Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Wands / spindle turning

Posts

Wands / spindle turning

#1

Wands / spindle turning

MWWoodWorks

>I was wandering if I could get some information about turning small diameter spindles / wands. In another posting I saw pictures of several "Magick Wands" that John in Tenn. turned and would like to try to turn one. I turn miniatures for the most part on a Jet midi lathe. are there any tips you or anyone else could give me to make this easier. I don't have a very large supply of wood so I don't want to waste any. Also, if there are any jigs that I could build to make my turning life more simple for this? Thank you fro any instruction you may be able to offer!

Re: Wands / spindle turning

#2

Re: Wands / spindle turning

Barry Irby

>Assuming the wand apart would be about 8" long and start about 3/4" square, you need a way to grip it.

you could turn it between centers, but a spinalaid this thin is likely to buckle if you put much pressure on the ends.

You could use a chuck to hold the driven end if you have one or, you could taper the end of the work piece a bit and drive it into the taper in the shaft on the head stock. I like this method because here is no chuck or other contraption in the way, nothing to snag a knuckle on. Either way, you will want to bring the tailstock up and support the other end, at least until you get to the final shape. I have a ball bearing center and snug it up tightly for a few seconds and then back off a bit so that there is an imprint in the end of the work for the center to grip, but little or no pressure on the piece.

With care, you should be able to turn the wand part. I would turn a short tenon on the handle end, to fit into the handle. Pick a size that suits you 1/4" or 5/16" or whatever.

For the handle you can do the same thing, with a slightly larger piece of wood. Turn the handle with the butt end toward the head stock and the tailstock in place. Back off the tail stock and use a Jacobs chuck mounted in the tailstock to drill it to match the tenon you put on the wand.

In both cases, you part off after you finish sanding. This is a good place to practice your skew skills. If you get good at the parting off with the skew you will need very little hand sanding. You can also burnish on a little wax or other finish also, leaving the tenon free of finish so the glue will take.

If you drill the handle a little too deep you can use the space to add a magic element inside the handle such as a dragons scale, or the eye of a newt.

Re: Wands / spindle turning

#3

Re: Wands / spindle turning

Brian Hahn in SW Wisconsin

>I turned my first (and only) wand for Christmas. I used a single piece of wood (oak) about 11" long and 1" square. I turned it between centers with a spindle gouge. I stole the design from one of the other pictures that JohnKJordan (aka JKJ, etc.) posted last fall. (Do a search for "wand".) By happy accident, the balance point was right at the front of the "handle" section.

Re: Wands / spindle turning

#4

Re: Wands / spindle turning

MWWoodWorks

>Jacob's chuck? Don't have one of those. I have the one way 4 jaw headstock chuck with a few different sets of jaws for it but all I have for the tail stock is what came with the lathe. I never thought about tapering the end of the piece to fit into the headstock! So, it's best to turn these in two pieces? I assumed it was one piece? I guess that would add versatility to the piece turning it from two pieces. Contrasting woods and such. I have turned several pens so I have gotten ok with the skew. I have some bloodwood that would be really neat looking as a wand! Idea's are just flowing! : )

Re: Wands / spindle turning

#5

Re: Wands / spindle turning

MWWoodWorks

>That brings up another question, how does one balance the piece or is it really just eyeballing / dumb luck at the end of the day? LOL

I got the impression that you aren't going to be turning wands anymore, was it that much of a pain in the rear? How did yours turn out? (No pun intended)

Re: Wands / spindle turning

#6

what I do

JohnKJordan in East TN

>MMWW, (and anyone else interested),

I'm sure there are several good ways to proceed. I'm certainly not an expert turner but I have made several hundred wands. I can tell you my methods and some reasons why. (This is for one-piece wands)

-----> Start with a blank 3/4" to 1" square by 12" to 1" long. Most of my wands are about 10"-11" long. Straight grain is better since burl or wild grain will tend to flex more and break. Hard, tough, fine-grained wood is easier to work with but anything can be used. Small tight knots are ok but large knots, cracks, shake, and other defects can make it difficult to complete the turning. If there is some interesting figure or tight know in the wood, try to position it on the handle end rather than the spindle end. Wood should be dry since green wood will often flex too easily.

-----> Optional: Trim off some wood on the shaft end as in the photo below using the bandsaw. I make several shallow cuts in from the side then rip strips from the sides. Besides making the turning quicker and easier, the little strips of exotic woods are useful for other things (and kids love them). Don't trim off too much in either dimension since that will limit design flexibility while turning.

-----> Mark the center of each end of the blank. In hard and/or brittle woods (dogwood, bloodwood, osage orange, oak, bubinga, pink ivory, etc). I make a small hole in each end for the points of each center. Without this hole, brittle wood will split under compression from the tailstock, especially as the shaft is turned thin. When making wands in batches, the hole will simplifies mounting the next blank. Instead of using an electric drill, I keep a small gimlet stuck to the side of the lathe with a magnet. You can find gimlets at Woodcraft and elsewhere - I find them convenient for many other tasks such as starting holes for screws.

-----> Optional: Turn a short Morse taper on one end to fit the lathe (as in the photo below). Why? This will allow the blank to be jammed into the lathe spindle shaft and act as a chuck. You can also simply grab the end with a chuck but I don't like to do this for two reasons: One, the chuck is large and gets in the way when turning the end. This may mean you have to allow a little extra length in the blank for clearance, causing more problems with flexing. Two, you have to be more careful around a spinning chuck. Three, on a short mini lathe, the chuck takes up space that might keep you from turning a longer spindle.

Note: I found it very important to grip one end securely in a chuck or jam chuck. If turned entirely between centers, the shaft can flex more easily on the two pivot points on the ends. If one end is held securely in a chuck, that end cannot easily flex so the strength of the wood minimizes flexing in the entire shaft. Another reason for chucking at one end is it simplifies the final step of parting off both ends.

To turn a short morse taper, I start by measuring the exit diameter of the morse taper on my lathe by measuring the burnished line on the widest point on one of my drive centers.

Mount the blank between centers. I use a 1/2" Steb Center to drive the blank. Turn a short cylinder (about 5/8" or so) on one end with a parting tool to that exact diameter. Then I turn a slight taper on that short cylinder. The first few times, I took a second measurement from the shaft of the drive center as mentioned above, but after that I just eyeballed it. If I accidently get it too loose, I just cut it a little longer. Since I was making wands in batches (I made about 75 for the last book release), I made a little brass go-nogo gauge to make things quicker.

The taper does not have to be perfect. If the wood is soft, it will give some when pressed into the lathe spindle. (One hint, it is easier to get a tight fit on very hard wood by cutting a small relief groove in the center of the short morse taper. I can make a diagram if needed.)

-----> If using the jam chuck method, force the blank snugly into the lathe morse taper. I simply tighten up on the tailstock, then back off a tiny bit. (TOO much compression force on the blank while spinning may cause it to flex.) If using a conventional chuck,

-----> Round the blank. Since it is small diameter high speeds are OK. Use whatever sharp tool feels comfortable (small roughing gouge, spindle gouge, skew) but since the shaft is getting thin use a minimum amount of force. I start by rounding the thick handle end then the thin shaft.

-----> Turn the shaft thin before the handle. This tends to keep more strength in the better-supported end and keeps flexing to a minimum. I primarily use a 1/2" skew chisel but a gouge will also work. Razor sharp tools are a must.

-----> Support the thin shaft while turning. The most effective way (for me) is to cup the fingers of my left hand lightly around the spinning shaft to support it while holding the cutting tool entirely with my right. The left hand travels with the tool to support the shaft always right behind the cut.

This method requires a bit of practice. Some things I do: rest my left arm or elbow on the top of the headstock housing. Grip the tool close to the cutting end with my right hand and support the handle if necessar by pressing it under the right forearm. Use my left thumb as needed to steady and push the cutting tool as needed - this is especially handy when using a skew on grooves or cutting tricky curves.

I read this good advice in one of Raffan's books (I think): if your fingers get hot from the friction, you are using too much force! Back off, slow down, sharpen the tool.

Note: there is come controversy about the safety of putting your hands in contact with spinning wood. I consider this reasonably safe since unlike a larger shaft or bowl, the very thin shaft will easily break. The biggest hazard might be wearing loosely fitting sleeves with the left arm draped over the work, especially when using a chuck. Another reason not to use a chuck.

-----> If the thin shaft begins to flex and vibrate, back off and change something. Things I try: loosen or tighten the tailstock. Speed up or slow down the lathe. Sharpen the tool. Try a different tool. Cut in a different direction.

Occassionally when planing with the skew chisel I run into a situtation where out-of-roundness, say from irregular hardness in the figure, can cause the skew to bounce on the bevel instead of cut smoothly. This is bad on a thin spindle since unlike a heavier piece, each bounce flexes the shaft regardless of how firmly you support the tool. In this case, the thing to do is to cut with the point at the heel of the skew instead of part way up the cutting edge as normal. This peels back the rough wood and lets the bevel follow smoothly behind.

Occasionally you will have a disaster (small catch or something) that causes the entire shaft to bend like a bow. This is more likely with soft or flexible wood, especially if the wood is not quite dry or the grain is not straight. If this happens, I stop the lathe and bend the shaft back into place. Sometimes, I'll just smack the shaft lightly near the center with the handle of the tool while the lathe is spinning. It may take several tries, but eventually I hit exactly the right spot and the shaft snaps into true again.

-----> After thinning the shaft most of the way, I rough out the handle, then finish turn the shaft, then finish turn the handle. I shape the very end of the handle last, leaving 1/4" or so to drive the wand while finishing.

-----> Sand and apply finish. I like to use beeswax for a soft finish, escecially on cedar. Mylands friction polish is great for a high gloss and very quick.

-----> Part off the tip end with a skew chisel while continuing supporting the shaft lightly with the left hand. The skew will make a far cleaner cut than a parting tool, leaving the end ready for hand finishing off the lathe. Back off the tailstock a bit if there is still pressure.

-----> While continuing to support the shaft with my left hand, I reach under with the skew and part off the handle end. Sand and finish each end by hand as needed.

As for design, it's wide open! I tend to try something new and wild on whim, repeating designs I find pleasing. I sometimes use a wire to burn accents in groves - that can look good not only on light woods but on darker wood such as walnut. I've done some multi-axis that were nice. This summer I started making some with distressed handles which were very popular - I scratch the handle with a sharp tool, dig grooves with a small gouge, smack dents into the side, use a coarse wire brush to dig into soft grain, etc., then sand lightly

before finishing.

Two-piece wands, say with a dark handle and lighter shaft, are a bit easier to turn but take a little longer. I've made a few with a contrasting light ring between the handle and shaft of a darker wood.

If the wand is for a specific person, I try to make the handle fit the person. I made up a bunch of different styles of handles on short scrap wood to let people try them for fit.

That's all I can think of at the moment. Some day I hope to take photos and write up a short article with these steps. I have lots of photos of past wands if anyone wants to see them. Most have been posted here before and are in the archives, but I noticed recently that some of the archived photo links have been corrupted.

JKJ


img

Re: Wands / spindle turning

#7

Re: what I do

MWWoodWorks

>Wow! That's a pretty detailed discription! Thank you very much! JKJ, do you even try to balance the wands or do you just eyeball it and hope for the best? What kind of wood is that in the picture? Speaking of pictures, I would love to see more of the pictures that you mentioned! I would like to get an idea of some good shapes to try! I can't wait to try one! :)

Re: Wands / spindle turning

#8

Re: Wands / spindle turning

Doug Turner

>One of the things you need to keep in mind is safety and potential product laiability. I turn my magic wands with a knob on the end so that if anyone gets accidentaly poked in the eye the end is not sharp. I also avoid cocobolo which causes severe allergic reactions in some people.

I use a variety of domestic wood and a variety of designs trying to make each wand unique. Good sources of wood are old pallets, broken furniture, thrift shops, recycle centers, cabinet shop scrap bins etc.

Re: Wands / spindle turning

#9

Re: Wands / spindle turning

MWWoodWorks

>As this IS the age of suing, I will take that advice to heart! LOL Good ideas about the places to find wood! I am finding that I cannot afford the wood for this little hobby of mine! LOL I purely expect to start glueing together pieces of cardbord or something to have something to turn! (Just kidding! Boy, that would probably be bad! LOL) I thnk that is why I am still turning miniautures! Pen blanks aren't that bad and I can get sevearl pieces from one blank! he he If I mess up a piece I'm only out a buck or so! :) Still trying to figure out what to do with my scrap pieces! LOL perhaps I should start doing segmented mini's?! HA

Re: Wands / spindle turning

#10

Re: Wands / spindle turning

Brian Hahn in SW Wisconsin

>Actually, it was quite easy to make the wand. I added some texturing and color to the handle that really looked good. I made the wand as a Christmas gift for my sister who is a Harry Potter fan. Both she and her husband loved it. But my turning interests lie elsewhere.

Re: Wands / spindle turning

#11

Re: Wands / spindle turning

Barry Irby

>A Jacobs chuck is the type of chuck on a drill or drill press. You can get them mounted on a Morse taper that will slip into your tail stock or head stock. You don't really need one for this. If you turn the handle with the butt end toward the headstock, you will have the center marked by the tail stock, or you can use a sharp skew to mark the center for you. Then you can back the tailstock out of the way and drill the end of the handle with a drill bit gripped in a pair of pliers. Vice grips work well. Or, you can make a handle like the ones for a wand, drill the hole in it and use CA or Epoxy to glue the shaft of the drill bit into the handle. Then you have a tool to drill future handles. (If you use a fairly long drill bit you can use it to drill a hole into your bowls to set the depth of the bowl.)

You can use a wrench that matches the size of the drill bit as a gauge to sett he size of the tenon. Or you can get really fancy ans sharpen one side of the wrench to make a tenon cutter. (there were pictures of such a thing here a week or two ago.)

Re: Wands / spindle turning

#12

PS, About that Morse taper

Barry Irby

>I actually bought a gauge to help me make the Morse taper on the blank. It is shaped like an "E" The upper space in the E is the small end of the taper and the lower sot is the larger end. The spine of the E is the length. Works well, but it's too much trouble.

I have a belt sander mounted upside down. Its a poor man's general purpose edge sander. I just cut my blanks square and some times pater them a bit on the bandsaw by eye and grind them round on the sander. They are pretty crude but they work. Once I get the size in my head, I just grind them into submission. Takes seconds, much faster than mounting them between centers and turning a taper on them. (BTDT)

I have been thinking of making a little slider to put in the slot on the band saw so that I could just hold them on the slider and cut a taper on them quickly. It would work on the bandsaw or table saw and it would be quick. Probably could knock the corners off on the sander, but it may not be necessary.

Re: Wands / spindle turning

#13

Re: PS, About that Morse taper

Bob Macgregor

>I wonder how hard it would be to machine a giant Morse taper pencil sharpener to knock these off really fast and accurately?

Re: Wands / spindle turning

#14

LOL mental image of that is great! 

MWWoodWorks

>

Re: Wands / spindle turning

#15

Re: what I do

JohnKJordan in East TN

>MMWW,

- I don't try to balance anything. I never once even thought about it. They always seem to come out OK. Of course, they are pretty small pieces of wood, not heavy like an axe or something.

- The piece of wood in the picture is Cocobolo, one of my favorite turning woods. It turns so smoothly I rarely need coarser than 400 grit sandpaper. I like it for wands, tops, boxes, pens - almost everything. Some people (like me) have allergic reactions to the dust, but once the piece is finished, it is as benign as maple, walnut, or anything else. It might be a problem if you chewed through the finish.

- I'll get some pictures together and post them in another thread, perhaps later tonight.

One great thing about wands is you can make them from pieces of wood no one else wants, or buy small lengths of domestic or exotic boards in 4/4 thickness - wood you wouldn't normally use for turning and a LOT cheaper than thick bowl stock.

JKJ

Re: Wands / spindle turning

#16

Re: PS, About that Morse taper

JohnKJordan in East TN

>>I wonder how hard it would be to machine a

>giant Morse taper pencil sharpener to knock

>these off really fast and accurately?

I thought about that and started to make one once. It could be similar to the tenon cutters sold to rustic furniture makers. The biggest problem, as I see it, would be to align the cutter somehow so the taper would be exactly down the long axis of the blank. If it's off a bit for rustic furniture, it won't matter much. A little fixture could take care of this.

But as for the time it takes to do it with a parting tool between centers, after a few it only takes about 30 seconds. I would make up 10 or 20 blanks at one time, cutting the taper on one lathe and testing the fit on the second lathe behind me.

JKJ

Re: Wands / spindle turning

#17

Re: what I do

Mark Williamson

>I have turned Cocobolo! I love it!! Made me sneeze a few times but nothing too bad! I still haven't gotten to the point where I can identify woods very easily. Cocobolo is one of my favorite woods to turn! I bought a grab box from woodcraft a year or so ago just to learn different exotics and ended up with a box with about 90% cocobolo and the rest was lacewood. A couple of months later I bought another box and it was mostly lacewood and the rest cocobolo! LOL

Re: Wands / spindle turning

#18

Re: what I do

JohnKJordan in East TN

>>...90% cocobolo and the rest was lacewood.

Yikes! I bought one of those grab boxes and got no cocobolo or lacewood, a couple of useful pieces of some hardwood I couldn't identify, and the rest some worthless light weight wood I couldn't identify. I didn't feel like I got a good deal. Maybe I should try again...

JKJ

Re: Wands / spindle turning

#19

Re: what I do

Mark Williamson

>I have gotten mostly thins with a big chunk of unknown in them. I stopped buying them because I just couldn't afford to pay all that money for more lacewood thins, and paduak! Lots of paduak! but mostly thin pieces. I did get a couple of really awesome chunks of ebony one time though! I have gotten some nice looking stuff but unable to identify. I figured I was better off ordering pen blanks and turning the mini's from them. At least then I would know what they were and I knew I was getting useful sized pieces! LOL

Re: Wands / spindle turning

#20

Re: Wands / spindle turning

Carol in Illinois

>Hi, all.

I've made and given away over 100 magic wands. I turn them entirely between centers, using at least two kinds of woods. I turn on a Rikon mini, and my wands range from about 9 inches to a tad more than 13. I've never needed a steady rest... occasionally I need to steady a longer wand with one hand, but only for the 13-inchers. I've never lost a wand. Here's my process:

1. Select two complimentary woods for the wands. They must play nicely together. I often use pen blanks for the two woods, and this is how I started out. I quickly moved to include longer pieces than pen blanks, though.

2. Drill a "mortise" about an inch deep into the piece that will be the handle or haft of the wand. Set it aside.

3. Mount the piece that will be the wand "tip" or "blade" between centers and turn about a 3/4" "tenon" at the end that will fit into the haft. Test the size of the tenon using dial calipers sized to the solid end of the drill bit that made the mortise. Until you're confident of your sizing skills, make the tenon a tad "fat" - it can be sanded to a good fit off the lathe if necessary. Be sure the tenon shoulder is square to the tenon and flat. (It's possible to use a concave or convex tenon shoulder, but that's more complicated a "join".) I do not round the entire blank at this point.

4. Drop a gemstone with known magical qualities into the bottom of the mortise drilled in the haft. The gemstones and woods should want to be together - they should "call" to each other, for a wand that is not contradictory or unpredictable. (Hey, if you're gonna turn wands, you might as well make a science of it, eh?) DRY FIT the joint to make sure the tenon will not bottom out against the gemstone. Adjust as needed.

5. With a good "dry fit", glue the joint. (I use Titebond.) You can fatten a loose tenon using glue and a bit of paper toweling, and you can sand a too-tight fit so it's just right.

6. If you feel queasy, or if the tenon is shorter than 3/4", wait for the glue to dry. After my 50th wand or so, I found that with a good fit, I didn't have to wait much more than ten minutes... and truth to be told, sometimes I didn't wait that long!

7. Mount the entire wand length on the lathe and turn to a pleasing shape, respecting the grain and nature of the wood. I turn with the haft toward the headstock and the tip toward the tailstock. Leave a good chunk at both ends so that the wand is well-secured as you turn.

8. Turn the handle first, as this will be the thickest part and will continue to be robust when you turn the daintier tip end. Turn the tip end next. I leave the very ends until most of the sanding is finished, then turn the finishing touches nearly to parting and sand those. (I got bolder with this as I got experience.)

9. Apply finish while the wand is still on the lathe.

10. I "part off" the stubs at each end with my scroll saw. You have to have a good grip on the wands at each end, because otherwise they will roll on you - and that will hurt! Then I sand and finish both ends.

11. I have write-ups of each individual wand describing the "known" magical characteristics of the woods and gemstones used in that particular wand. I created these after hours of (ongoing) research into magical lore, herbal lore, and wood and gemstone characteristics.

Remember: the wand chooses the wizard!

I'm attaching a link to some pics of wands... I have lots others... somewhere around here (searching through multiple USB drives, hard drives, etc...).

It's not a big step from wands to pens, as it turns out, but it took me forever to take that leap. Wands are freeform, whereas pens are exacting and unforgiving beasts! Grrrrr! I learned turning starting on wands, and have only begun to branch out to bowls and boxes in the past three months. Pens are even more recent - I have only about a month or so into those. Fun! Much more learning ahead.

Carol


img

Re: Wands / spindle turning

#21

Re: Wands / spindle turning *LINK*

Carol in Illinois

>Hi, all.

I've made and given away over 100 magic wands. I turn them entirely between centers, using at least two kinds of woods. I turn on a Rikon mini, and my wands range from about 9 inches to a tad more than 13. I've never needed a steady rest... occasionally I need to steady a longer wand with one hand, but only for the 13-inchers. I've never lost a wand. Here's my process:

1. Select two complimentary woods for the wands. They must play nicely together. I often use pen blanks for the two woods, and this is how I started out. I quickly moved to include longer pieces than pen blanks, though.

2. Drill a "mortise" about an inch deep into the piece that will be the handle or haft of the wand. Set it aside.

3. Mount the piece that will be the wand "tip" or "blade" between centers and turn about a 3/4" "tenon" at the end that will fit into the haft. Test the size of the tenon using dial calipers sized to the solid end of the drill bit that made the mortise. Until you're confident of your sizing skills, make the tenon a tad "fat" - it can be sanded to a good fit off the lathe if necessary. Be sure the tenon shoulder is square to the tenon and flat. (It's possible to use a concave or convex tenon shoulder, but that's more complicated a "join".) I do not round the entire blank at this point.

4. Drop a gemstone with known magical qualities into the bottom of the mortise drilled in the haft. The gemstones and woods should want to be together - they should "call" to each other, for a wand that is not contradictory or unpredictable. (Hey, if you're gonna turn wands, you might as well make a science of it, eh?) DRY FIT the joint to make sure the tenon will not bottom out against the gemstone. Adjust as needed.

5. With a good "dry fit", glue the joint. (I use Titebond.) You can fatten a loose tenon using glue and a bit of paper toweling, and you can sand a too-tight fit so it's just right.

6. If you feel queasy, or if the tenon is shorter than 3/4", wait for the glue to dry. After my 50th wand or so, I found that with a good fit, I didn't have to wait much more than ten minutes... and truth to be told, sometimes I didn't wait that long!

7. Mount the entire wand length on the lathe and turn to a pleasing shape, respecting the grain and nature of the wood. I turn with the haft toward the headstock and the tip toward the tailstock. Leave a good chunk at both ends so that the wand is well-secured as you turn.

8. Turn the handle first, as this will be the thickest part and will continue to be robust when you turn the daintier tip end. Turn the tip end next. I leave the very ends until most of the sanding is finished, then turn the finishing touches nearly to parting and sand those. (I got bolder with this as I got experience.)

9. Apply finish while the wand is still on the lathe.

10. I "part off" the stubs at each end with my scroll saw. You have to have a good grip on the wands at each end, because otherwise they will roll on you - and that will hurt! Then I sand and finish both ends.

11. I have write-ups of each individual wand describing the "known" magical characteristics of the woods and gemstones used in that particular wand. I created these after hours of (ongoing) research into magical lore, herbal lore, and wood and gemstone characteristics.

I'm attaching a link to some pics of wands... I have lots others... somewhere around here (searching through multiple USB drives, hard drives, etc...)

Not a big step from wands to pens, but it took me forever to take that leap. Wands are freeform, and pens are exacting!


http://osterwood.homestead.com/wandpics.html

Re: Wands / spindle turning

#22

Re: Wands / spindle turning

Mark Williamson

>It's interesting hearing to different ways people make these! I still am amazed that there are so many people turning them? I didn't realize that there was such a market for them? Assuming that all that are turning more than 1 or 2 are actually turning them to sell. I hope this sin't a bad question to ask but I am going to try anyways. How much do these go for? I imagine that the price ranges due to the materials used obviously. The gemstone in each being a nice touch and would probably demand more at the table than me just turning an oak wand! LOL I have never see any wands for sale? I saw that JKJ was selling them at Harry Potter openings but if I am not mistaken, I thought Ole Harry Potter cast his last spell so to speak? LOL

What are the opinions on what to use for a finish? I have not gotten the knack of the CA finish yet! One day I will get it though! LOL Is there something camparable in look and wear to CA but easier to apply? (Or I am in La La Land? LOL)

Re: Wands / spindle turning

#23

Long Multi Axis Wands *LINK*

Jerry Hall

>All great advice below. Here is another "twist" on it. I have been turning bunches of Multi-Axis wands. See link below.

I have been able to do longer ones and pretty thin up to 17" long by using two jaws of a long nose chuck with the blank starting out as far back as possible to provide maximum support till I get around to the handle end. The manzanita one in the link is 17" long, and the manzanita is brittle. It helped to turn it green.

I leave about an inch or so of the tip end undone till the end to provide some mass at the end to change axis, and to further stabilize it. Then I do the final axis change at the tip. Because of the wild vibrations at this point I just saw off the ends and quickly clean up the ends with a sharp knife or skew.

I sand thru all the grits before each change of axis. I finish with Watco, or just lacquer sealer, and often buff as well.


Wiggly Wands

Re: Wands / spindle turning

#24

Re: Wands / spindle turning *LINK*

JohnKJordan in East TN

>>How much do these go for?

I don't usually sell anything, so at first I had no idea about pricing. I showed my first few around and people immediately started asking if they could buy one. When I said I didn't know what they were worth, someone offered $25. $25 for a stick?

When I set up in front of the bookstore I priced finished wands from $15 to $40. I was surprised at how fast these were sold. (I had some priced much higher that I didn't really want to sell!)

The price I used for each was based on the cost of the wood (free for many locals, expensive for exotics), the amount of time in it, and how elegant I judged the result! Those I turned on site were cheaper since I could not put as much time into them. (I had many people waiting.)

I haven't checked prices or availablity elsewhere, but while I was turning one on site for a person, I heard her tell another that if there was not time to get a second one made they wound get one from some web site (I didn't catch the name), although they were more expensive and not as nice. Mr Google may have some insight.

I found the simplest 1-piece designs sold just as well as the two-piece. I never used gemstones, inlays, or whatever.

>I thought Ole Harry Potter cast his

>last spell so to speak? LOL

I think Harry Potter books and fans will be around for a long. The last book was released this past summer, but there are still several movies in the works. I think one could cast a killer spell setting up a lathe in the lobby of a large theater on opening day (as an attention-getter) and having a bunch of wands made for sale.

For someone who wants to make some money, please steal my idea for a Custom Wand web site: let the customer pick from a bunch of handle and shaft designs, length and diameter, wood, and finish. You could even provide a means for people to email or upload sketches of their own dream wood. Charge way extra for carving, bone rings, gemstones, inlaid turquoise, whatever. Post a photo of the result and if they change their mind, put it in the Available list. When I made wands specifically for a person while they watched, I always let them help "design" the wand - this way they went away with something far more personal than one purchased off the shelf.

I ran into a clan of fans who go to conventions every year, such as the one below. They were DESPERATE to get quality wands for their next convention. I don't follow the trends, but if this is anything like SciFi these conventions are a really big deal with perhaps thousands of potential customers.

The customers are not all kids. Some bought them for their kids, but mostly adults bought them for themselves and each other, 20-something couples got two, many older teenagers had to have one, soldl some for wives for Christmas, etc.

JKJ


http://www.worldfantasy.org/

Re: Wands / spindle turning

#25

Re: Long Multi Axis Wands

Carol in Illinois

>Really nice wands, Jerry. I especially liked the picture of you catching some ZZZzzz's tho!

Carol