Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

A question for lacquer experts

Posts

A question for lacquer experts

#1

A question for lacquer experts

Ron in Drums PA

>I finished a box with a inlaid top. I rarely if ever use lacquer, but because I was using some beautifully spalted maple, I wanted to keep the wood as white as possible.

I guess I had less than a perfect seam and in two places the lacquer sank into two tiny pinholes.

Short of removing the lacquer and starting over, how should I fill in these holes.

Re: A question for lacquer experts

#2

Re: A question for lacquer experts

Ken Oakley-ChillySt. Cloud, Fla

>If the holes are tiny you might try putting tiny dabs of lacquer on the holes with a thin artist brush and build it up. When it has dried, sand it and surrounding area smooth and level, apply a thin coat to the area and polish with 0000 steel wool or compound. Lacquer is a pretty forgiving finish. Has been my finish choice for 50 years.

Re: A question for lacquer experts

#3

Re: A question for lacquer experts

Bill Hale / The Wood Spinner

>If the holes are to big for ther lacquer fix you can use a drop of med. thick or thick CA., no accelerator as it may attack the lacquer sand after cure and do another coat of lacquer.

Good turning and be safe

Bill in CG, AZ

Re: A question for lacquer experts

#4

Re: A question for lacquer experts

Ron in Drums PA

>Thanks Ken, I was hoping I could do this.

I used Masters Spray lacquer on the piece. I also have a can Deft brush on lacquer. Both are glossy. Should I spray a puddle of lacquer on some scrap and use that or can I use the Deft?

Re: A question for lacquer experts

#5

Re: A question for lacquer experts

Ken Oakley-ChillySt. Cloud, Fla

>I am a Deft man myself and that is what I would use straight from the can. A LITTLE DAB WILL DO YA. If you remember that slogan you are old.

Re: A question for lacquer experts

#6

Re: A question for lacquer experts

Ron in Drums PA

>Brylcreem!

Thanks Ken

Re: A question for lacquer experts

#7

Re: A question for lacquer experts

Dale Cook

>I usually brush on the first 3 coats with a foam brush. These are heavy coats that I sand down for a filler type base. You can brush all the coats on and check for pin holes, sand and brush on more lacquer.I usually spray the following coats and don't sand until the end. I've switched to a different brand of spray lacquer called proven brand. This has around 88% lacquer where deft has 60 some percent.

Re: A question for lacquer experts

#8

Re: A question for lacquer experts

Ken Oakley-ChillySt. Cloud, Fla

>Wish I had something on my head to use it on------

Re: A question for lacquer experts

#9

Re: A question for lacquer experts

Mike Nelson

>Dale, does this lacquer have the fan tip?

Re: A question for lacquer experts

#10

Re: A question for lacquer experts

Dale Cook

>Hi Mike, just a regular tip but it sprays very nice.I would think you could put a different tip on this.

Re: A question for lacquer experts

#11

Re: A question for lacquer experts

Mark Kauder, Phenix City, AL

>Ron,

For the most part, you have already gotten good information.\

I try to avoid CA over lacquer. Directly to a hole in the wood, and then lacquer over is usually good.

I have never made a secret of my dislike of Deft. It has a low solids content, and a high retarder content. As a result, it will continue to shrink (get thinner) for the next few months. SO, you might fill those pin holes now and they look great now, but in a couple months you or your customer will see the pinholes again.

I would recommend the Behlen's Stringed Instrument lacquer or McFaddens Guitar Polishing Lacquer.

Mark