Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

air bubbles in epoxy

Posts

air bubbles in epoxy

#1

air bubbles in epoxy

john lucas

>I'm trying to help a friend who makes jewelry that is filled with colored epoxy. She has the same problems I have when using Inlace or some of the clear resins. I always get a bubble or two that you try to fill and then when you are turning or sanding the fill down you open it up and have to fill again.

Does anyone know how to elimanate the bubbles. We tried a vacuum and it raises the bubbles to the surface but they don't pop and level. We didn't have a vacuum gauge and she was using a refrigerator compressor that her husband rigged up so I don't know how much vacuum it was pulling.

I know we have a lot of knowledgeable people here so I thought I would throw this out and see. Thanks

Re: air bubbles in epoxy

#2

Re: air bubbles in epoxy *LINK*

Bob Macgregor

>I have a paperweight with a dandelion seed head embedded in resin... with no bubbles... and have always wondered how this is done. There are a number of web sites that advertise this as a service/business (see link) , but I haven't seen a writeup on how it is accomplished.


http://www.duttcom.com/MiniBeasts/

Re: air bubbles in epoxy

#3

Re: air bubbles in epoxy

john lucas

>I've used Cast-N-Craft to imbed objects in acrylic resin but when I use it on wood I often get the bubbles. i think it's because air or moisture may be trapped in the wood. One of the things we are going to try is to mix her colorants with some Cast-n-craft and see if that works better than her epoxy. I didn't have any more to try when we did experiments the other day. Thanks for the link

Re: air bubbles in epoxy

#4

Re: air bubbles in epoxy

Rick Allen

>The main things are to

use slow cure epoxy

warm it in place to make it runny

vibrate the epoxy to release bubbles

pop the bubbles as you can

Some say breathing on the epoxy will release bubbles, something about the CO2.

Re: air bubbles in epoxy

#5

JL

Re: air bubbles in epoxy

JL

>One method that I used to use way back when....

I was casting epoxy resins for use in TEM (transmission electron microscopy). I would dilute the two parts (just a little) and draw a reasonably high vacuum on the two parts separately. Then I would mix the parts, embed the specimen and draw a vacuum on the mixed resins.

It wasn't quite the same type of epoxy. Why don't you ask the biology department at your school how they do it?

Re: air bubbles in epoxy

#6

Re: air bubbles in epoxy

Dick Coers

>Some of the pen guys (making their own resin pens)put the blanks in a paint pressure pot (Harbor Freight) and let it cure under pressure.

Re: air bubbles in epoxy

#7

Re: air bubbles in epoxy

john lucas

>Tried all that. So far mixed results.

Re: air bubbles in epoxy

#8

Re: air bubbles in epoxy

john lucas

>Thanks I'll look into diluting. What did you use to dilute it with? I think some have mentioned alcohol.

Re: air bubbles in epoxy

#9

Re: air bubbles in epoxy

john lucas

>Thanks Dick We can reverse the output of the compressor and put pressure instead of vacuum. That would be a quick trial.

Re: air bubbles in epoxy

#10

Re: air bubbles in epoxy

Doug Turner

>John, There is a bootle stopper group on yahoo that has several epoxy casters. They use the Haror freight pressure pots and add colorants to the epoxy. I believe there are some detailed discussion groups.

Re: air bubbles in epoxy

#11

Re: air bubbles in epoxy

Brian Hahn in SW Wisconsin

>I dilute with acetone (disappears fast) or alcohol (slower evaporation).

Re: air bubbles in epoxy

#12

JL

Re: air bubbles in epoxy

JL

>If I were back in the lab, I would try ethyl acetate. An alcohol might work though.

Re: air bubbles in epoxy

#13

Re: air bubbles in epoxy

Bart Rhoads

>I dont know if this would apply to epoxy but a good friend of mine used to do a lot of acrylic casting and when the casting show bubbles he would go over the top of the casting with a propane torch and it would draw the bubbles to the surface. The flames would just barely lick the surface. You might try that on a another piece and see if this would work. I never have tried it but I have watched him do it.

Re: air bubbles in epoxy

#14

Re: air bubbles in epoxy

john lucas

>Thanks Brian I usually clean it up with Acetone and assumed it would work for thinning if it didn't change the charactaristics of the epoxy.

Re: air bubbles in epoxy

#15

Re: air bubbles in epoxy

john lucas

>Doug Are you sure it's Bootle. Maybe Booty? Nah it must be Bottle stopper. Thanks I'll try to look them up.

Re: air bubbles in epoxy

#16

Re: air bubbles in epoxy

Brian Hahn in SW Wisconsin

>I depends on the thickness of the epoxy. Acetone will evaporate from a normal glue-up thickness within minutes, long before the epoxy has had time to set up. I'd be more cautious with thick castings, but a little heat or vacuum will remove the acetone long before it sets up.

I prefer acetone for thinning because it doesn't contain the water that alcohol does. On the other hand I like alcohol for clean-up because it seems to work better and doesn't evaporate while I'm still trying to wipe up the mess.

Re: air bubbles in epoxy

#17

Re: air bubbles in epoxy

Ruth Harding

>Here is just one link to a whole discussion on casting and problems from the IAP board.

They have one section called 'casting & Stabilizing' which address all of these issues and how to fix them.........23 pages worth.

http://www.penturners.org/forum/topic.asp?TOPIC_ID=30399

Re: air bubbles in epoxy

#18

Re: air bubbles in epoxy

Ken Oakley-Sunny St. Cloud, Fla

>A propane torch is my favorite method also. Works for me. The air expands and the bubble bursts-

Re: air bubbles in epoxy

#19

Re: air bubbles in epoxy

robert davis

>

Re: air bubbles in epoxy

#20

Re: air bubbles in epoxy

JohnKJordan in East TN

>John,

Years ago when I ran a small nuclear fuels metallography lab, I eliminated air bubbles in samples by pulling a gentle vacuum for a few minutes just after casting. The bubbles came to the surface as you said, but if I warmed the epoxy first it was lower viscosity so the bubbles popped easier. I reduced the vacuum while the epoxy was still liquid. The large bubbles will have expanded and come to the surface and the tiny bubbles remaining would usually shrink back down to nothing. I didn't have to vacuum treat the epoxy before casting but that sounds like a great idea.

It didn't take much vacuum - if too much it made way too many bubbles just like boiling water. Of course, much may depend on the TYPE of epoxy - what I used was specifically made for preparing metallographic samples with vacuum. It was fairly thin to start with and had a long set time. Maybe check with metallographic industrial supply companies?

Be careful about heating epoxy - if you get it too warm you can get a thermal runaway (it must be an exothermic reaction) and it will get very hot, set up too fast, turn a burnt brown color, and crack.

JKJ

Re: air bubbles in epoxy

#21

Re: air bubbles in epoxy

Jorge Castaneda~Downeast Maine

>John,

Beth Ireland, uses epoxy in her turnings, if I remember well, she applies a coat to the wood to seal the pores and then when this coat starts to congeal, she pours the rest, she uses colors and embeds stuff in there.

Maybe there is some info from her somewhere.

Re: air bubbles in epoxy

#22

Re: air bubbles in epoxy

Glenn Hodges, Nashville, GA

>I use a paint stripper gun and gently apply heat to the epoxy on my bottle stoppers. This makes the bubbles rise to the surface.