Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Ambrosia Silver Maple HF

Posts

Ambrosia Silver Maple HF

#1

Andy DiPietro

Ambrosia Silver Maple HF

Andy DiPietro

>Hi Everyone,

I have been experimenting with shape and form on large vessels. This piece is Ambrosia Silver Maple and is 17 1/2" high x 11"dia x 3/16" wall and turned on the pith center. The collar has a 1 �� opening and the base is 2� dia.

I almost went through the bottom (1/32") so I backfilled with CA and sawdust. That could have been a really bad day or weekend. I applied 6 coats of Waterlox to give the finish depth. The white silvery chatoyance areas look like quilted figure but I do not know if that is the correct why to describe it. How would you describe that figure even though it is hard to see in the picture? Please comment on shape & form etc.

Thanks

Andy DiPietro


img

Re: Ambrosia Silver Maple HF

#2

Andy DiPietro

PIC2 Top View 

Andy DiPietro

>


img

Re: Ambrosia Silver Maple HF

#3

Re: Ambrosia Silver Maple HF

Ron in Drums PA

>At first I thought you added a collar, then when I enlarged the image I realized it was part of the wood.

Re: Ambrosia Silver Maple HF

#4

Re: Ambrosia Silver Maple HF

Ron in Drums PA

>Meant to say, great job on a great looking piece

Re: Ambrosia Silver Maple HF

#5

Re: Ambrosia Silver Maple HF

Dale Cook

>I think the form on this piece is very nice. I also like doing large pieces like this, It's very challenging.Great piece!

Re: Ambrosia Silver Maple HF

#6

Re: Ambrosia Silver Maple HF

George Van

>This is a very pleasing shape Andy, the 2" base is invisible! Before reading your description my question was to be "how do you get this to stand?"

Re: Ambrosia Silver Maple HF

#7

Re: Ambrosia Silver Maple HF

Bill Hale / The Wood Spinner

>Andy

Realy nice piece and finish. Don't you just love it when it all comes together.

Good turning and be safe

Bill in CG, AZ.

Re: Ambrosia Silver Maple HF

#8

Re: Ambrosia Silver Maple HF

Cyril Griesbach

>Andy, Nice wood and nice forms also. And...I don't know if I'm right or wrong, I call that kind of figure quilted too.

Re: Ambrosia Silver Maple HF

#9

Dick Hines

Re: Ambrosia Silver Maple HF

Dick Hines

>Andy I love the pieces. Nice shape and figure in the wood. Here is the only thing I would do differently. It has nothing to do with the shape. When you put your finish on why don't you pore some finish inside and slush it around. It stop the contrast between the finished wood and the non finished wood.

I like to finish the insides of my HF's . Just my opinion and you know about them.

Re: Ambrosia Silver Maple HF

#10

Very impressive

GaryG in MD

>Great form in such a large piece. Nice wood and finish. Love it. ...Gary

Re: Ambrosia Silver Maple HF

#11

Turning centered on the pith

Dinyar Chavda

>Andy:

Quick question re the fact that it is turned including the pith. Do you hae any problems (or take any steps to prevent) cracking?

Re: Ambrosia Silver Maple HF

#12

Andy DiPietro

Re: Turning centered on the pith

Andy DiPietro

>Hi Dinyar,

After I turn the piece between centers and form a tenion I CA glue the bottom. Then I mount it on a four jaw chuck. I worked on this piece for two days so I soaked in a bucket of water overnight and then finished it on the second day.

On the top side I center the pith and use a 1 3/4" opening for the collar. That size is usually large enough to remove the wood stresses. I occasionally spray the collar with water as I am hollowing so that it does not dry and crack on the lathe.

You also need to start with a recently felded tree or a waxed log where you cut off several inches off the ends to get green wood.

After I am finished hollowing I reverse the piece and finish the bottom. I then coat the bottom with CA glue. After that drys I coat the inside of the bottom by dribbling CA glue through the top collar.

I apply one coat of finish to the outside and let the pieces dry for 3 or 4 weeks before applying more finish coats. If you hollowed the bottom thin then you will still get a few small cracks that will need to be filled.

Hope this helps

Andy DiPietro