Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Allen wrench tool questions

Posts

Allen wrench tool questions

#1

Allen wrench tool questions

keith zimmerman, Normal IL

>I'm working on an allen wrench hollowing tool and have a couple of questions about mounting it in a handle. I'm going to be doing mini forms no more than 2" tall.

What size wrench should I use? I was thinking that 1/8" or 3/16" would work.

How long can I extend the shaft before getting vibration?

I would be grateful for any and all answers...and thanks in advance.

keithz

Re: Allen wrench tool questions

#2

Re: Allen wrench tool questions

JohnKJordan in East TN

>Keith,

I'm an amateur toolmaker compared to others here, but I would use the largest allen wrench that would fit into the intended opening and extend it the minimimum possible distance. Vibration would be a function of the allen wrench composition (more or less fixed), crossection geometry (fixed), thickness, total and unsupported length, and the nature and speed of the wood being turned (highly variable) - I don't think it is possible to determine the maximum extended length without knowing the others.

BTW, I suspect vibration might be reduced by annealing the shaft (not the tip) - that would make an interesting experiment. Anealing should certainly make the shaft less brittle.

JKJ

Re: Allen wrench tool questions

#3

Re: Allen wrench tool questions

Brian Hahn in SW Wisconsin

>I hollow Christmas ornaments with tools made from 5/32" and 3/16" hex wrenches.

I have a drill chuck mounted on a handle and use that to hold the Allen wrenches, screw drivers, etc.

Re: Allen wrench tool questions

#4

Re:Brian- I try to find long .....

Jamie Donaldson

>...Allen wrenches so that I have sufficient shaft length to epoxy into a wooden handle. The diameter of the shaft generally determines how far you can hollow without rest support, and smaller shafts will flex and chatter moreso than larger ones-1/4" and up. I also harden the cutting tips for better edge holding ability, but they can be used without any heat treating required.

Re: Allen wrench tool questions

#5

Re:OOoppps!Meant to address this to Keith!

Jamie Donaldson

>

Re: Allen wrench tool questions

#6

Steven Antonucci

Lots of good info so far...

steve antonucci

>Here's what I've done-

1.) The handles on small tools don't need to be small. I made some tiny tools with tiny handles and they require a death grip.

2.) The tips are usually too long as-is. I cut them down about 1/2 way before sharpening, since I can always angle the tool through the opening to reach further with less torque.

3.) Hardened or not, they cut.

4.) Make several sizes. A smaller tool will fit through a larger hole, and a variety of tools is better than not having what you need. I use smaller diameter tools at an angle to the entry hole to undercut smaller vessels.

Steven

Re: Allen wrench tool questions

#7

Re: Allen wrench tool questions

Lan Brady

>Keith,

I bought a 25 piece set of long handle allen wrenches at harborfreight.

I made hollowing tools from many sizes from 1/8: up to 1/2"

I use the 1/8" more than the others put together.

I reach in about 1-1/2" without any concern.

I use the larger sizes to reach the deepest points. Also the larger sizes gives you the smoother finish.

The surpise (to me) was the smallest size removed the most wood quickly.

Like Brian, I mounted a jacobs chuck in a handle and use it. This allows the bits to be sharpened easily and dont take up so much room with all those handles.

Lan

Re: Allen wrench tool questions

#8

Would Someone Post a Photo of the Allen Tool?

Chicago Bob

>

Re: Allen wrench tool questions

#9

Any photos of grinds used on these tools??

Tim GC

>

Re: Allen wrench tool questions

#10

Re: Any photos of grinds used on these tools??

Lan Brady

>Tim,

i do not have a camera yet.

I grind a flat on what will be the top and then round the nose just like a scraper.

I put one bend in the wrench so that the point is in line with the shaft. That stops the torque advantage of the wood.

Lan

Re: Allen wrench tool questions

#11

Allen wrench tools 

Brian Hahn in SW Wisconsin

>


img

Re: Allen wrench tool questions

#12

Thanks for all the great answers everyone.

keith zimmerman, Normal IL

>Sharing like this is what makes Wood Central the best place to learn.

keithz

Re: Allen wrench tool questions

#13

Thanks Gents now I get it, DOH!!!

Tim GC

>

Re: Allen wrench tool questions

#14

Re: Allen wrench tools

don central illinois

>Thanks, I have always had too much of a bend in mine. This helps wonderfully. As the saying goes, one picture is worth, etc. etc.