Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

locking lathe spindle - Mr. Crandall??

Posts

locking lathe spindle - Mr. Crandall??

#1

locking lathe spindle - Mr. Crandall??

Carol - now in NC Nebraska

>OK, since the min-lathe is going to undergo surgery anyway...

I have trouble with my arthritic hands (and lack of hand strength) in turning the blank on to the worm screw. The worm screw is in the chuck and the chuck is on the spindle. I have to hold the spindle and keep it from turning with one hand, and then try to turn the blank on to the worm screw with the other. Sadly, my hands are no longer up to that task.

How can I lock the spindle so I can use two hands to turn on the blank?

Exterior lock, largely in my way if I had any thoughts about trying to turn on the lathe with the lock in effect. Maybe in conjunction with an index plate somehow?

Thoughts?

Mr. Crandall? I defer to your genius.

Re: locking lathe spindle - Mr. Crandall??

#2

Re: locking lathe spindle - Mr. Crandall??

Dave Peebles Lyons, Ohio!

>Hi Carole,

I don't remember which lathe you have... Jet mini? But if you do, use the knockout rod inserted into the hole in the spindle collar next to the threads. Then just let it rotate to the back side of the lathe bed. This will prevent the spindle from rotating as you screw the blank on to the screw. Clear as mud ??

Best wishes,

Dave

Re: locking lathe spindle - Mr. Crandall??

#3

Re: locking lathe spindle - Mr. Crandall??

john lucas

>I'll send you a photo of my modification to the Jet mini. I'm leaving in a couple of minutes for the Taw woodturning symposium so it will have to be later tonight. I simply put a piece of steel on tip with a hole drilled in it so I could drop the spindle locking lever down through this and into the spindle. I screwed the steel plate to the top by drilling and tapping a couple of holes. It's easy to do.

Re: locking lathe spindle - Mr. Crandall??

#4

Re: locking lathe spindle - Mr. Crandall??

Barry Irby

>I don't have a mini lathe and I don't know which one you have so this is just speculation. If it has a hand wheel couldn't you use a strap wrench like the one designed for changing the oil filter in your car? Put the wrench on the hand wheel and let the handle rest on the stand?

My lathe has two holes through the hand wheel and you can stick the knock out bar through them so you can use it as a wrench. Could you do that with yours and provide a way to "chock" it?

Or, go at it the other way. Drill the hole for the screw in the blank, put it in place and bring the tail stock up. Then use the strap wrench to turn the hand wheel and screw the worm into the blank. Once it starts, use one hand to steady the blank and the other to turn the wheel.

Re: locking lathe spindle - Mr. Crandall??

#5

Use a Faceplate!!

Jorge Castaneda~Downeast Maine

>Carol,

A couple years ago, I read a post by Wally Dickerman about using a faceplate and glue block for making bowls, at the time I was intent in figuring out how to make platters, well, I followed his advice and don't use the screw chuck at all and the regular chuck only occasionally,

Give it a try

Jorge

who has gnarled arthritic hands

Re: locking lathe spindle - Mr. Crandall??

#6

Re: locking lathe spindle - Mr. Crandall??

Cyril Griesbach

>Carol, you may want to try this as an alternative as I rarely use the screw method.

Set your blank up between centers with the open end of the bowl facing the tailstock and using a parting tool turn a recess in the face of the bowl so you can expand the chuck in it. Install the chuck and expand it in the recess and turn the bottom with a tennon for the reverse turn.

Important: bring up the tailstock and make a center mark with the live center in the center of the bottom tennon.

Reverse the bowl and grab the tennon and finish the inside of the bowl.

Now, for Carol's lathe I made a disc with a face plate attached and trued up the disc, applied a piece of PSA foam and, using the center mark on the tennon bring up the tailstock centering the bowl on the faceplate disc with the live center on the mark previously made and finish the bottom. Light cuts are the rule here as this is only a friction hold. The remaining nub is then cut with a carving tool or chisel and sanded. If a drill press is available and having an appropriate size forstner bit, the expansion recess is easier and faster than using the parting tool.

Can you see through the mud here?

Re: locking lathe spindle - Mr. Crandall??

#7

Dave answered your question

Carole Valentine

>

Re: locking lathe spindle - Mr. Crandall??

#8

Re: Dave answered your question

JohnKJordan in East TN

>What I don't like about that solution (the one apparently devised by Jet) is the gyration needed to rotate, rest, and keep the knockout rod in contact on the back of the lathe so it doesn't fall out while the other two hands are busy with the piece. If I used the mini a lot, I think I would make myself a version the Lucas idea, perhaps adding a simple bumper at the back but higher than the lathe bed.

BTW, I'd personally be afraid of using an indexing plate for this unless it was pretty tough. A handy bench vice might work great to hold the wormwood screw while tightening, unless you use a Glaser screw chuck (my favorite).

JKJ

Re: locking lathe spindle - Mr. Crandall??

#9

Here's my solution

john lucas

>John is right. When you try to use the bed as a stop especially when you are trying to use a screw chuck, every time you relax your grip on the wood the locking bar falls to the floor.

I wouldn't trust it to an index wheel unless the pin is supported right next to the index wheel and the wheel is very strong.

You can't use the handwheel on this lathe because it's only held on by set screws and it will come unscrewed very easily.

My method uses a metal plate on top of the lathe. It's held on by 2 10/32 screws. It is short enough that it doesn't get in the way of the chuck or large faceplates. The only downside I've found is that it is possible to catch your fingers on it when installing a chuck if your being clumsy. You do have to work at it but it is possible. If I did it again I might bend the metal down and out so it sits right above the spindle and would be less likely to catch your fingers.

I know someone will ask so the knob on the lower right is the locking knob to the index wheel I added to the Jet mini.


img

Re: locking lathe spindle - Mr. Crandall??

#10

Re: Here's my solution, and next....

Carol - now in NC Nebraska

>Cool, John. I like it. And I'll use it. Thanks.

Now how about a shot of your index wheel and the knob at the lower right in use?

And some thoughts about index wheels and where to get them. Think frugal here! This is for those of you with fat wallets.

John is frugal. I know he will think frugal.

Re: locking lathe spindle - Mr. Crandall??

#11

Re: Here's my solution, and next.... *LINK*

john lucas

>Carol It's hard to beat the index head from ironfireLLC.com They are work great and are really inexpensive. All you have to do is rig up a way to hold the index pin. I haven't tried it on the Jet Mini yet but I'll bet you can just glue a block to the front of the headstock like I did on my Powermatic. Then drill holes to match the holes in the index wheel.


http://www.ironfirellc.com/shop/

Re: locking lathe spindle - Mr. Crandall??

#12

Re: Here's my solution, and next....

Carol - now in NC Nebraska

>Link looks good, John. I've bookmarked it. Thanks.

I was referring to your picture of the spindle lock and you pointed out the knob in the lower corner. I looked closely at the picture and it seems like it operates a shaft (presumably spring loaded) that goes through the headstock to pin an index wheel on the handwheel side of the spindle.

Or do I need to clean my glasses? :)

Re: locking lathe spindle - Mr. Crandall??

#13

Re: Here's my solution, and next....

john lucas

>Carol It is a knob that actuates a spring loaded shaft that drops a pin in the index wheel. It was a real pain to build and even harder to the spring tension just right to make it work every time. It was one of those, seemed like a good idea at the time things.

My other method for building and installing an index wheel on the jet mini is better and easier to build but you only end up with a 24 or so indexes. With the ironfire index wheel you get hundreds of possibilities and it's so much easier to install than anything I've come up with.