Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Turning bootstrapping: is this par for the course?

Posts

Turning bootstrapping: is this par for the course?

#1

Turning bootstrapping: is this par for the course?

wilbur

>Is this typical for someone getting started?

I've been trying some woodturning here and there, and decided to make bottle stoppers for Christmas gifts for some coworkers. I did some practice runs on scrap, and I realized that the chuck jaws I had were not ideal for this job, so I ordered some new jaws for my chuck. I was also using some old turning tools that I got with my old lathe, and I quickly decided that were not going to work -- they were carbon steel turning tools, and I had been practicing on 2x4 material, but I was losing the edge just from the friction when turning harder woods. I considered making bottle stoppers out of 2x4 material, then thought better of it and bought some turning tools from Doug Thompson (1-1/4" and 1/2" skews, 3/8" spindle gouge, 1/2" V-groove bowl gouge, and 1" scraper). They come unhandled. So I needed to make some handles. I looked up info on making handles, and found that I would need a 1" ferrule. Made a trip to the local plumbing supply house for some 1" brass pipe. I wanted to use some white oak I had for the handles, which I found that the aforementioned carbon steel tools weren't going to do well with. Had an interesting experience making a handle with an unhandled 1-1/4" skew chisel. I found that I needed to drill a 5/8" hole for the skew chisel, but didn't have a 5/8" bit. Quick trip to the Borg. Finally got a handle made for the skew chisel, put it together, and used it to make a handle for the 3/8" spindle gouge. Having a handle on the skew makes things much easier.

Now I can finally make some bottle stoppers. Whew!

Re: Turning bootstrapping: is this par for the course?

#2

Re: Turning bootstrapping: is this par for the cou

eliot d

>Somethings not right. It's not this hard. There's nothing wrong with oak handles, and it doesn't matter whether or not the tool you're putting in it is carbon steel or not. There's no reason to drill a 5/8 " hole to make a tool handle for a skew. You should not be dulling your tools -- carbon steel or otherwise -- from "friction". My guess is that your tools are not nearly sharp enough. How are you sharpening them? A skew, especially, has to be razor sharp. I mean sharp enough to shave with. Are you scraping, or cutting, the wood? I remember my very first turning experience. I tried using a skew because I had watched a Richard Raffan video. I had no idea what sharp meant, so when I tried to make a cut, nothing happened! I mean nothing! The skew just wouldn't cut. It wasn't near sharp enough. How is a newbie to know what "sharp" means , if he hasn't ever seen or tried to use a really sharp tool? My advice is to find and join a turning club in your area. You will save years of trial and error. Good luck.

Re: Turning bootstrapping: is this par for the course?

#3

Re: Turning bootstrapping: is this par for the cou

Bill Hale / The Wood Spinner

>Hey Wilbur

Welcome to a new life! It sounds that you already have the bug.

Something that makes makeing the bottle stoppers much easier is to get a morris taper jacobs chuck to put in the lathe and then a mandrel to put in the chuck. When I make mine I cut a bunch of 2 x 2 x 2 1/2 pieces. I then drill and tap all at one time. Now all you need to do is thread each piece on to the mandrel and pull up the tail support and turn. You can do all of the shapeing, sanding and finishing at one shot. Just unthread and put it on the bottle stopper base. One thing I do is to put a little finishing wax on the bottom before I thread it on the mandrel. This wax finishes the bottom and helps in unthreading.

Have fun, good turning and be safe.

Bill in CG, AZ.

Re: Turning bootstrapping: is this par for the course?

#4

Re: Turning bootstrapping: is this par for the cou

Rick Allen

>Hey Eloit

I had a different take on Wilber's story.

I took it more like how I felt in KC when Arthur Mason selected your turning as one of the objects he wanted to talk about at the instant gallery critique. It was more of a celebration of woodturning than a puzzle to be solved.

Re: Turning bootstrapping: is this par for the course?

#5

The Vortex

Charles R. Smith from Victoria

>Wilbur,

It sounds like the Vortex has sucked you in. You should know that you can never escape. Take comfort in the fact that there are many, many others who are also caught in its clutches.

Charles (who got caught by the Vortex a year ago)

Re: Turning bootstrapping: is this par for the course?

#6

Yep. That sounds about right.

Raymond Overman in SC

>Don't worry, it'll get more involved when you get ready to start building jigs to do certain tasks. At least three trips to the local big box for parts and hours of scrounging on the Internet for ideas and plans. And there's always a special tool that you think would be neat to own.

Just go with it and enjoy the ride.

Re: Turning bootstrapping: is this par for the course?

#7

Sounds about right.

Steven Kubien

>Now you just have the accept the fact that the next project you tackle will involve a new set of jaws for your chuck. Ah heck, don't put it off...just buy a new chuck now with the jaws you need (saves time changing them later). Now about those gouges... Swept back sides? What angle are they ground at? Well, that's ok for now but you will want them at xyz-angle for the next project. Might as well order a set like that as well. Do the skews have a curve to the edge or are they straight across? Different tools for different applications. Might be good to have spares. How many lathes do you have? What?!?!?! Is that it? Well, here's what you need to do.......

Welcome to the madness.

Steve Kubien

Ajax, Ontario

Re: Turning bootstrapping: is this par for the course?

#8

Dick Hines

Re: Turning bootstrapping: is this par for the cou

Dick Hines

>Wood turning------spending money. The same thing.

Re: Turning bootstrapping: is this par for the course?

#9

Re: Turning bootstrapping: is this par for the cou

wilbur

>Hi Eliot,

I forgot to throw a bunch of these into my post: :@) :@) :@)

But just to address your concerns:

The Thompson skew chisel has a 1/2" tang that is 5/16" thick, and needs a 5/8 inch hole to accept it. The handle making article on the Thompson website actually recommends a 5/8" hole, with some wedges made from a dowel to keep things in place.

I do know what really sharp tools can do -- I am primarily a hand tool guy, and am pretty familiar what a good razor sharp chisel is like. As far as my old carbon steel tools go, I think that part of what was happening was that I was doing a long planing cut ending in a rollover at high RPMs on a piece of white oak, and that created enough heat to blue the very edge. I could see the discoloration. The metal at the very edge of these tools is pretty thin, so I can see how a small area right at a sharp edge can get pretty hot.

Once I got the handle for the Thompson skew done and put together, it cuts like a dream. Like I said, using it to make a handle for the spindle gouge was a lot easier.

Re: Turning bootstrapping: is this par for the course?

#10

That's how I built my entire shop. :)

john lucas

>

Re: Turning bootstrapping: is this par for the course?

#11

Welcome to the Wonderful World of Woodturning.

Brian Hahn in SW Wisconsin

>

Re: Turning bootstrapping: is this par for the course?

#12

Re: Turning bootstrapping: is this par for the cou

Tommy Holmes

>You'll have to replace that old lathe too!

Re: Turning bootstrapping: is this par for the course?

#13

Steven Antonucci

Just wait until you upgrade the lathe...

steve antonucci

>

Re: Turning bootstrapping: is this par for the course?

#14

Wilbur, this is what I call Going through life....

Barry Irby

>But First.

I would turn some ornaments, but first, I need some new tools.

I would use my new tools, but first I have to make handles.

I would make the handles, but first I have to find a 1" ferral.

I would drill a 5/8" hole, but first I have to go to the Borg and buy a bit.

I would go to the Borg, but first I have to clean the sawdust off my self and find my Keys.

So yes, your story sounded petty familiar to me.

I would get the bit, but first I have to stop and the ATM and get some cash.

I would get some work done in the shop, but first I have to figure out what it was I started out to do.

Re: Turning bootstrapping: is this par for the course?

#15

Re: Turning bootstrapping: is this par for the cou

eliot d

>Well then, you are doing just fine. I'm sorry that I got the idea that you were inexperienced. By the way, why couldn't you turn a 5/8 " hole in the end of the handle?

Re: Turning bootstrapping: is this par for the course?

#16

Re: Turning bootstrapping: is this par for the cou

eliot d

>Rick, it's always a pleasure to see your posts. You just seem to know stuff -- like Russ Fairfield. But I don't understand this one. I certainly was thrilled in KY when Arthur Mason and John Jordan selected my piece for comment; but I don't know what "puzzle" you are referring to. Can you clarify?

Re: Turning bootstrapping: is this par for the course?

#17

Re: Turning bootstrapping: is this par for the cou

wilbur

>Oh, I'm definitely inexperienced in woodturning. I have experience sharpening, but woodturning is pretty new to me.

I'm not sure what you mean by turning a 5/8" hole in the handle. The way I did it was to put a 5/8" bit in a drill chuck in the headstock, put the handle on a live center on the tailstock and line up the drill bit with the center of the handle, and then used the tailstock crank to advance the handle into the drill bit.

Re: Turning bootstrapping: is this par for the course?

#18

Re: Turning bootstrapping: is this par for the cou

eliot d

>Oh, I was simply trying to say that if you have to drill a hole of whatever size, and you don't have a drill bit to do it the way you did, you can always chuck up the handle one way or another and approach the end with a sharp tool to cut the hole -- sort of like a small box. I am delighted that you are enjoying turning the bottle stoppers, they make great presents. Have you tried chatter work on the end grain? It's easy and great fun, and you can color them with felt tip markers. You are on your way!

Re: Turning bootstrapping: is this par for the course?

#19

jim miles

Re: Wilbur, this is what I call Going through life

jim miles

>There is more to Woodturning than putting chisel to wood

there is collecting and learning about various woods.

collecting and making tools, jigs and equipment.

learning to sand, finish

Once you think you are getting prety good at something another challenge comes along to take you in another direction.

It is a never ending journey that makes woodturning so interesting.

Enjoy the ride!

Re: Turning bootstrapping: is this par for the course?

#20

Re: Turning bootstrapping: is this par for the cou

eaglesc

>It appears that most involved in turning try to find new ways to spend money.

I do not believe that the wood knows how much you paid for the steel that shaved it.

If you had good results on a 2x4 congratulations!

I have found soft woods more problematic than hard woods.

As far as carbon steel goes I keep a diamond stone next to ma at the lathe and cannot remember the last time I used a motorized abrasive method to sharpen my tools.

I Use no jigs to sharpen and turn a variety of mixed materials on my Jet and RIkon minis.

THere is no great need to spend a lot of money if you don't want to.