Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Trying to get the hang of it

Posts

Trying to get the hang of it

#1

Trying to get the hang of it

Mark in B'ham

>After asking for opinions about a month ago, I finally decided to go ahead and get a Jet Mini. Now, I'm trying to get the feel for the cutting tools. Last night I mounted a piece of practice wood and tried to shape out a small dish. I have it mounted on a glue block on the face plate and still have it between centers while I rough out the outside shape.

Here's my question, I kept getting pretty bad catches when I tried to let be bevel ride and then cut a small shaving with the gouge. I found that if I lower the angle of the cut and take a sort of scraping cut I get fewer catches. Any suggestions?

Yeah, I know, get of the computer and go watch someone else do it. I will, I will, but until then?

Re: Trying to get the hang of it

#2

Re: Trying to get the hang of it

Jim Pugh, Elyria, OH

>Mark, tell us what tool you are using and then we can offer some suggestions.

Re: Trying to get the hang of it

#3

Re: Trying to get the hang of it

john lucas

>Mark Are you in Birmingham Alabama? If so there is a very good turning club there with a lot or really good helpful people. I'll get you a name if you are.

Here is what to try. First anchor the tool on the tool rest. Then put the bevel of the tool on the wood so it isn't cutting. Now lift the handle until it starts to cut.

The reason you still get a catch if you try the above is what we call an unsupported edge. This is hard to describe in works but if you think a U shape. You have the bottom of the U on the wood. This is supported. If you now cut with the top portion of one side it is not supported and will try to pull that edge down toward the bottom, rapidly. This is a catch. Now if I rotated the U sideways and cut with same portion it won't catch because the side is supported.

As you cut down through a bowl you may have to rotate the gouge slightly so the cutting edge is supported directly below the point that it is cutting.

If you let us know what tool you are using we may be able to help you further.

Re: Trying to get the hang of it

#4

Re: Trying to get the hang of it

Mark inb'ham

>I was using a rather small gouge when I was having troubles. Actually, I started using a skew, but decided that that was too difficult.

Re: Trying to get the hang of it

#5

Alabama club

Mark inb'ham

>Thanks Steve, I already got a line on the Alabama club that meets in Birmingham. They meet on the 2nd Saturday of the month. I missed the first meeting this year, but I may try to make the Feb. one. Another poster clued me in a while back.

Re: Trying to get the hang of it

#6

Re: Trying to get the hang of it

Jake Niedling

>Mark,

Try using the gouge with the U shape of the gouge rolled over on its side to about 45 degree angle. You can roll it over to the left or the right. The basic rule is to roll it over to the same direction you want to cut. Then use what many turners call the "ABC's". Place the tool on the rest (Anchor = A), then with the tool handle down about 45 degrees below the rest rub the back of the bevel or some call it the heel ( bevel rubbing = B) and then slowly lift the back of the handle until you see small wood shavings coming off the front edge of the tool ( Cut = C). If you can maintain the cut with the bevel rubbing and anchored to the tool rest, it is very difficult to get a catch. Once you raise the tool handle up to far, then you will loose the bevel rubbing behind the cut, then a catch can occur. Hope this helps.

Jake

Re: Trying to get the hang of it

#7

I meant John.

Mark inb'ham

>I wish you could see the post you are responding to when you type. Sorry, John.

Re: Trying to get the hang of it

#8

Re: Trying to get the hang of it

Mark inb'ham

>I took me a while to get back to the shop, but I gave your suggestions a try and am doing much better. The ABC thing helped me to visualize what needed to happen.

Another thing that helped, was getting my tools sharper than they were. I was waiting for my Worksharp to get here, it was on back order. It seems to work really well for sharpening lathe tools.

Thanks all.

Re: Trying to get the hang of it

#9

Re: Trying to get the hang of it

JohnKJordan in East TN

>>I wish you could see the post you are

>responding to when you type.

Mark,

One thing you can do while posting is select the message, hit Ctrl-C to copy, click Post Response, then click in the Message box and press Ctrl-V. This dumps a copy of the message in the box that you can refer to and delete later, or leave a short portion as a "quote" to help a reader follow a thread with several branches. (I like to use the old BB ">" convention to show quoted text.)

Another method if you have enough screen space: you can keep the message displayed and open up the Response dialog in a separate window. Right-click on the Post Response link and choose "Open in a New Window", or the equivalent in your browser and OS. A big advantage of this method is it lets you review the entire thread if needed while typing. I always use this method since I use dual monitors and have plenty of screen space.

--------------------------

As for the catches, it's hard for me to make a guess without seeing what you are doing, but I used to get major catches when I tried to cut with the wings/sides of the gouge - it helped to swing the handle around until I was cutting more with the tip than the side. It also helped to "aim" the top of the flute more or less in the direction I was moving the tool. After some experience, it got easier to cut more with the sides under some conditions, for example on the outside of a bowl with the handle very low.

The scraping cut, sometimes called shear scraping if I am picturing what you are doing correctly, is great for light smoothing, but not much good for major material removal. (And it's hard on the razor-sharp cutting edge.)

JKJ