Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Hunter tool rim cutting

Posts

Hunter tool rim cutting

#1

Hunter tool rim cutting

john lucas

>I was working on my article on using the hunter tool yesterday and thought I might give you a little preview.

There are 4 shots showing how to use the tool for cutting and undercut rim and a bowl with lip.

I turn most of the bowl shape with a bowl gouge because it's quicker. I save the Hunter tool for what it's best at. Clean final cuts and doing odd shaped pieces like undercut rims and bowls with lips too steep for a bowl gouge.

This shot is showing the angle of the tool as it cuts up toward the rim. Notice the bevel is rubbing and the tool is tilted only slightly beyond vertical.


img

Re: Hunter tool rim cutting

#2

Re: Hunter tool rim cutting

john lucas

>As the tool approaches the rim I rotate it so the cutter is facing up more. In this position it becomes more of a shear scraper and your not rubbing the bevel. I change it from cutting to scraping as I go around the corner and head up to the lip.

You can even cut backwards from the rim to the bottom in this position but you have to be careful because you can get a catch as it reaches the area where the bowl becomes more vertical. You have to try a cut each way to see which one gives you the cleanest cut.


img

Re: Hunter tool rim cutting

#3

Cutting the under outside rim

john lucas

>This is done the same way I cut the inside but in reverse. I shear cut the outside with the bevel rubbing and then rotate the cutter so it facing more up and becomes a shear scraping tool. I never get it past about 35 to 45 degrees. If you get the cutter flat it will catch.

You can see how steep I run the cutter. This was taken from the top. You don't have to go that steep until you bet to this point. It cuts slower when it's this steep so you have more control as you get into that tricky area.


img

Re: Hunter tool rim cutting

#4

Re: Cutting the under outside rim

john lucas

>Then as you get to the underside of the U rotate the cutter so it's shear scraping and gently pull it out toward the rim. you'll notice the bevel isn't rubbing so the only control is you. Take it lightly. You should probably stop and measure at this point but I did the whole bowl with my fingers and missed a little on this lip. Consequently it's a little off but looked great until I cut the bowl in half. I like the slightly thicker edge but wish it wasn't quite so thin at the joint of the two outside beads.


img

Re: Hunter tool rim cutting

#5

never throw anything away

john lucas

>What do you do when you've cut both sides off of a bowl? You go back to the table saw and cut them more accurately and then glue them back together. I have plans for this but it's going to have to wait awhile. I'll post it when I get it done.


img

Re: Hunter tool rim cutting

#6

Re: Hunter tool rim cutting

Barry Turner

>I got a Hunter #4 for Christmas. I hadn't tried it until yesterday afternoon. I only tried a couple of cuts with it, as I was doing something else (hollowing a bowl), and just remembered that I ought to try the Hunter. I made a couple of cuts with it. The cuts were very smooth, but also very slow. I returned to my bowl gouge to finish up the hollowing, as it seemed faster and easier. I won't render up an opinion on the Hunter just yet, as I understand there is a learning curve and it wouldn't be fair without spending more time with the tool.

Re: Hunter tool rim cutting

#7

Re: Hunter tool rim cutting

john lucas

>Barry one thing that we are learning is that you need to run the lathe faster. It helps get a smooth cut. I think the bowl gouge cuts faster because you have more edge going into the work. The Hunter tool is like cutting with just the tip of the bowl gouge.

I appreciate all the questions because they force me to look at the tool more closely and figure out how and why it is different than the tools we use. No one tool is good for everything and the Hunter tools are not different.

Re: Hunter tool rim cutting

#8

Re: Hunter tool rim cutting

Norm Smith

>John, Great information. I like the Hunter Tools and use them quite often and am almost over the learning curb. Congratulations on your article in Woodturners Design. I am looking forward to seeing more articles from you.

Norm

Re: Hunter tool rim cutting

#9

Mike Stafford

Re: Hunter tool rim cutting

Mike Stafford

>Barry, I think of the Hunter Tool as finishing tool. I use it almost exclusively for finish cuts and light shaping. If I am removing bulk I use a gouge to do so. Then I can refine the shape and get it nice and smooth with the Hunter.

I turned a few boxes with the wood mounted in the faceplate orientation and hogged out the interiors with a bowl gouge. I did the final smoothing with the Hunter and achieved good results.

Like John said, I found out that I had to use them at higher RPMs and then find the sweet spot/correct cutting angle.