Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

Posts

DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#1

DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

charlie belden

>Josh Salesin, in Silicon Valley Woodturnes Oct. 2006 newsletter, has a great article on his DIY inexpensive (relatively speaking) vacuum kiln for drying wood.

About $350 in parts, less if you're a good scrounger / bargain hunter - 7% MC in one to three days.


DIY Vac Kiln Article in PDF format

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#2

Re: DIY Vaccum Kilns Article - 7% MC in 3 days

Cyril Griesbach

>Thanks, Charlie. An interesting aricle and an great newsletter.

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#3

Re: DIY Vaccum Kilns Article - 7% MC in 3 days

Dick Coers

>Charlie,

I'm kinda new here, but are you part of that club? Did you see the demo? I'm curious because I didn't think radiant heat transfered in a vacuum. Does he cycle the vacuum on and off so the heat will build up?

I've read quite a bit about vacuum kilns on the forestryforum and I was under the impression this wouldn't work at all. I'll post the link there and see what the gurus say. Thanks.

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#4

Re: DIY Vaccum Kilns Article - 7% MC in 3 days

JohnKJordan in East TN

>>...I didn't think radiant heat transfered in a vacuum. Does

>he cycle the vacuum on and off so the heat will build up?

Dick,

I'm interested in hearing all experiences about this.

I've also read about the heat issue in vacuum kilns. I suspect what might make this work is the "outgassing" of water vapor at reduced vapor pressure, enhanced of course by what heat can be applied radiantly or retained. Heat/pressure cycling sounds reasonable. Seems to me that like alcohol soaking, how well this works may depend largely on the thickness and porosity of the specific wood. Microwave heat might be great for a vacuum kiln but it would take a womping big microwave oven! Hey, how about vacuum microwaving alcohol-saturated pieces? :)

JKJ

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#5

Re: DIY Vacuum Kilns Article - 7% MC in 3 days

Barry Irby

>Dick, I just scanned the article. Not an expert by any stretch, but I do know that radiant energy will pass through a vacuum. That's how the heat of the sun gets to us. Ninety three million miles of vacuum and about a hundred miles of atmosphere. At the speed of light. Radiant energy is literally unimpeded by the vacuum.

As for the rest of it, your guess is as good as mine.

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#6

Re: DIY Vaccum Kilns Article - 7% MC in 3 days

Jerry Bennett

>The vacumn method works very well. I took a chair making course from Robert Hensarling in Uvalde Texas. He uses a vacumn kiln made from a huge propane tank to dry slabs of mesquite. It has a smaller tank underneath to catch the water without releasing the vacumn. Heating was accomplishes with heat strips placed between the boards. As water boils at 100 degrees or so under vacumn, the wood only has to be brought up to that. He did massive amounts at a time. He said it took about 2 weeks to do a full load. He has used this method for years. He probably would not mind your asking about it. www.mesquiterocker.com

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#7

Re: DIY Vaccum Kilns Article - 7% MC in 3 days

Dick Coers

>Here is the reply I got from Den on the Forestryforum. If I read his work correctly, he is an engineer at a vacuum kiln manufacturer.

"The heat from the bulb is not radiant but convective because of the fan. A 100W light bulb could produce enough heat to dry one board foot in 13 to 20 hours if you could get all of the heat into the wood.

He is running it as a discontinuous vac. He says in pulls the pressure down a couple times a day.

And, as mentioned in the past, water gets in the oil of the pump."

The machines that Den engineers have aluminum extrusions that go between each layer of lumber, and they pass hot water in those. That puts the heat in full contact with the wood. They have a chiller that cools a coil inside the chamber and the moisture condenses on it and is drained out. Of course the coil is stainless steel.

There was also some discussion on the forestryforum about putting a slab in a vacuum bag and submerging it in hot water. That would work well except it's one slab, the bag can not have any pin holes, how do you keep the water warm and circulated................

I was looking at all this when I had the brainstorm (maybe brain fart, LOL) about turning all the monster urban logs that my city grinds into chips, into endgrain flooring tile. My thought was that even soft maple wears forever on the end grain, and even siberian elm would have a good look on end grain, and mineral stained and spalted would be even more valuable. Just the perfect use for all those low grade logs. I asked Den about this and he told me that 1' to 1 1/2"end grain blocks would dry in a single day in his companies kilns. So if there are any venture capitalists watching......... I have to get in the shop and stop this dreaming. Gotta make some chips and break down some of the logs into vessels that I can't sell either. LOL

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#8

Re: DIY Vacuum Kilns Article - 7% MC in 3 days

Barry Irby

>This is interesting. Yet again, something I know almost nothing about. I read up a little on dragonwood a couple of years ago, but nothing of vacuum drying.

It takes a known amount of heat to convert liquid water into steam. (The latent heat of vaporization) The amount per gram or pound is known. Wonder what effect the vacuum has on that. Probably none. Probably still takes the same number of BTU or calories, just at a lower temperature.

We normally dispose of the moisture while air drying, by letting the air blow it away. In a vacuum chamber there would be very little air flow, but the vapor/steam would go Ito the pump, possible damaging it.

Wonder if some sort of desiccant could be used to soak it up? You might be able to use the desiccant and then dry it out periodically.

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#9

Re: DIY Vaccum Kilns Article - 7% MC in 3 days

charlie b

>I wasn't in the club when this article was done. I found it while putting together the new club website. Had to go through all 48 newsletters in order to do a - What's In It - for each one to hopefully save someone a 3 or 4 meg download.

Note that Josh does mainly ornamental turning so he's not dealing with big chunks of wood, nor tons of wood.

Re: BTUs to convert liquid water to gaseous water - with a vacuum pulling 28 mm of mercury I can get water to boil at room temperature - say 75 degrees.

I've used a vacuum pump that uses oil - and a not inexpensive oil at that - about $20 per quart (has a high vapor pressure while keeping the viscosity low - or high - never can remember which is which for "thinner"). Oil vacuum pumps use steel vanes and water and steel go to rust. Rusty vanes don't do their job so the oil is probably changed frequently.

If you want more details - ie have specific questions- I can pass them along to Josh and he can either use me to relay the answers or perhaps he'll participate in this forum.

Sure wish I could lay my hands on the hi-vac stuff I played with back in the early '70s - walk in vac chambers that pulled down to ten to the minus 7 microns of mercury - and had oil spray and liquid nitrogen traps to catch the last few air molecules. Surplus equiptment was sold at a penny or two on the dollar

Re: DIY Vaccum Kilns Article - 7% MC in 3 days *LINK*

#10

Easy heat -sink

Keith Newton------WebKitFormBoundaryDZmgloT+ZiYFgX

>Charlie, I suppose that you started this thread after reading Bill Hale's question for me below.

I don't claim to be an expert at vacuum kiln drying. I had only fooled around with it for a little while looking for an easy way to use the process, and I did not want to spend any money on it.

If any of you are interested in going on with this, something that came to me after my last experiment, was to heat some sand in the oven, which I would pour into a cloth bag, like a pillow slip, which would provide latent heat in close contact with the inside of any complex form, and give up that heat by conduction.

If any of you are interested in taking on the effort of trying to develop a way speed your drying process, you may want to read some suggestions to Bill that I made yesterday below.

Just keep in mind, that the hard part is to get the moisture out of the chamber, and not ruin a good pump.