re: Hamilton Woodshow, Pens

#12

Storing Turning Information

Mike Brazeau

>Cyril - I am finding the best place to store methods, projects etc. is on my computer. Sounds like you are half way there. In additon to printing,save the file with a file name that means something and has an easily identifiable keyword. Open a folder or series of Turning Folders in My Documents. I have some 25 folders for various turning topics. If you can't find it at a glance, just look using Microsoft Explorer's Search function. If you keep a series of keywords in your file names, stuff is easy to find. I am amazed how few people use the power locked up in ME.