Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

1/2" steel bar

Posts

1/2" steel bar

#1

1/2" steel bar

joaz

>Hi all, after watching Escoulen using his bedan tool on Utube, I decided to make on myself and give it a try.

Anyone know where's a good place to by square 1/2" high speed steel?

As always, thanks in advance.

Re: 1/2" steel bar

#2

Re: 1/2" steel bar

Robert Henderson

>McMaster-Carr at mcmaster.com

Re: 1/2" steel bar

#3

Re: 1/2" steel bar

Brian Hahn in SW Wisconsin

>Most industrial supply houses (i.e. McMaster-Carr) don't carry 1/2" square HSS steel stock. You can get 1/2" square lathe cutting bits, but they are only 4" long. However they do carry air hardening and oil hardening 1/2" square stock.

Remember, if you use HSS stock you will need to heat treat it since it usually comes annealed.

The most cost effective source that I have found for larger pieces of tempered HSS is to buy a HSS scraper of the appropriate size and grind it as needed.

Re: 1/2" steel bar

#4

Re: 1/2" steel bar

gtwilkins

>Joaz,

I go to Napa here in Canada and buy key stock, it comes in 12" lengths and sizes from 1/8- 1/2" then I got a piece of heavy 3/4" square tubing and the 1/2" key stock slides in if you ease the corners. I drilled and tapped the square tubing to hold the key stock (2 grub screws) and I shape both ends, Bedan and round nose scraper, I use closed cell pipe insulation on the tubing for grip.

Hope this helps, Trevor

Re: 1/2" steel bar

#5

Re: 1/2" steel bar

john lucas

>Unless I'm mistaken you can't harden HSS yourself without some sophisticated equipement. You can heat treat High Carbon steel quite successfully and it makes a good bedan tool.

Also if I'm correct the official bedan is tapered and not square. I made mine square. I don't use it often because I'm comfortable with the skew. I should practice with it more. Jean Escoulen does wonderful things with it.

Re: 1/2" steel bar

#6

Re: 1/2" steel bar

Gordon Seto

>The bedans that Jean Escoulen uses are square or rectangular.

The one that has trapezoid shape is English bedan. It is not suitable for what he does. He is using the bedan with the bevel up; the acute angle on the flat side corners would dig into the tool rest. He recommends softening the corners on the square edges.

I think if there is enough interest, probably Doug would expand the Thompson tool line. We will never know.

Gordon

Re: 1/2" steel bar

#7

Re: 1/2" steel bar

Stuart Johnson

>I was watching the video and can't see any difference between the bedan and a good mortise chisel. I have a set of Steve Knight chisels and just might have to give them a go.

Re: 1/2" steel bar

#8

Re: 1/2" steel bar

john lucas

>Stewart they work fine. I tried one of mine. In fact I fashioned my homemade bedan after that one only I made mine wider and thinner and a steeper angle than my mortising chisel.

Re: 1/2" steel bar

#9

Re: 1/2" steel bar

joaz

>Thanks everyone for the great info. The bordom of winter is making me try something new.

Re: 1/2" steel bar

#10

Re: 1/2" steel bar

Bob Macgregor

>What kind of steel is the key stock? I tried an internet search and key stock (from various suppliers) ranged from cold rolled, hot rolled/low carbon, stainless and unspecified steels (many zinc-coated). Was the Napa key stock HSS?

Re: 1/2" steel bar

#11

Re: 1/2" steel bar *LINK*

Walter Ahlgrim

>look at enco.com item 383-5533 1/2 inch square 8 inchs long 10% cobalt

I made 3/8 beading tool from one seem to stay sharp forever.

Walta


Enco.com

Re: 1/2" steel bar

#12

Re: 1/2" steel bar

Paul Zerjay

>Which is better, oil quench, or water quench? And after the quench, how do you know what temperature to bring it back to for tempering?

Re: 1/2" steel bar

#13

Re: 1/2" steel bar

gtwilkins

>I believe so, it grinds like it is and it was a machinist friend who told me about it. He also makes lathe tools out of crowbars.

I have half a dozen tools I've made out of key stock and it seems to hold an edge just as long as my bought scrapers.

Trevor

Re: 1/2" steel bar

#14

It's soft if you can drill or cut it with a file.

Al Crandall -NW of Indy-

>