Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Need to make some REALLY small thickness calipers.

Posts

Need to make some REALLY small thickness calipers.

#1

Need to make some REALLY small thickness calipers.

MWWoodWorks

>Hello all! I just recently found WC and thus far am lovin' it! I have learned much all ready! I turn mostly 1/12 scale and smaller miniatures as well as pens. I have a question that some of you guys might be able to help me with. I have to make the majority of my tools due to them having to be so small. Most of my pieces are less than 1 inch in height and 3/4 inch in diameter. I am able to hollow my pieces quite well with the plethera of tools that I have fashioned from various materials. However, I would like to be able to actually measure the wall thickness of the vases, hollow forms, etc. Keeping in mind that the openings are usually between 1/8 inch and 1/2 inch. I am guessing that the wall thickness is ranging from around 1/16in. to around 1/8in.

Any ideas as to how I can make something relatively simple to measure this? All idea's would be helpful. Didn't know if there was some old tricks of the trade or something. I have seen the large sets of curved calipers but I would need something MUCH smaller than even the smallest set that I have seen.

Re: Need to make some REALLY small thickness calipers.

#2

Re: Need to make some REALLY small thickness calip

john lucas

>I would use the same method I use when hollowing christmas ornaments. I make various C shaped gauges out of stiff wire. Then adjust the gap until it is a known dimension such as 1/2" or 3/4". Put the wire inside and then measure the gap outside with a ruler. You need to keep the gap perpendicular to the wall where you are measuring for accurate measurements.

I usually make the gap in the C offcenter so that I can turn the tool over to measure areas that are hard to get to. You can bend it just about any shape as long as you know the gap and can get the imaginary line between the point perpendicular to the side.

If that's not clear I will shoot some photos tonight.

Re: Need to make some REALLY small thickness calipers.

#3

Dick Hines

Re: Need to make some REALLY small thickness calip

Dick Hines

>Are you still comming to the turning meeting next Thursday? If so I will bring the tool I made out of coat hanger. Very simple to make.

Re: Need to make some REALLY small thickness calipers.

#4

I'd do it the same way...

Brian Hahn in SW Wisconsin

>... except the wire is a capital "D" shape with a gap at the bottom of the "D" so there is a long straight leg with a short right angle arm and the opposing side has the long curve. Be sure to round over the ends of the wire.

Re: Need to make some REALLY small thickness calipers.

#5

Small Calipers

Ron in Drums PA

>I make them out of clothes hangers

You can make them any size you need


Re: Need to make some REALLY small thickness calipers.

#6

Dick Hines

Re: Need to make some REALLY small thickness calip

Dick Hines

>Iguess I don't have to bring them to the meeting. Because I use the same ones Ron does.

Re: Need to make some REALLY small thickness calipers.

#7

Re: Need to make some REALLY small thickness calip

MWWoodWorks

>Ever ask one of those questions that once you get a answer, you feel as though you should slap yourself on the foreheaad and the only word that will come to mind is , "Duh!"

Who knew it could be so simple! LOL I was trying to make it too complicated I think! That all makes perfect since!

D. Hines - Yes I am still going to the meeting next thursday. However, I beg you not to tell everyone... "Hey, that's the guy that couldn't figure out the coat hanger thing! He he he"

I am very excited about going!

Re: Need to make some REALLY small thickness calipers.

#8

Dick Hines

Re: Need to make some REALLY small thickness calip

Dick Hines

>KISS,is always the best way.

Re: Need to make some REALLY small thickness calipers.

#9

Re: For the scale pieces you are .....

JamieD

>.....dealing with you could make the C/D shaped calipers out of paper clips as I did years ago during my "miniature period."

Re: Need to make some REALLY small thickness calipers.

#10

Re: Small Calipers

Allen Neighbors

>How do you use those, Ron?

Re: Need to make some REALLY small thickness calipers.

#11

Re: Need to make some REALLY small thickness calip

Allen Neighbors

>Now you're trying to make me feel stupid... I still don't see how the work...

Re: Need to make some REALLY small thickness calipers.

#12

Re: Change 'the' to 'they'

Allen Neighbors

>

Re: Need to make some REALLY small thickness calipers.

#13

Re: Small Calipers

Ron in Drums PA

>When the long sides are parallel you can see the thickness by looking at the gap


img

Re: Need to make some REALLY small thickness calipers.

#14

Re: Small Calipers

Allen Neighbors

>Pic didn't show up, but okay, I get it now. But tell me, when you're working with thicknesses as small as 1/16th of an inch, doesn't just 'eyeballing' the sides parallel leave a little too much margin for error? What I'm saying may be based on my own experience with my shaking hands, though. So it may be easier for others to be more accurate with this device. Understand that I don't have a better solution... Just wondering......

Re: Need to make some REALLY small thickness calipers.

#15

Re: Allen- these "feeler" type calipers...

Jamie Donaldson

>...are more for "ballpark" type measurements- they don't do 1/16" very accurately! :-O

Re: Need to make some REALLY small thickness calipers.

#16

Re: Need to make some REALLY small thickness calip

Juergen

>This is a picture of the calipers that J Paul Fennell developed for his thin walled and pierced turnings. I made one of these from some spare part and it work very well. It should be easy to scale it down to meet your needs.


img

Re: Need to make some REALLY small thickness calipers.

#17

Nice!

mwwoodworks

>I really like that design! Seems easy enough to make and shouldn't have much of a problem scaling down! Very cool!

Thank you everyone for your insight, definatly very helpful!