Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Homebuilt lathe

Posts

Homebuilt lathe

#1

Homebuilt lathe

Todd O. Cronkhite Maine Native, Presently Away

>Hey guys, I posted some pics of my homebuilt lathe over on the Handtools side and thought you'all might like to see it as well. It's certainly no super-duper, nor high dollar machine, but it works well and I'm pleased with it.

T.O.

Re: Homebuilt lathe

#2

Re: Homebuilt lathe

Lan Brady

>Todd,

Very nice. Good job.

Lan

Re: Homebuilt lathe

#3

Now Todd...

Steven Kubien

>...I was wondering when we might see around these parts. Don't do it man. You've got too much time invested in your neander ways to get sucked into this vortex. Oh sure, you just want to make a few chisel handles and knobs for planes right? That's what I had said and now my planes aren't speaking to me (because I am not speaking to them).

Nice to hear from you.

Steve Kubien

Re: Homebuilt lathe

#4

Re: Homebuilt lathe

Bart Rhoads

>I had built one of these when the plans first came out in Wood magazine a bunch of years ago. I used it until 1999 when I stepped up to my General and I gave the old one to a Dr who used it for a couple of years until he purchased a Powermatic. He gave it to his brother-in-law who used it until he bought a new lathe and the last I heard it was still running and being used up in Texarkana.

I did some revisions to mine. I installed 2 pieces of 3"x 3/8" flat bar on the ways. This made it quite a bit smoother. I also changed the clamping system on the tail stock so it clamped on the steel bars instead of under the wooden ways. Other than that, thats all I changed and I was able to turn just about anything I wanted. I worked at a chemical plant in maintenance so I was able to make the shafting and tailstock quill with a morse taper myself in the machine shop. So I hope yours works as well and last as long as mine did.

Bart

Re: Homebuilt lathe

#5

Steven Antonucci

Shouldn't it be treadle driven :-)

steve antonucci

>all of you hand tool guys will be assimilated to the "main board" :-)

Steven

Re: Homebuilt lathe

#6

Re: Now Todd...

Todd O. Cronkhite Maine Native, Presently Away

>Steven, I wondered where you had gotten off to to. ;~)

Actually, I used to do a lot of turning, tho nothing like the folks over here, but got away from it when I strted finding planes at the flea markets. The lathe got pushed aside, then it went into storage for 3 years, and since I retired 5 years ago it's been used as a horizontal surface ever since. I just dug it out the other day and filled in the hole where it was so it can't get buried again.

Yeah, I need to turn chisel handles, drawknife handles, knobs. These alone should keep me "in the spin" for quite some time.

T.O.

Re: Homebuilt lathe

#7

Re: Homebuilt lathe

Todd O. Cronkhite Maine Native, Presently Away

>Yeah Bart, after I built mine I said to kyself that I should of put some flat bars on the rails to make sliding the toolrest and tailstock easier. Fiqured I'd do it sooner or later, but I haven't. After I dug it out the other day I said to myself, "man I should put some flat bars on these ways" I know work at a place where getting the iron is a snap, so I just might get around to it yet.

T.O.

Re: Homebuilt lathe

#8

Re: Shouldn't it be treadle driven :-)

Todd O. Cronkhite Maine Native, Presently Away

>Trust me Steve, I considered doing just that many many times, but then figured that I'd just build a separate treadle lathe instead. Can't have to many lathes can you?

T.O.