Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Nova 1624 stand question

Posts

Nova 1624 stand question

#1

Nova 1624 stand question

Mark Trulock

>Hi

I just bought a Nova 1624 and I love it. The only thing I would like is a bit more stability. The reviewer in the Fine Woodworking tool test built a stand and added 200 pounds of sand. He said that his shop build stand helped dramatically reduce vibration.

Has anyone here modified the existing stand to add a shelf for ballast? If so how did you do it?

Thanks

Mark Trulock

Re: Nova 1624 stand question

#2

JL

Re: Why not make your own stand?

JL

>That way you could incorporate drawers, a ballast box and whatever. You could put levelers on each leg.

You can probably drill and tap each leg and mount cross-supports and then mount a ballast box (or whatever) on your cross-supports.

Another (more expensive alternative) would be to get Teknatool's cast iron leg set and mount a ballast box.

Re: Nova 1624 stand question

#3

Re: Nova 1624 stand question

Paul Vicchitto

>I did for mine.....I will try to post a picture later today. I essentially built a box around the legs by drilling and bolting 3/4 " plywood to the legs. I had to close up the box tight to prevent sand from running out! I also was trying to leave space under the legs for room to sweep. It seems to have worked out. I have approximately 300-350 lbs of sand in the box and then I mounted 2 left over ballast boxes from my Shopsmith turning days on the back edge of the box for a total 500- 600 lbs ballast.....A huge improvement !!! Pics to follow when i have time.

Paul

Re: Nova 1624 stand question

#4

When I was considering a Nova

Jerry Hall

>I looked into making my own lathe stand. Here are a couple I liked:

http://www.shopnotes.com/issues/067/extras/mini-lathe-stand/

http://www.plansnow.com/lathestnd.html

I think I favored the last one because of the mass and rigid construction (depending on your joinery skills!) I also liked that it left me foot and knee room to do the "dance." It's tempting to fill in all that space under with storage, and then you end up with lower back pain :)

Hope this helps.

Re: Nova 1624 stand question

#5

Re: Nova 1624 stand question

Steven Kubien

>I bought my 1624 second-hand and here is what the original owner did...

Two lengths of 1.5" x 3" steel tubing, 1/4" wall thickness (might be 1/8", not sure). Make these the length of the bed. Attach the two lengths with threaded rod (1/2" or 5/8") at each end so you end up with a rectangular frame which fits between the legs. This frame is suspended by HEAVY chain which is attached to the lathe itself by the bolts which hold the legs to the frame (probably have to buy longer bolts to accomodate the chain thickness). Ballast is supplied by whatever you store on this frame (bowl blanks, bags of sand, whatever). I am about to add some 20 litre water jugs to absorb vibration.

So far this system has worked really well and it is pretty simple to make. I'll try to snap a picture or two tonight and post them.

HTH

Steve Kubien

Re: Nova 1624 stand question

#6

Re: Nova 1624 stand question

Walter Ahlgrim

>You want a steel stand. Trees are designed to be flexible nothing made of wood is ridged.

Ballast works better the closer it is to the work and the more firmly they are connected.

Never put the stands legs were you want to put your feet plan then carefully.

The photo shows the stand with the wheels. I have a small scissor jack that will lift the stand to remove the wheels. I rarely install the wheels. Since the photo I have installed AC outlets under the stand. My stand is very heavy 350 pounds made from 4 steel plates � inch thick 9 inches wide 4 feet long. Plans are available on request.


img

Re: Nova 1624 stand question

#7

Re: Nova 1624 stand question

Jorge Castaneda~Downeast Maine

>Mark,

My lathe is a Nova 3000, the previous incarnation of yours, and came without a stand, in the picture you can see what I did, a simple frame of 2x4"s a double layer of plywood for the top, surrounded on three sides by 5/8 plywood, at the base, a double bottom created with 2x8", made a space big enough to fit 3 sand bags that the local Ace hardware sells for winter use, each weights 70 pounds and the stand itself some 100 pounds and the lathe 190, so it ended up around 500 pounds, the space under is where blanks and roughed pieces land and so it weights a ton, I had very unbalanced 16" bowl blanks in there and it did not dance or shake. It is not attached to the floor, it just sits in there.

Hope this helps

Jorge


img

Re: Nova 1624 stand question

#8

Re: Nova 1624 stand question

Paul Vicchitto

>Hers the picture of my stand.


img

Re: Nova 1624 stand question

#9

Re: Nova 1624 stand question

Mark Trulock

>Wow

Thanks for all the great ideas. I wanted to modify the Nova stand if I could, but I may try one of the other stands.

Thanks again

Mark Trulock